Corghi Artiglio Master Code User manual

Cod. 4-118329D - 10/2017
English User Manual
Tel. ++39 0522 639.111 - Fax ++39 0522 639.150
www.corghi.com - [email protected]
Artiglio
Master Code

2 Artiglio Master Code User Manual
TRANSLATION OF ORIGINAL INSTRUCTIONS (ITALIAN)
Copyrighted materials. All rights reserved.
The information contained herein may be subject to modifications without prior notice.
Thank you for choosing our Tyre Changer
CORGHI
Dear Purchaser
Thank you for purchasing your Corghi Tyre Changer.
Your Tyre Changer has been designed to provide years of safe and dependable service,
as long as it is used and maintained in accordance with the instructions provided in this
manual.
All persons who will use and/or maintain this Tyre Changer must read, understand and
follow all warnings and instructions provided in this manual, and be properly trained.
This Owner’s Manual should be considered an internal part of your Tyre Changer and
should remain with the Tyre Changer. However, nothing in this manual, and none of the
devices installed on the Tyre Changer, substitute for proper training, careful operation,
good judgement and safe work practices.
Always be sure that your Tyre Changer is in optimum working order. If you suspect that
anything is not working properly, or that a dangerous situation may exist, immediately
shut down the Tyre Changer and remedy any condition before you proceed.
If you have any questions concerning the proper use or maintenance of your Tyre Changer,
please call your authorized Corghi representative.
Sincerely,
Corghi
OWNER INFORMATION
Owner
Name_______________________________________________________________
Owner
Address_____________________________________________________________
Model
Number_____________________________________________________________
Serial
Number_____________________________________________________________
Date
Purchased___________________________________________________________
Date
Installed ____________________________________________________________
Service and Parts
Representative_______________________________________________________
Phone
Number_____________________________________________________________
Sales
Representative_______________________________________________________
Phone
Number_____________________________________________________________

Artiglio Master Code User Manual 3
UK
TRAINING CHECKLIST
Trained Declined
Safety Precautions
Warning and Caution Labels
Pinch Points and Other Potential Hazards
Safe Operating Procedures
Maintenance and Performance Checks
Mounting Head Inspection
Adjustment and Lubrication
Self-diagnostics procedures
Maintenance messages and instructions
Clamping
Steel / Alloy Wheels
Reverse Drop Centre Wheels
Close Centre Wheels
Bead Breaking
Standard Wheels
Low Profile Wheels
Demounting
Bead Lubrication During Removal of Low Profile Tyres
Reverse Drop Centre Wheels
Mounting
Standard Wheels
Mounting of Stiff, Low Profile Tyres
Reverse Drop Centre Wheels
Proper Bead Lubrication for Mounting Protection
WDK procedure
Automatic procedures
Automatic Size Identification Procedure
Machine Use in Automatic Mode
Emergency Procedures in Automatic Mode
Accessories
Instructions for the Correct Use of Accessories
Bead Sealing and Seating
Instructions for Using Inflatron (optional)

4 Artiglio Master Code User Manual
Inflation
Safety Precautions
Lubrication and Removal of Valve Core
Bead Sealing and Seating
Individuals and Dates Trained
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________

Artiglio Master Code User Manual 5
UK
TABLE OF CONTENTS
1. GETTING STARTED ...............................................................................7
1.1 INTRODUCTION.....................................................................................................7
1.1.a. Purpose of the manual............................................................................................... 7
1.2 FOR YOUR SAFETY ................................................................................................ 7
1.2.a. General warning and instructions............................................................................. 8
1.2.b. Decal placement ...................................................................................................... 11
1.2.c. Electrical and pneumatic connections................................................................... 16
1.2.d. Technical data........................................................................................................... 17
1.2.e. Air pressures ............................................................................................................. 17
1.3 SPECIAL RIM/TYRE CONSIDERATIONS ............................................................18
1.4 INTENDED USE OF THE MACHINE ..................................................................18
1.5 EMPLOYEE TRAINING ........................................................................................ 18
1.6 PRE-USE CHECKS................................................................................................ 19
1.7 DURING USE ........................................................................................................ 19
2. TRANSPORT, STORAGE AND HANDLING........................................20
2.1 UNPACKING..........................................................................................................20
3. HOISTING/HANDLING........................................................................21
3.1 INSTALLATION ..................................................................................................... 22
3.2 INSTALLATION CLEARANCES............................................................................24
4. ARTIGLIO MASTER CODE DESCRIPTION.........................................24
4.1 OPERATOR POSITION .........................................................................................25
4.2 EQUIPMENT COMPONENTS (MAIN WORKING ELEMENTS OF THE MACHINE)26
4.3 CONTROLS ...........................................................................................................28
4.3.a. Main switch................................................................................................................ 28
4.3.b. Operating console.................................................................................................... 28
4.3.c. Pedal unit .................................................................................................................. 30
4.3.d. Display for configuring and displaying wheel data ............................................ 30
4.3.e. Pressure gauge with deflation push-button ......................................................... 31
4.4 OPTIONAL ACCESSORIES SUPPLIED ON REQUEST ......................................31
5. BASIC PROCEDURE - USE ..................................................................32
5.1 TURNING THE MACHINE ON............................................................................. 33
5.2 PRELIMINARY CHECKS....................................................................................... 34
5.3 LOADING AND CLAMPING THE WHEEL.......................................................... 34
5.3.a. Deflating the tire ...................................................................................................... 36
5.4 AUTOMATIC WORK PROCEDURE...................................................................... 37
5.4.a. Advanced automatic features (7 sequences)........................................................ 38
5.4.b. Basic automatic features (4 sequences)................................................................ 50
5.5 MANUAL WORK PROCEDURE ........................................................................... 61
5.5.a. Manual configuration of wheel data....................................................................... 61
5.5.b. Bead breaking ......................................................................................................... 61
5.5.c. Demounting............................................................................................................... 61

6 Artiglio Master Code User Manual
5.5.d. Mounting ................................................................................................................... 64
5.6 APPROVED UHP AND RUN FLAT TYRE DEMOUNTING AND MOUNTING
PROCEDURE............................................................................................................... 67
5.7 TYRE INFLATION .................................................................................................68
5.7.a. Safety indication....................................................................................................... 68
5.7.b. Inflating tyres............................................................................................................ 69
5.7.c. Special procedure .................................................................................................... 70
5.8 UNCLAMPING AND UNLOADING THE WHEEL ..............................................72
5.9 MENU’ ...................................................................................................................73
5.9.a. Language ................................................................................................................... 73
5.9.b. Video ......................................................................................................................... 73
5.9.c. Help online................................................................................................................ 74
5.9.d. Release Software-Database.................................................................................... 74
5.9.e. Service ....................................................................................................................... 74
5.9.f. Options ....................................................................................................................... 74
5.9.g. Date/Time.................................................................................................................. 75
5.9.h. TPMS .......................................................................................................................... 75
5.9.i. Calibrate Touch Screen............................................................................................. 82
5.9.l. Calibrate Laser .......................................................................................................... 82
5.9.m. Diagnostik P3K ........................................................................................................ 85
6. OPTIONAL ACCESSORIES ..................................................................87
6.1 INFLATRON ..........................................................................................................87
6.1.a. Inflation...................................................................................................................... 88
6.1.b. Possible error messages ......................................................................................... 90
6.2 CAMERA ................................................................................................................91
6.3 TREAD THICKNESS MEASURING SENSOR .....................................................93
6.4 TEMPERATURE MEASURING SENSOR.............................................................95
6.5 TPMS...................................................................................................................... 96
6.6 LUBRICATORS ...................................................................................................... 98
7. MAINTENANCE..................................................................................100
8. TROUBLESHOOTING ........................................................................104
9. ENVIRONMENTAL INFORMATION..................................................106
10. INFORMATION AND WARNINGS ABOUT HYDRAULIC FLUID...107
11. INFORMATION AND WARNINGS ABOUT LUBRICATING FLUID
FOR TYRES .......................................................................................108
12. RECOMMENDED FIRE-EXTINGUISHING EQUIPMENT..............108
13. GLOSSARY ........................................................................................109
TABLE FOR USING CENTRING AND CLAMPING ACCESSORIES
ACCORDING TO RIM TYPE ..........................................................................................112
WIRING DIAGRAM .........................................................................................................121
PNEUMATIC DIAGRAM ................................................................................................. 130

Artiglio Master Code User Manual 7
UK
1. GETTING STARTED
1.1 INTRODUCTION
1.1.a. PURPOSE OF THE MANUAL
The purpose of this manual is to provide the instructions necessary for optimum operation,
use and maintenance of your machine. If you sell this machine, please deliver this manual
to the new owner. In addition, so we can contact our customers with any necessary safety
information, please ask the new owner to complete and return to Corghi the change of
ownership form attached to the previous page of this manual. Alternatively, the new owner
can send an email to [email protected].
This manual presumes that the technician has a thorough understanding of rim and tyre
identification and service. He/she must also have a thorough knowledge of the operation
and safety features of all associated tools (such as the rack, lift, or floor jack) being utilized,
and have the proper hand and power tools necessary to work in a safe manner.
The first section provides the basic information to safely operate the MASTER CODE tyre
changer family. The following sections contain detailed information about equipment, pro-
cedures, and maintenance. “Italics” are used to refer to specific parts of this manual that
provide additional information or explanation.
These references shouldbe read for additionalinformation to the instructions beingpresented.
The owner of the tyre changer is solely responsible for enforcing safety procedures and
arranging technical training. The tyre changer is to be operated only by a qualified and
trained technician. Maintaining records of personnel trained is solely the responsibility of
the owner or management.
The MASTER CODE tyre changer family is intended for mounting, demounting, and inflating
tyres of lightweight vehicles (cars, not trucks or motorcycles) with maximum dimensions of
47 inches in diameter and 16 inches in width.
Copies of this manual and of the documents accompanying the machine may be obtained
from Corghi by specifying the type of machine and its serial number.
NOTICE: Design details are subject to change. Some illustrations may vary slightly in ap-
pearance from the machine you have.
1.2 FOR YOUR SAFETY
HAZARD DEFINITIONS
These symbols identify situations that could be detrimental to your safety and/or cause
equipment damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
DANGER

8 Artiglio Master Code User Manual
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
WARNING
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION
NOTICE: Used without the safety alert symbol, indicates a potentially hazardous
situation, which, if not avoided, may result in property damage.
NOTICE
1.2.a. GENERAL WARNING AND INSTRUCTIONS
Avoid Personal Injury. Carefully read, understand and follow the warnings and instructions given in this manual.
This manual is an essential part of the product. Keep it with the machine in a safe place for future reference.
WARNING
1. If the use and maintenance procedures provided in this manual are not properly
performed, or the other instructions in this manual are not followed, an accident could
occur. Throughout this manual reference is made that “an accident” could occur. Any
accident could cause you or a bystander to sustain severe personal injury or death, or
result in property damage.
2. Overinflated tyres can explode, producing hazardous flying debris that may result in
an accident.
3. Tyres and rims that are not the same diameter are “mismatched.” Never attempt to
mount or inflate any tyre and rim that are mismatched. For example, never mount a
16.5” tyre on a 16” rim and vice versa. This is very dangerous. A mismatched tyre and
rim could explode, resulting in an accident.

Artiglio Master Code User Manual 9
UK
4. Never exceed the bead setting pressure provided by the
tyre manufacturer, as stated on the sidewall of the tyre.
Carefully monitor the gauge on the air hose.
5. Never place your head or any part of your body over a
tyre during the inflation process or when attempting to
seat beads. This machine is not intended to be a restrain-
ing device for exploding tyres, tubes or rims.
6. Always stand back from the tyre changer when
inflating, never lean over.
An exploding tyre and rim may be propelled upward and outward with enough force to cause
serious injury or death.
Never mount any tyre unless the tyre size (molded into the sidewall) matches the rim size
(stamped into the rim) exactly or if the rim or tyre are defective.
Never exceed the tyre pressure recommended by the tyre manufacturer.
This tyre changer is not a safety device and will not restrain exploding tyres and rims. Keep
the area clear of bystanders.
DANGER
7. Crushing Hazard. Moving Parts Present. Contact with moving parts could result in
an accident.
• Only one operator may work with the machine at a time.
• Keep all bystanders clear of the tyre changer.
• Keep hands and ngers clear of rim edge during the demounting
and mounting process.
• Keep hands and ngers clear of the mount/demount head dur-
ing operation.
• Keep hands and other body parts away from moving parts.
• Do not use tools other than those supplied with the tyre changer.
• Use proper tyre lubricant to prevent tyre binding.
8. Electric Shock Hazard.
• Never hose down or power wash electric tyre changers.
• Do not operate the machine with a damaged power cord
• If an extension cord is necessary, a cord with a current rating equal
to or greater than that of the machine must be used. Cords rated
for less current than the machine can overheat, resulting in a fire.
Avoid Personal Injury. Carefully read, understand and follow the warnings and instructions given in this manual.
This manual is an essential part of the product. Keep it with the machine in a safe place for future reference.
WARNING

10 Artiglio Master Code User Manual
• Care should be taken to arrange the cord so that it will not be tripped over or pulled.
9. Risk of Eye Injury. Flying debris, dirt and fluids may be discharged
during bead seating and the inflation process. Remove any debris
from the tyre tread and wheel surfaces. Wear OSHA, CE or other
approved safety glasses during mount and demount procedures.
10. Always inspect the machine carefully before using it. Missing, broken, or worn equip-
ment (including warning stickers) must be repaired or replaced prior to operation.
11. Never leave nuts, bolts, tools or other equipment on the machine. They may become
trapped between moving parts and cause a malfunction.
12. NEVER install or inflate tyres that are cut, damaged, rotten or worn. NEVER install a
tyre on a cracked, bent, rusted, worn, deformed or damaged rim.
13. If a tyre becomes damaged during the mounting process, do not attempt to finish
mounting. Remove from the service area and properly mark the tyre as damaged.
14. To inflate tyres, use short bursts while carefully monitoring the pressure, tyre, rim and
bead. NEVER exceed the tyre manufacturer’s pressure limits.
15. This equipment has internal arcing or sparking parts which should not be exposed
to flammable vapours (gasoline, paint thinners, solvents, etc.). This machine should not
be located in a recessed area or below floor level.
16. Never operate the machine if you are under the effects of alcohol, medications and/
or drugs. If you are taking prescription or over the counter medication, you must consult
a medical professional regarding any side effects of the medication that could hinder
your ability to operate the machine safely.
17. Always use OSHA, CE or other approved and mandated Personal
Protective Equipment (PPE) during use of the machine. See your
supervisor for more instructions.
18. Remove jewellery, watches, loose clothing, ties and restrain long hair before using
the machine.
19. Wear non-slip safety footwear when operating the tyre changer.
20. Wear proper back support and employ a proper lifting technique when placing, mov-
ing, lifting or removing wheels from the tyre changer.
21. This machine may only be used, maintained or repaired by properly trained employ-

Artiglio Master Code User Manual 11
UK
ees of your company. Repairs should only be performed by qualified personnel. Your
CORGHI service representative is the most qualified person. The employer is responsible
for determining if an employee is qualified to safely make any repairs to the machine
should repair be attempted by users.
22. The user should understand all warning decals affixed to this equipment before
operating.
23. Lock the rim on the turntable during inflation.
1.2.b. DECAL PLACEMENT
No. Part Number Drawing Description
1
4-105844 DECAL, MI POWERED SYSTEM
2
446429 DECAL, MAX. INLETPRESSURE
16 BAR
3
446442 DECAL, WARNING UNDER
PRESSURE TANK
4
446598 DECAL, DISCONNECT POWER
SUPPLY
5
461936 DECAL, ONE OPERATOR ONLY
6
418135 DECAL, DIRECTION OF ROTA-
TION
7
4-103881 DECAL, CORGHI LOGO
8
4-111304 DECAL, WHEEL LOCKING
PEDAL
9
4-111305 DECAL, WHEEL UNLOCKING
PEDAL

12 Artiglio Master Code User Manual
No. Part Number Drawing Description
10
1010283 DECAL, LASER
11
4-108519 DECAL, MASTER CODE
12
462081 DECAL, HAND CRUSHING
HAZARD
13
4-105431 DECAL, CORRECT FEEDING
NETWORK
14
462778 DECAL, SAFETY INSTRUC-
TIONS
15
461933 DECAL, INFLATING PEDAL
16
461932 DECAL, TURNTABLE ROTA-
TION PEDAL
17
462080 DECAL, ACOUSTIC AND VISU-
AL PROTECTION
18
461930 DECAL, FOOT CRUSHING
HAZARD
19
425211 DECAL, ELECTRIC HAZARD
20
DECAL, MODEL SERIAL NUM-
BER

Artiglio Master Code User Manual 13
UK
42015-Correggio (RE) Italy
ISO9001
Code
SerialN.
X-XXXXXXXX/XX-XX
XXXXXXXXX
QUAL.SYS.CERTIFIED
ANNODICOSTRUZIONE/
MANUFACTURED
Mod.
V
A
kW
Hz
Ph
bar7psi
Port.max
.
15
6
7
8
9
11
12
14
15 16
7
18
12

14 Artiglio Master Code User Manual
42015-Correggio (RE) Italy
ISO9001
Code
SerialN.
X-XXXXXXXX/XX-XX
XXXXXXXXX
QUAL.SYS.CERTIFIED
ANNODICOSTRUZIONE/
MANUFACTURED
Mod.
V
A
kW
Hz
Ph
bar7psi
Port.max
.
2
3
4
10
13
20
19
18
12
17

Artiglio Master Code User Manual 15
UK
DANGER WARNING DECALS
part nr 462081. Crushing Hazard.
part nr 461930. Crushing hazard.
part nr 461936. Never stand behind the machine.
Only one operator may operate and use the machine.
part nr 446442. Danger - pressurised container.
part nr 425211A. Risk of electrical shock.
part nr 1010283. Caution - laser radiation.
Never look at the laser beam.
part nr 425083. Earth ground terminal.

16 Artiglio Master Code User Manual
1.2.c. ELECTRICAL AND PNEUMATIC
CONNECTIONS
The dimensions of the electric hook-up
used must be suitably sized in relation to:
• the electric power absorbed by the ma-
chine, indicated on its data plate (Fig. 1);
• the distance between the machine and
the power supply hook-up point, so that
voltage drops under full load do not exceed
4% (10% during start-up) compared with the
rated voltage specified on the data plate.
- The operator must:
• t a power plug on the power supply
lead in compliance with the relevant safety
standards;
• connect the machine to its own electrical
connection - A, Fig. 2 - and fit a differential
safety circuit-breaker with 30 mA residual
current;
• t fuses to protect the power supply line,
rated as indicated on the general wiring
diagram in this manual;
• connect the machine to an industrial
socket; the machine must not be connected
to domestic sockets.
A
2
Make sure the available pressure and the rendered capacity of the compressed air system
are compatible with those required for correct machine operation - see the “Technical Data”
section. For correct machine operation, the compressed air supply line must provide a
pressure range from no less than 8.5 bar to no more than 16 bar and guarantee an air flow
rate greater than the average consumption of the machine, which is equal to 160 Nl/min.
For correct equipment operation, the air produced must be suitably treated (not
above 5/4/4 according to ISO 8573-1)
NOTICE
An effective grounding connection is essential for correct operation of the machine.
NOTICE
1

Artiglio Master Code User Manual 17
UK
1.2.d TECHNICAL DATA
- Tyre types processed.CONVENTIONAL - LOW PROFILE - RUN FLAT - BALOON BSR
- Wheel dimension range:
• rim diameter ................................................................................................ from 13” to 32”
• maximum tyre diameter ....................................................................................... 1200 mm
• maximum tyre width ..................................................................................... 400 mm (16”)
- Turntable:
• automatic positioning in relation to .......................................................................... tools
• resting side................................................................................................................flanged
• centring ..................................................................................................................... on cone
• automatic ............................................................................................................... clamping
• drive system.......................................................................... 2-speed motor-inverter unit
• rotation torque........................................................................................................1200 Nm
• rotation speed ........................................................................................................7-20 rpm
- Wheel lifter:
• lifting capacity...............................................................................................................85 kg
- Power supply:
• electric 1Ph....................................................................................... 230V-0.98 kW 50/60Hz
• electric 1Ph (alternative) ................................................................ 110V-0.98 kW 50/60Hz
• compressed air operating power: .......................................................................8 -10 bar
• Min. air operating ow: ..................................................................................... 160 Nl/min
- Weight ..........................................................................................................................595 kg
- Weight of electric/electronic parts ................................................................................. 49 kg
- Noise level:
• Weighted sound pressure level A (LpA) in the work place ........................... < 70 dB(A)
The noise levels indicated correspond to emission levels and do not necessarily represent safe
operating levels. Although there is a relationship between emission levels and exposure levels,
this cannot be used reliably to establish whether or not further precautions are necessary. The
factors which determine the level of exposure to which the operator is subject to include the
duration of the exposure, the characteristics of the workplace, other sources of noise, etc. The
permitted exposure levels may also vary according to the country. However, this information
will enable machine users to make a more accurate assessment of hazards and risks.
1.2.e. AIR PRESSURES
The machine is equipped with an internal pressure limiting valve to minimize the risk of
over inflating the tyre.
•EXPLOSION HAZARD
•Never exceed the tyre pressure recommended by the tyre
manufacturer. Never mismatch tyre size and rim size.
•Avoid personal injury or death
DANGER

18 Artiglio Master Code User Manual
1. Never exceed these pressure limitations:
• Supply line pressure (from compressor) is 220 psi (15 bar).
• Operating pressure (gauge on regulator) is 145 psi (10 bar).
Bead setting pressure (gauge on hose) is the tyre manufacturer’s maximum pressure as
stated on the sidewall of the tyre
2. Activate air inflation jets only when sealing the bead.
3. Bleed air pressure system before disconnecting supply line or other pneumatic
components. Air is stored in a reservoir for operation of inflation jets.
4. Only activate the air inflation jets if the rim securing device is locked in place and
the tyre is properly clamped (when possible).
1.3. SPECIAL RIM/TYRE CONSIDERATIONS
Wheels equipped with low tyre pressure sensors or special tyre and rim designs may require
special procedures. Consult wheels and tyre manufacturers' service manuals.
NOTICE
1.4. INTENDED USE OF THE MACHINE
This machine must be used only to remove and replace an automotive tyre on an au-
tomotive rim, using the tools with which it is equipped. Any other use is improper and
can result in an accident.
The machine can not work on motorcycle wheels.
1.5. EMPLOYEE TRAINING
1. The employer is obligated to provide a programme to train all employees who service
rim wheels in the hazards involved in servicing those rim wheels and the safety procedures
to be followed. Service or servicing means the mounting and demounting of rim wheels,
and related activities such as inflating, deflating, installing, removing and handling.
• The employer shall insure that no employee services any rim wheel unless the em-
ployee has been trained and instructed in correct procedures of servicing the type of
wheel being serviced, and in safe operating procedures.
• Information to be used in the training programme shall include, at a minimum, the ap-
plicable information contained in this manual.
2. The employer shall ensure that each employee demonstrates and maintains the ability
to service rim wheels safely, including performance of the following tasks:
• Demounting tyres (including deation).
• Inspecting and identifying rim wheel components.
• Mounting tyres.

Artiglio Master Code User Manual 19
UK
• Using any restraining device, cage, barrier, or other installation.
• Handling rim wheels.
• Inating the tyre.
• Understanding the necessity to stand back from the tyre changer during tyre ination
and during inspection of the rim wheel following inflation, never leaning over.
• Installing and removing rim wheels.
3. The employer shall evaluate each employee’s ability to perform these tasks and to
service rim wheels safely, and shall provide additional training as necessary to assure
that each employee maintains his or her proficiency.
1.6. PRE-USE CHECKS
Before beginning work, carefully check that all components of the machine, especially
rubber or plastic parts, are in place, in good condition and working properly. If the inspec-
tion reveals any damage or excessive wear, no matter how slight, immediately replace
or repair the component.
1.7. DURING USE
In the event you hear any strange noise or feel unusual vibration, if a component or
system is not operating properly, or if there is anything unusual at all, stop using the
machine immediately.
• Identify the cause and take any necessary remedial action.
• Contact your supervisor if necessary.
Never allow any bystander to be within 20 feet of the machine during operation.
To stop the machine in an emergency:
• disconnect the power supply plug;
• cut off the compressed air supply network by disconnecting the shut-off valve (snap
coupling).

20 Artiglio Master Code User Manual
2. TRANSPORT, STORAGE AND HANDLING
Conditions for transporting the machine
The tyre changer must be transported in its original packing and stowed in the position shown
on the packing itself.
- Packing dimensions:
• width ............................................................................................................................... 1150 mm
• depth .............................................................................................................................. 1950 mm
• height .............................................................................................................................. 2100 mm
- Weight of wooden packing:
• STD version ........................................................................................................................ kg 710
Machine storage and shipping specifications
Temperature: -25° - +55°C.
Do not stack other goods on top of the packing or damage may result.
NOTICE
Handling
To move the packing, insert the tines of a fork-lift
truck into the slots on the base of the packing itself
(pallet) (Fig.3).
Before moving the machine, refer to the HOISTING/
HANDLING section.
Keep the original packing in good conditions to be used if the equipment has to be
shipped in the future.
NOTICE
2.1. UNPACKING
Remove the upper part of the packing and make sure the machine has not been damaged
during transportation.
3