Courtyard Creations RUS4239 User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
RUS4239
PAGE 1 OF 7 COURTYARD CREATIONS INC.
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. When contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
!
!
!
!
!
STOP DON’T RETURN TO STORE!

TOP CROSS BEAM
W/ADJUSTABLE TEETH
REAR UPRIGHT SUPPORT
FRONT UPRIGHT SUPPORT
LATERAL CROSS BRACE
REAR CROSS BRACE
RIGHT SEAT ARM
LEFT SEAT ARM
SEAT FRONT SUPPORT
SEAT REAR SUPPORT
SEAT ASSEMBLY
SWING ARM TUBE
U-SHAPED
SIDE CANOPY BRACE
FRONT/REAR CANOPY BRACE
PLASTIC JOINT COVER
SUSPENSION SPRING
BOLT M6*55
RUS4239-CS09-8
RUS4239-CS04-5
RUS4239-CS04-6
62RUS4239Q101
RUS4239-CS09-9
62RUS4040H102
62RUS4210I101
RUS4239-CS01-3
RUS4239-CS01-2
62RUS416BH101
RUS4239-CS09-7
RUS4239-CS02-1
62RUS4450M101
17GC06043401-Y3
17C01A0719072Y4
17C01A0721091Y4
Q'TY
BOLT M6*40
BOLT M8*80
SCREW ST4.2*16
WASHER d6.5*D16*1.2
WASHER d8.5*D17*1.6
PLASTIC WASHER
CANOPY/FRAME
CONNECTOR
PLASTIC SCREW
NUT WRENCH 13&17MM
HEX.KEY WRENCH 6MM
CUSHION
CANOPY
PILLOW
17C01A0714003Y4
17C01A0826011Y4
17C17A1306001Y4
17FA05050401-Y4
17FA08060601-Y4
18060616151401
1809030201
18000626005
28000J59001
17KAB1201----Y4
17KAA0201----Y4
61R4239C00000AA
61R4239D00000AA
61R4239J00000AA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
1
2
2
2
1
2
2
1
1
1
1
4
1
4
2
6
2
4
2
4
32
4
4
4
2
4
2
2
1
1
3
1
2
PAGE 2 OF 7
A. Read instructions thoroughly. Acquaint yourself with the inventory of parts and the
accompanying drawings to ensure safe and proper assembly.
B. You will need the following tools
- Phillips Screwdriver
- Nut Wrench (See Part #35)
- Hex. Key Wrench (See Part #36)
C. Lay out all parts on a flat surface and identify them using the table below.
PARTS LIST
BOLT M6*45
17C01A0716072Y4 4
BOLT M10*90
17C01A0928051Y4
BOLT M6*60
WASHER d10.5*D21*2.0
17FA09070701-Y4 8
STEEL NUT M10*1.5
17D02A050501-Y4
PLASTIC NUT M6*P1.0
16
16
18000C23001
18000337003
18000337002
BOLT CAP M10
BOLT CAP M6
418000337005
BOLT CAP M8
STOP DON’T RETURN TO STORE!
JAM NUT M8*1.25
17D03A040401-Y4 2
PART
NO. MATERIAL CODE PART

Note:
The labelled arrow marks on the rear cross
brace (#5) should be facing upwards.
Step 3:
Fasten the top cross beam w/adjustable teeth
(#1) to the front and rear upright supports
(#2 and #3) by using bolts (#15), washers (#21),
and steel nuts (#26). Do the same procedure
for both sides. See Fig. A – Step 3.
Step 5:
Fasten the rear cross brace (#5) to the rear
upright supports (#3) by using bolts (#17),
washers (#22) and plastic nuts (#27). Tighten
all of the plastic nuts and bolts.
See Fig. A – Step 5.
PAGE 3 OF 7
Step 1
Step 2
Step 3
Step 4
Step 5
Fig. A
Step 1:
Fasten the front and rear upright supports
(#2 and #3) at the top by using bolts (#15),
washers (#21), and steel nuts (#26). Do the
same procedure for both sides. Keep the bolts
loose. See Fig. A – Step 1.
Do not tighten bolts
after step 1, fasten
all bolts after step 5.
Step 2:
At both ends, insert the assembled upright
supports (#2 and #3) into the top cross beam
w/adjustable teeth (#1). See Fig. A – Step 2.
Step 4:
Fasten the lateral cross brace (#4) to the upright
supports (#2 and #3) by using bolts (#16) and
washers (#22). Do the same procedure for both
sides. See Fig. A – Step 4.
STOP DON’T RETURN TO STORE!
22
2
1
1
32
32
15
15
21
21
21
21
26
26
27
27
22 22 16
17
22
22
33
5
33
33
23
2
4
4
3
23
3
3
23
3
ASSEMBLY (Note: For all nuts and bolts
fastening, always use a washer (#21, #22 or #23)
between the tube and bolt or the tube and nut.)

PAGE 4 OF 7
Fig. B
Fig. C
Step 1
Step 3
Step 2
Step 4
Step 5
Step 1
Step 2
Step 8:
Insert the front and rear canopy brace (#7) ends
into the U-shaped side canopy braces (#6).
See Fig. B – Step 4.
Step 9:
Insert the four corners of the U-shaped side
canopy braces (#6) into the pockets of the
canopy (#37). See Fig. B – Step 5.
Step 7:
Insert the front and rear canopy braces (#7) into
the sleeves of the canopy (#37).
See Fig. B – Step 3.
Step 6:
Insert the U-shaped side canopy braces (#6)
into the canopy frame connectors (#28) and
secure with screws (#14). Please make sure
that the teeth of the canopy frame connectors
are facing towards the inside.
See Fig. B – Step 1 and Step 2.
Step 10:
Fasten the canopy/frame connectors (#37) on
the canopy assembly to the adjustable teeth
on the top cross beam w/adjustable teeth (#1)
by using plastic screws (#29). Do this procedure
for both sides. See Fig. C – Step 1 and Step 2.
STOP DON’T RETURN TO STORE!
628
37
37
37
37
1
29
28
29
28
7
7
7
7
66
28 14
14

PAGE 5 OF 7
Step 11:
Insert the seat arms (#8 and #9) into the seat
supports (#10 and #11) and fasten them together
by using plastic joint covers (#30), bolts (#18),
washers (#22), and plastic nuts (#27).
See Fig. D – Step 1.
Note:
1. The label marked "back" on the right seat arm
(#8) should coincide with the label marked
"back" on the seat rear support (#11) to ensure
proper assembly.
2. The clip holder side of the seat rear support
(#11) must face the inside of the swing and
the opening side of the clip holder must be
facing upward.
Step 12:
Open the seat assembly (#12) and attach its
back to the seat arms (#8 and #9) by using bolts
(#19), washers (#23), plastic washers (#31), and
jam nuts (#25). Repeat the same procedure for
both sides. See Fig. D – Step 2.
Step 13:
Make sure that the support brace on the seat
assembly (#12) is fully inserted into the clip
holders on the seat rear support (#11).
See Fig. D – Step 3.
Step 14:
Attach the swing arm tubes (#13) to the seat
arms (#8 and #9) by using bolts (#20), washers
(#22), and plastic nuts (#27). Repeat the same
procedure for both sides. See Fig. D – Step 4.
Step 15:
Hook the suspension springs (#24) into the top
of both holes of the swing arm tubes (#13). Do
the same procedure for both sides.
See Fig. D – Step 5.
back
back
back
back
Fig. D
STOP DON’T RETURN TO STORE!
back
back
8
8
10
19 23 23 25
31
34
12
12
11
13
13 13
13 13
13 13 27
27
22 22
22 22
20
20
33
33
13
24
24
24
24
11
30
18
22
22 27
33
9
9
8
9
support brace
Step 1
Step 2
Step 3
Step 4
Step 5
back
back

Step 19:
Please make sure that the safety locks on the
seat rear support (#11) are fully locked
whenever the seat assembly is in a swinging
position. See Fig. G – 1 (SEAT). To have the
swing in a bed position, open both of the safety
locks. See Fig. G – 2 (BED).
Step 18:
Place the cushions (#38) and the pillows (#39)
onto the seat assembly (#12). See Fig. F.
Fig. E
Fig. F
Fig. G
G–1(SEAT) G–2(BED)
PAGE 6 OF 7
Step 16:
Hang the opposite ends of the suspension
springs (#24) into the holes located on the
angled braces of the top cross beam w/adjustable
teeth (#1). See Fig. E.
Warning:
Make sure that both ends of the suspension
springs (#24) go completely through the holes
in the angled braces on the top cross beam
w/adjustable teeth (#1) and the swing arm
tubes (#13).
STOP DON’T RETURN TO STORE!
24
24
1
1
38 38
12
38
39
11
39
Step 17:
To assure stability, double check that all of the
bolts have been completely tightened and cover
them with bolt caps (#32, #33 and #34).

Step 20:
To flatten the seat assembly, lift up the safety
lock and remove the support brace.
See Fig. H1 and Fig. H2.
Then, insert the support brace into the rear
cross brace (#5). The seat assembly should
now be in a secured position and not moving
at all. See Fig. H3, Fig. H4, and Fig. H5.
Special Warnings
1. The user of this swing should always inspect it before each use.
2. It is essential to place this swing on level ground and not less than 6 feet away from any obstruction, such as
fences, garages, houses, overhanging branches, laundry lines, or electrical wires.
3. Check the tightness of all nuts and bolts on a regular basis.
4. Make sure that the suspension springs are properly secured before each use.
5. Always remove the canopy in heavy wind conditions, otherwise the swing may tip over and cause damage to its
parts.
6. The manufacturer will not accept responsibility for unauthorized repairs or modifications to the swing or its parts.
7. Oil all of the metal parts that move regularly.
8. Weight limit is 750 lbs.
PAGE 7 OF 7
Fig. H
Fig. H1 Fig. H2 Fig. H3 Fig. H4
Fig. H5
Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame or fabric parts.
• The cushions may be washed on the surface only by using mild soap and water or commercial foaming
upholstery cleaner if necessary. If washed, rinse well and hang to dry. Do not machine wash or dry.
• We recommend the use of furniture covers when not in use.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your swing.
• In order to prolong the life and beauty of your swing, we recommend that it be stored in a dry and protected area
during off season periods.
STOP DON’T RETURN TO STORE!
Warning:
To avoid danger of suffocation, always keep
plastic bags or small parts away from babies
and children.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
For further assistance,
please visit us at
[email protected]
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
Warranty
•This product is covered by Courtyard Creations Inc. One–year limited warranty.
•Proof of purchase (dated register receipt) is required for warranty claims.
•It remains the customer’s responsibility for freight and packing charges to and from over service center.