Connects2 CAM-KIT12 User manual

• Wireless 2.4GHz Radio Transmission
• Wide Viewing Angle (110 °)
• Night Vision Functionality
• IP68-Rated Waterproof
• User-Friendly Menu
• Variable Parking Lines (6 Sizes)
• Mirror/Original Image Display Options
User Manual
Prior to Installation
Read the manual prior to installation. Technical knowledge is necessary for installation. Please ensure you
use the correct tools to avoid damage to the vehicle or product.
Connects2 can not be held responsible for the installation of this product.
Technical Support
Connects2 want to provide a fast and suitable resolution should you encounter any technical issues. With this
in mind, when contacting Connects2, try to provide as much Information as possible. This will speed up the
process and help us to help you.
Please use our dedicated online technical support centre: support.connects2.com
Digital Wireless Reversing Camera Kit
PRODUCT FEATURES
CAM-KIT12
BOX CONTENTS
- LCD 4.3” Monitor with Connector Cable
- Suction Cup Mount
- Car Charger with Connector Cable
- Power Box with Antenna
- Reversing Camera with Connector Cable
- Instructions

www.connects2.com
2
Connects2Vision
CAMERA INSTALLATION
1. Remove the license plate from the vehicle
(Fig. 1)
2. Mark the location where the reversing camera
will be installed (left, middle or right). (Fig. 2)
3. Tear off the 3M tape on the back of the cam-
era bracket, and x the camera at the marked
location. (Fig. 3)
4. Tear off the 3M tape on the front of the cam-
era bracket and x it to the license plate. Then
tighten up the screws to x the license plate in
place.
(Fig. 4)
5. Find a suitable opening/drill hole near the
license plate opening into the interior of the
vehicle. For added visibility and easy installation,
remove the interior trim near the license plate.
(Fig. 5)
6. Now run the camera cable to connect to the
power box in the vehicle’s interior/cavity. Be sure
the cables
aren’t pinched or knotted. Connect the plug
of the camera cable to the 4-Pin socket of the
power box. (Fig. 6)
7. Open the inner plastic panel and remove it
from the hatch or tailgate. Test the wires with a
multimeter to nd the reverse light power wire.
Connect the red wire from the power box to the
reverse light power wire. Then connect the black
wire from the power box to a ground source
(vehicle chassis). (Fig. 7)
8. Secure the rear camera cable and power box
cable with cable ties in the rear carriage. Be sure
thereare no electrical loads or metal between
the monitor and antenna to avoid impairing the
transmission.
9. Put the car charger into the vehicle’s cig-
arette lighter to power on the monitor. If the
power box is correctly connected, a signal will
be transmitted to the monitor when putting the
car into reverse and the monitor will display the
camera image.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6

www.connects2.com 3
Subscribe to our YouTube Channel for installation
guides and tips... www.youtube.com/connects2
MONITOR INSTALLATION
1. Open the locking screw and adjust the monitor
to the desired viewing angle. Then tighten the
screw to secure the monitor.
2. Make sure the area of the windscreen designat-
ed for the installation of the monitor is free from
dust and dirt.
3. Press the suction cup base onto the windscreen
and move the locking lever downward towards
the suction cup base.
4. Connect the monitor cable to the car charger
cable and plug the car charger into the vehicle’s
12V power socket.
MONITOR BUTTON FUNCTIONALITY
Fig. 7

www.connects2.com
4
Connects2Vision
Pairing the Monitor and Camera
By default, the monitor should be automatically paired with the camera included in the
CAM-KIT12 kit. In order to ensure that the camera pairs with the monitor successfully,
please make sure that the camera is powered on within 30 seconds after turning on the
monitor.
To manually pair the camera or to pair a new camera, press the ‘MODE’ button so that
the monitor enters ‘pairing mode’. The indicator light will ash quickly and a loop icon
will be displayed on the monitor screen. Power up the reversing camera and pairing with
the monitor will happen automatically. Once pairing is complete, the camera image will
appear on the monitor screen and the indicator light will stop ashing.
Choosing Guideline Size
Firstly, put the vehicle into reverse gear. After the image has been displayed on the mon-
itor screen, hold down ‘MENU’ for 3 seconds. You will now be able to choose between six
sizes of guideline using the ‘UP’ and ‘DOWN’ buttons. Press ‘OK’ to select.
USER GUIDE
Turning on the Monitor
The monitor will automatically power on after it is connected to the vehicle’s 12V power
socket. The boot logo will appear on screen and the indicator light will be red if it has
been connected successfully.
Accessing the Monitor Menu
Press the ‘MENU’ button to access menu mode. The display will show the menu for ap-
prox. 5 seconds
Use the ‘UP’ and ‘DOWN’ buttons to move through the options and press ‘OK’ to select.
Use the ‘UP’ and ‘DOWN’ buttons to increase, decrease or advance the desired option
and press ‘OK’ to select.
Pair Pair the monitor with a new reversing camera
B/C Control Adjust the monitor’s brightness and contrast settings
Mirror/Normal Switch between mirror and normal image modes
Guide Line Activate or deactivate parking guidelines
Reset Default to factory settings
To leave the menu, wait for 5 seconds without pressing any buttons