Costway TQ10104 User manual

Toy Road Roller
TQ10104
USER’S MANUAL
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
EN FR

Before You Start
General Warnings:
The product must be installed and used under the supervision of an adult.
Read through each step carefully and follow the proper order.
Remove all packaging, separate and count all parts and hardware.
Please ensure that all parts are correctly installed, incorrect installation can lead to
a danger.
We recommend that, where possible, all items are assembled near the area in
which they will be placed in use, to avoid moving the product unnecessarily once
assembled.
Ensure a secure surface during installation, and place the product always on a flat,
steady and stable surface.
Please use this product with caution. The use of this product requires superb skills
to avoid accidents to the user or others due to a fall or collision.
Please wear suitable protective equipment during use, e.g. protective helmet,
gloves, knee pads, elbow pads etc.
Warnings:
Attention! Use it with protective equipment.
Attention! Not use it in the traffic.
Attention! The product is not suitable for the children under 3 years.
Please read all instructions carefully and keep it for future reference.
02

WARNING:
The trailer of this product is only for decoration, passenger
and loading are not allowed!
WARNING:
Must be assembled by an adult.
OWNERS MANUAL
with Assembly Instructions
Read and understand this entire manual before using!
Please keep this manual for future reference as it contains important
information.
Before first time use, charge the battery for at least 4-6 hours, but no
more than 10 hours.
◎ Suitable for 3+ Years
◎ Maximum user weight:
30 kg/66 lbs
03

About Your New Vehicle
On the purchase of your new Ride-On.
This ride-on car will provide your child with many miles of riding of
enjoyment. To help assure you and your rider a safe ride we ask
you to please read this manual carefully, and keep it for future
reference.
Follow the recommendations in this manual, they are designed to
improve the safety and operation of your ride-on car and its rider.
Specification
Suitable age:
Charge time:
Load capacity:
Size:
Speed:
3+ Years
8~12 hours
30 kg(66 lb)
125 x 50 x 52.5 cm(49 x 20 x 21 inch)
3-8 km/h(2-5 mph)
Battery
Charger
input
Motor
12V7AH X1
12V1000mA
Depend on local voltage
390-16000
● Non-rechargeable batteries are not to be recharged.
● If removable rechargeable batteries are used, the are only to be
charged under adult supervision.
BATTERY INFORMATION
04

● Remove rechargeable batteries from the product before charging.
● Do not mix old and new batteries. Do not mix different types of
batteries: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
● Insert batteries as indicated inside the battery compartment,
anode to anode, cathode to cathode.
● Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Battery leakage and
corrosion can damage this product. Dispose of batteries safely.
● Never short circuit the battery terminals.
Parts List
NO.
1
2
3
4
5
6
7
8
9
10
11
PART NAME
Vehicle body
Front wheel
Driving wheel
Ø10 washer
Ø8 lock nut
Ø8 socket wrench
Driving wheel hubcap
Normal wheel hubcap
Arm hubcap
Steering wheel
M5X30 machine screw
REMARK
Placed on the
steering wheel
Q’TY (PCS)
1
2
2
12
10
2
2
2
6
1
1
05

NO.
12
13
14
15
16
17
18
19
20
21
PART NAME
Ø5 nut
Seat
Φ4x12 round head screw
Middle axle
Rotation shaft
Right arm
Left arm
Bucket
Charger
Remote controller
REMARK
Placed on the
steering wheel
Q’TY (PCS)
1
1
5
1
1
1
1
1
1
1
Assembly tools required (not included):
Screwdriver
06

Parts Diagram
1
6
2
8
7
4
5
9
99
4
5
4
19
14
4
4
5
5
59
9
5
5
4
3
10
11
17
13
15
16
18
12
20
21
45
4
4
9
07

Safety
PREVENT INJURIES AND DEATHS:
• NEVER LEAVE CHILD UNATTENDED. ADULT DIRECT
SUPERVISION IS REQUIRED. Always keep child in view
when child is in vehicle.
• This toy should be used with caution since skill is required to
avoid falls or collisions causing injury to the user or third
parties.
• Protective equipment should be worn.
• Never use in roadways, near cars, or on near steep inclines
or steps, swimming pools or other bodies of water.
• Always wear shoes, always sit on the seat.
• Not to be used in traffic.
• This toy is unsuitable for children under 36 months due to its
maximum speed; Maximum user weight is 30 kg(66 lb).
• This toy has no brake.
WARNING:
• CHOKING HAZARD! Not suitable for children under 36 months.
• Must be assembled by an adult.
08

• Keep Children within Safe Riding Areas:
- Never use in roadway, near motor vehicles, on lawn space, on or
near steep inclines or steps, swimming pools or other bodies of
water;
• Use the toy only on flat surfaces. Such as inside your house,
garden or playground.
• Never use in the dark. A child could encounter unexpected
obstacles and have an accident.
Operate the vehicle only in the daytime or a well-lit area.
• It is prohibited to change the circuit or add other electric parts
• Inspect wires and connections of the vehicle periodically.
• Do not let any child touch the wheels or be near them when the
car is moving .
• This vehicle has adjustable play seat belts. Please instruct children
how to tie the safety belt before using, guarantee the security.
Rules for Safe Riding
09

Attach the Roller
7
7
1
2
3
4
5
6
1
Right Arm
There are four stopers on
the Middle Axle.
Rotation Axle without
stoper.
4. Pass the rotation axle through the hole at the end of the right
arm.
5. Fit a Ø10 washer to the end of the rotation axle.
6. Tighten a Ø8 lock nut to the end of the rotation alxe with a Ø8
socket wrench.
7. As shown, fit the roller to the roatation alxe on the right arm.
1. Insert the middle alxe passes
through the hole in the middle of
the right arm, and make the
stopers of the middle alxe fit into
the groove on the right arm.
2. Fit a Ø10 washer to the end of
the middle axle from the outside
of the right arm.
3. Tighten a Ø8 lock nut to the
end of the middle alxe with a Ø8
socket wrench.
10

Attach the Left & Right Arm -1
5
1
3
4
5
4
3
2
1. Attach the right arm to the hexagonal shaft on the right side of
the vehicle body.
2. Attach the left arm to the hexagonal shaft on the left side of the
vehicle body. Tip:The left and right arms must be assembled
horizontally and symmetrically. When assembling, insert the middle
axle and rotation axle into the corresponding holes of the left arm
at the same time.
3. Fit a Ø10 washer on each end of the hexagonal axle.
4. Tighten a Ø8 lock nut to each end of the hexagonal axle with two
socket wrenches.
5. Insert the arm hubcaps to the both arms.
Remove the Ø10 washers and Ø8
lock nuts on the hexagonal axle on
both sides of the carhead.
11

1
2
3
6
6
3
4
5
Attach the Left & Right Arm -2
2. Tighten a Ø8 lock nut. Tip: Use two Ø8 socket wrenches to
tighten the Ø8 lock nuts on both ends of the middle alxe at the
same time.
3. Fit an arm hubcap on each side of the middle axle.
4. Fit a Ø10 washer to the rotation axle that passing through the
left arm.
5. Tighten a Ø8 lock nut. Tip: Use two Ø8 socket wrenches to
tighten the Ø8 lock nuts on both ends of the rotation alxe at the
same time.
6. Fit an arm hubcap on each side of the rotation axle.
1. Fit a Ø10 washer to the
middle axle that passing through
the left arm.
12

Attach Driving Wheels
1
2
4
3
Turn the vehicle body downside up.
1. Slide a driving wheel onto the rear axle. Ensure the driving wheel
match up with gear box on the vehicle body.
2. Slide a Ø10 washer onto the rear axle.
3. Tighten a Ø8 lock nut to the end of the rear alxe.
Repeat steps 1-3 for the other driving wheel.
4. Insert the driving wheel hubcap to the driving wheel.
13

21
3
4
5
Attach Front Wheels
1. Slide a Ø10 washer onto the front axle.
2. Slide a normal wheel onto the front axle.
3. Slide a Ø10 washer onto the front axle.
4. Tighten a Ø8 lock nut to the end of the front axle.
5. Insert the hubcap to the front wheel.
Repeat for the other front wheel.
14

Attach the Steering Wheel & Connect the
Power Supply
3
1
2
Turn the vehicle body upright.
1. Fit the steering wheel to the end of
the steering column.
2. Line up the holes on the steering
wheel with the holes on the steering
column, insert the M5x30 machine screw.
3. Fasten a nut on
the opposite end of
the screw with a
screwdriver.
4. Plug the red
connector on the
vehicle body into the
red connector from
the battery.
4
15

Attach the Seat
Use Your New Ride-on
1. Fit the seat to the vehicle body.
2. insert five Ø4x12 round head screws and tighten.
1
2
1. ON/OFF button: Turns the vehicle on and off.
2. High / Low speed forward & Reverse shift:
Changes the direction that vehicle moves from forward to reverse.
16

● To move the vehicle forward in high speed, shift the lever to top
position.
● To move the vehicle forward in low speed, shift the lever to middle
position.
● To move the vehicle backward, shift the lever to down position
HINT: The vehicle is designed to operate in low speed only in
reverse.
3. Lights switch: Turns the vehicle lights on and off.
4. Foot pedal:
● To move the vehicle, press the pedal down.
● To brake or slow down, release pressure from the pedal.
5. Horn button: Press for horn or sound playing.
6. Adjust the angle of the roller.
Attach Front Wheels
1
2
5
34
6
IMPORTANT!
Always stop vehicle when changing the speed or direction to
avoid damage the gears and motor.
17

The arms has two lock positions, as shown hook the arm lock to the
iron pipe on the right side of the car to lock the arms.
How To Use Arms
Arms Lock Position A
Arms Lock Position B
18

A. USB slot (Maximum support 15GB)
B. Change the audio input (from the Bluetooth or the USB)
C. Play / Next
D. Decrease volume
E. Increase volume
F. Battery display: It displays the power level of the battery when
the vehicle stops. When one indicator remains, recharge the battery
please.
Use the Player
A
B
C D E
F
19

Attach the batteries of controller
Lift the battery compartment door on the back of the controller and
insert two AAA(LR03) batteries.
HINT: Batteries not included.
1. Build connection
Long press the forward and reverse buttons for 3 seconds, and the
speed indicator flashes. Then power on the vehicle, the speed
indicator goes to long bright, means the connection successful. If
the speed indicator no response, means the connection failed.
Replace the batteries and retry.
2. Brake button
Press the button to stop the vehicle, press it again to release the
brake.
Use the Remote Controller (IF
EQUIPPED)
Speed select
button Speed
indicator
Forward
button
Reverse
button
Left button
Brake
button
Right
button
20