evertz 9780slke2-h264hd User manual

9780SLKE2-H264HD
HD/SD-SDI Dual StreamLINK™ MPEG2/H.264/AVC Encoder
© Copyright 2012
EVERTZ MICROSYSTEMS LTD.
5288 John Lucas Drive,
Burlington, Ontario, Canada
L7L 5Z9
Phone: [phone]
Sales Fax: [phone]
Tech Support Phone: [phone]
Tech Support Fax: [phone]
Internet: Sales: [e-mail]
Tech Support: [email protected]
Web Page: http://www.evertz.com
Version 1.1, February 2012
The material contained in this manual consists of information that is the property of Evertz Microsystems and is intended
solely for the use of purchasers of the 9780SLKE2-H264HD. Evertz Microsystems expressly prohibits the use of this manual
for any purpose other than the operation of the device.
All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz
Microsystems Ltd. Copies of this guide can be ordered from your Evertz products dealer or from Evertz Microsystems.

This page left intentionally blank

IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “Dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (Servicing) instructions
in the literature accompanying the product.
•Read these instructions
•Keep these instructions.
•Heed all warnings.
•Follow all instructions.
•Do not use this apparatus near water
•Clean only with dry cloth.
•Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
•Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
•Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
•Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles and the point where they exit from the apparatus.
•Only use attachments/accessories specified by the manufacturer
•Unplug this apparatus during lightning storms or when unused for long periods of time.
•Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC –
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE
WARNING
DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO
OBJECTS FILLED WITH LIQUIDS ARE PLACED ON THE EQUIPMENT
WARNING
TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE
POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE
WARNING
THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE

INFORMATION TO USERS IN EUROPE
NOTE
CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to the European Union EMC directive. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
INFORMATION TO USERS IN THE U.S.A.
NOTE
FCC CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
WARNING
Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s
authority to operate the equipment.
Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface
cables with the shield connected to the chassis ground of the device must be used.

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Revision 1.1 Page i
TABLE OF CONTENTS
1. OVERVIEW...................................................................................................................................1
2. GETTING STARTED.....................................................................................................................2
3. TECHNICAL SPECIFICATIONS ...................................................................................................4
3.1. VIDEO INPUT.......................................................................................................................4
3.2. NETWORK INTERFACE ......................................................................................................4
3.3. SIGNAL ENCODING ............................................................................................................4
3.4. MONITORING ......................................................................................................................5
3.5. ELECTRICAL .......................................................................................................................5
3.6. PHYSICAL............................................................................................................................5
4. FRONT AND REAR PANELS .......................................................................................................6
4.1. FRONT PANEL.....................................................................................................................6
4.2. REAR PANEL.......................................................................................................................6
5. SERIAL INTERFACE ....................................................................................................................8
6. FIRMWARE UPGRADE PROCEDURE.......................................................................................10
6.1. OVERVIEW ........................................................................................................................10
6.2. INVOKE UPLOAD MODE VIA THE WEB INTERFACE......................................................10
7. SETUP ........................................................................................................................................11
7.1. STATUS..............................................................................................................................11
7.1.1. Monitoring ...............................................................................................................11
7.1.2. Active Interfaces......................................................................................................12
7.1.3. Route Table.............................................................................................................12
7.1.4. Logging ...................................................................................................................12
7.2. CONTROL..........................................................................................................................12
7.3. ENCODING - VIDEO ..........................................................................................................14
7.4. ENCODER – AUDIO 1 TO 8...............................................................................................15
7.5. ENCODER – DATA ............................................................................................................18
7.6. MULTIPLEX .......................................................................................................................19
7.6.1. PSI ..........................................................................................................................19
7.6.2. TRANSPORT..........................................................................................................20
7.6.3. IP TRANSPORT......................................................................................................20

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Page ii Revision 1.1
7.7. SYSTEM.............................................................................................................................21
7.7.1. Unit Control.............................................................................................................22
7.7.2. Error........................................................................................................................22
7.7.3. Upgrade..................................................................................................................22
7.7.4. Licenses..................................................................................................................22
Figures
Figure 1-1: 9780SLKE2-H264HD Block Diagram.............................................................................................1
Figure 4-1: Front Panel.....................................................................................................................................6
Figure 4-2: Rear Panel......................................................................................................................................6
Figure 5-1: Serial Port Setup ............................................................................................................................8
Figure 7-1: 9780SLKE2-H264HD Status Tab View........................................................................................11
Figure 7-2: Status Message............................................................................................................................11
Figure 7-3: 9780SLKE2-H264HD Control Tab View.......................................................................................12
Figure 7-4: 9780SLKE2-H264HD Encoding-Video Tab View.........................................................................14
Figure 7-5: 9780SLKE2-H264HD Encoding – Audio 1 Setting View ..............................................................15
Figure 7-6: 9780SLKE2-H264HD Dolby Encoding View.................................................................................16
Figure 7-7: 9780SLKE2-H264HD Dolby Encoding Data Format ....................................................................17
Figure 7-8: 9780SLKE2-H264HD Encoding – Data Tab View........................................................................18
Figure 7-9: 9780SLKE2-H264HD Multiplex Tab View....................................................................................19
Figure 7-10: 9780SLKE2-H264HD System ....................................................................................................21

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Revision 1.1 Page iii
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 First Release Jan 2012
1.1 Added Rear panel description and serial port menu details Feb 2012
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof
nor for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning
performance of Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The
only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order
confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no
warranty is granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or
order confirmation. Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If
you encounter an error, please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make
changes in equipment design or specifications.

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Page iv Revision 1.1
This page left intentionally blank

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Revision 1.1 Page 1
1. OVERVIEW
The 9780SLKE2-H264HD is designed to deliver high quality H.264 encoded video streams to the
IPTV network.
The 9780SLKE2-H264HD offers the following features:
•Dual MPEG2/H.264/AVC encoding of HD-SDI or SD-SDI signals
•MPEG-1 Layer II audio encoding or Dolby Pulse (optional)
•Compact 1RU design
•Configuration via HTTP web interface or via SNMP
The 9780SLKE2-H264HD can accept up to two HD-SDI or SD-SDI video signals with or without
embedded audio and apply exceptional H.264 or MPEG2 encoding to produce a superior mpeg over
IP output stream. The streaming output can be configured as either unicast or multicast delivery.
The configuration of the device is fully flexible allowing the user to configure various encoding
parameters including bitrate, GOP size, visual filter effects, network interface, and more. This device
can also de-embed the audio from the incoming video signal and apply MPEG-2 Layer II encoding or
optional Dolby Pulse encoding for up to 8 audio services.
The 9780SLKE2-H264HD has a dedicated control port that offers a built-in web server for quick and
easy configuration. The user can also store up to four unique profiles for recall at the touch of a
button. The 9780SLKE2-H264HD occupies 1RU and offers dual power supplies.
Features:
•High quality H.264 or MPEG2 encoding of HD/SD-SDI signals
•Equipped with MPEG-1 Audio Layer II encoding engine or optional Dolby Pulse
•Compact 1RU design with dual power supply
•Quick glance status monitoring LEDS at the front panel
•Easy to use web browser interface for configuration and control
Figure 1-1: 9780SLKE2-H264HD Block Diagram

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Page 2 Revision 1.1
2. GETTING STARTED
1. Set up inputs and outputs:
a. Connect one HD-SDI input to the BNC marked HD-SDI INPUT1 on the rear panel and the
second input to the BNC marked HD-SDI INPUT2.
b. Connect the IP management Ethernet cable to the CONTROL Ethernet port on the rear
panel.
c. To access the encoders’ IP output, connect an Ethernet cable to the DATA MAIN Ethernet
port on the rear panel. This can be connected to the decoder directly or via an Ethernet
switch.
2. Configure the encoder:
a. Verify that the computer is on the same control/management subnet as the encoder. For
example, if the encoder’s control/management IP address is 192.168.77.100, set the PC to
192.168.77.xxx where xxx is user’s choice.
b. Open a web browser and navigate to the Control IP address of the encoder, for example,
192.168.77.100.
c. Let us assume that Profile 1 applies to encoder 1 and Profile 2 applies to encoder 2. Go to
the Output tab and set the Transport Stream, TS, Bitrate and the Destination IP Address
and Port for both profiles. For example, the Destination IP Address and Port can be
239.79.0.100 and 1234. Unicast or multicast operation is strictly based on the destination IP
address entered here.
d. Navigate to the Encoder tab, select Profile 1 in the dedicated drop down box and set the
desired Video Bit Rate in bits/second (for example, 10000 for 10Mbps) and the other
encoding parameters listed in the interface. Click on “Save in Profile 1” button. Then
select Profile 2, set the encoding parameters for Profile 2 and click on “Save in Profile 2”.
Note that parameters marked with a red star require the specific encoder to be restarted.
From the System tab, select the encoder from the drop down menu and select the Restart
button.
e. Navigate to the Inputs tab, select Profile 1 in the dedicated drop down box and select the
desired Video Standard and Display Aspect Ratio, and any 1 of 8 audio types. Click on
“Save in Profile 1” button. Select Profile 2, set the parameters and click on “Save in
Profile 2” button.
f. Go to the Control tab. Both encoders can be activated by means of clicking on the
“Activate All” button. It is also possible to activate one encoder at a time by clicking on the
first of the three buttons on the left hand-side of the interface . The two other buttons
allow for the pausing and restarting of the encoder application .

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Revision 1.1 Page 3
g. If encoder IP address changes are needed, go to the System tab. Changes to the Data
ports can be done on Data Main’s and Data Back-up’s IP, Mask, and Gateway fields.
Changes to the control/management IP address can be done on the Control’s IP address,
Mask, and Gateway fields. Note: the control IP address and the data addresses cannot be
on the same subnet (for example, one at 192.168.77.xxx and the other two at
192.168.77.yyy); the first three octets must not be the same. The default address for the
Data port is 192.168.79.100.
Click on the “Apply Parameters” button if changes are made and the system will reboot. If
subnets have changed, reflect similar changes on the controlling PC.
3. Configure decoder:
a. For IP input, match whatever Destination IP and Port numbers are set for the encoder.
For example, per above, a decoder would need to receive on IP=239.79.0.100 and
Port=1234.
b. Make sure the decoder input is selected correctly to IP input.
4. Troubleshooting (should the system not respond as expected, confirm or perform the following
procedure):
a. Control/management interface can be pinged.
b. Both data interfaces can be pinged. Verify that the destination IP address and port values
match on the encoder and decoder. Test this by using VLC running on a PC to decode the
encoder’s MPEG-over-IP output stream.
c. Power cycle the encoder whenever there is an input format change.
d. If Control and Data are accidentally set to the same subnet, connect the Control cable to
the Data port and try surfing to both the Control and Data IP addresses.
e. If the Control IP address is unknown, connect the Control port to an Ethernet hub and run
Wireshark, which is available on http://www.wireshark.org/download.html, on a PC. Power
cycle the encoder and look for an IP address (power up message sourcing from encoder).
Factory support is necessary to identify other means of discovering the Control IP address.

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Page 4 Revision 1.1
3. TECHNICAL SPECIFICATIONS
3.1. VIDEO INPUT
Number of Inputs: 2 electrical
Standard: SMPTE 259M/292M (270Mb/s, 1.485Gb/s)
525i and 625i, 1080i and 720p
Connector: BNC per IEC 61169-8 annex A
Input Equalization:
SD: Automatic to 300m @ 270Mb/s
HD: Automatic to 110m @ 1.5Gb/s
Return Loss:
SD: >13dB up to 270MHz
HD: >15dB up to 1.5GHz
3.2. NETWORK INTERFACE
Number of Interfaces: 3 electrical
Main: Data streaming
Back-up: Data streaming
Control: HTTP web browser
SNMP through VistaLINK
Standard: Ethernet 10/100 base-T
IEEE 802.3U standard for up to 100Mb/s
Connector: RJ-45
3.3. SIGNAL ENCODING
Video Encoding Engine: H.264/AVC
MPEG2
Audio Encoding Engine: MPEG 1 Layer II
Dolby-E Pass Through
Dolby Digital AC-3 Pass Through
Optional Dolby Pulse
Traffic Shaping: Constant bit rate
GOP Structure: User Configurable GOP s
Video Resolution: 525i/625i/1080i/720p
Recommended Bit Rate: >=1Mb/s
Frame Encoding: IPB
Frame Rate: Full frame rate
Audio Channels: 8 audio services
Audio Output Bit Rate: Variable
Delivery: UDP Unicast/Multicast

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Revision 1.1 Page 5
3.4. MONITORING
Signal Detection: Video presence detection
Video standard detection
Audio presence detection
Error Notification: HTTP web browser status page
Card edge LED
3.5. ELECTRICAL
Voltage: Auto-ranging 100V-240V AC
50Hz/60Hz
Power: 60W
EMI/RFI: Complies with FCC Part 15
Class A EU EMC directive
Safety: TUV listed, complies with EU safety directive
3.6. PHYSICAL
Dimensions: 19" W x 1.75" H x 18.75" D
(483mm W x 45mm H x 477mm D)
Weight: 12lbs (4.4kg)

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Page 6 Revision 1.1
4. FRONT AND REAR PANELS
4.1. FRONT PANEL
The front panel of the 9780SLKE2-H264HD has 4 green LEDs.
Figure 4-1: Front Panel
1. PSU STATUS 1 and 2 – These LEDs indicate the status of both the power supplies. Under
normal operating conditions, these LEDs are expected to be green. If any PSU (Power Supply
Unit) fails or is not connected to mains power supply, the corresponding LED will turn off.
2. Activity – The activity LED corresponds to the processor activity of the unit.
3. Status – The Status LED indicates that the unit is powered ON.
4.2. REAR PANEL
There are various interfaces on the back panel of the 9780SLKE2-H264HD.
Figure 4-2: Rear Panel
1. Serial A – This is a 9 pin DB male connector which is a serial interface to the encoder. This can
be hooked to any serial port client application e.g. Hyper Terminal or Tera Term. The settings
required on the serial client application are as per the picture below.
2. VGA A – This 15 pin VGA connector is used for connecting a monitor to the encoder. This is
intended for use by Evertz support staff only.
3. USB A – This USB port is used for connecting a keyboard to the encoder. This is intended for
use by Evertz support staff only.
4. USB B – This USB port is used for connecting an external USB storage device to the encoder.
This is intended for use by Evertz support staff only.

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Revision 1.1 Page 7
5. DATA Main/Redundant – The encoder has two Ethernet ports on the back labelled “Data Main”
and “Data Redundant”. These ports are used for streaming out the encoded ASI over IP. One is
the main data port and the other port can be configured as a redundant data port (which is an
exact copy of the main data). Output IP stream from encoders 1 & 2 are present on both the
Ethernet ports.
6. HD/SD-SDI Input 1 & 2 – These BNC connectors are used to feed a baseband signal to
Encoder 1 & 2 respectively.
7. Control – The third Ethernet port on the rear panel of the encoder is labelled “Control”. This is
used to control the encoder via Web-Interface.
8. Power Supply Sockets – There are two power supply sockets on the rear side of the encoder.
These are used for connecting both the power supplies of the encoder to mains AC supply.

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Page 8 Revision 1.1
5. SERIAL INTERFACE
The serial interface of the encoder can be used to configure the IP addresses.
1. Connect serial interface on the back of the Encoder to Tera Term. Connection
parameters are illustrated in Figure 5-1.
Figure 5-1: Serial Port Setup
2. Press enter. You will see a login prompt like this debian3480 login.
Use “customer” for both login ID and password.
3. Once you are logged in, you will see the following menu:
Eth3 settings
address: 192.168.192.28
netmask: 255.255.255.0
gateway: 192.168.192.1
DHCP IS TURNED OFF
1) Change IP
2) Change netmask
3) Change gateway
4) Turn DHCP ON/OFF
5) Change ethernet to read
6) Run eth_mod1.sh
7) Run eth_mod2.sh
8) APPLY AND EXIT
9) EXIT
What is your choice?

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Revision 1.1 Page 9
Options 1 through 4 can be used to configure the IP address, Netmask, Gateway and DHCP on the
selected Ethernet interface. In the example in step 3, the selected interface is “eth3”.
Option 5 can be used to change the selected Ethernet interface, i.e. to select eth0; Press 5 and enter
and then press 0 and enter.
eth0 is for Data Main interface
eth1 is for Data Redundant interface
eth3 is for Control network

Please Note: Options 6 and 7 are for Evertz support staff only. It is recommended
that these settings are not handled by the user.
Once the control IP address (eth3) is set on the encoder, set the correct IP address of the PC so that
the encoder port can be pinged. Then start any web browser and enter the control IP address of the
encoder to open the configuration interface, e.g. http://192.168.192.28/

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Page 10 Revision 1.1
6. FIRMWARE UPGRADE PROCEDURE
6.1. OVERVIEW
The firmware in the 9780SLKE is contained on a FLASH EPROM. From time to time firmware updates
will be provided to add additional features to the unit. The firmware update can be initiated using the
web interface.
You will need the following equipment in order to update the Firmware:
•PC where the web interface that controls the encoder has been opened following the steps
specified in section 6.2.
•New firmware supplied by Evertz.
6.2. INVOKE UPLOAD MODE VIA THE WEB INTERFACE
1. Select the System tab on the web interface.
2. Click on Choose Fileat the bottom of the System tab next to Upgrade and select the
appropriate firmware on your PC.
3. Select Upgrade. The encoder will take approximately 10 seconds to come back online.

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Revision 1.1 Page 11
7. SETUP
7.1. STATUS
The Status tab shows the general status of the 9780SLKE2-H264HD.
Figure 7-1: 9780SLKE2-H264HD Status Tab View
7.1.1. Monitoring
Status: This field shows the name of the active profiles, or sets of configuration parameters, of the two
encoders and the expected resolution of the incoming video signal.
Note that the box does not auto-detect the input video standard and, therefore, the user should indicate
the appropriate input standard in the Encoding-Video tab. If there is a mismatch between the selected
input standard and the incoming standard, the following message is displayed. The same message is
reported if there is no input to the box.
Figure 7-2: Status Message

9780SLKE2-H264HD
9780SLKE2-H264HD Dual HD/SD-SDI StreamLINK™ MPEG2/H.264/AVC Encoder
Page 12 Revision 1.1
7.1.2. Active Interfaces
The following active interfaces are available: “Data – Main”, “Control”, “Data – Backup”. The following
parameters can be configured for the active interfaces:
•IP: This field displays the IP address for the respective interface.
•Mask: This field displays the mask address for the respective interface.
•Gateway: This field displays the gateway mask for the respective interface.
•MAC address: This field displays the Media Access Control (MAC) address for the respective
interface.
7.1.3. Route Table
The Route Table displays the interface to which each destination is routed.
•Destination: This field displays the destination IP address for the respective destination.
•Gateway: This field displays the gateway address for the respective destination.
•Genmask: This field displays the genmask address for the respective destination.
•Interface: This field identifies the interface that is linked to the respective destination.
7.1.4. Logging
•Last Error: This field displays the time and date of the last reported error.
•Clear Error Log: Selecting the Clear button enables the user to clear the existing logged
errors.
•View Error Log: Selecting the View button enables the user to view the existing logged errors.
7.2. CONTROL
Figure 7-3: 9780SLKE2-H264HD Control Tab View