Courtyard Creations KTS889W-WM User manual

ASSEMBLY INSTRUCTIONS
KTS889W-WM
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
PART
NO. MATERIAL CODE PART Q’TY
1
2
3
4
5
1
1
1
1
1
6
27
8
9
10
11
12
13
14
15
16
17
18
19
2
6
12
2
2
6
2
4
1
1
1
2
2
PARTS LIST
STOP DON’T RETURN TO STORE!
PAGE 1 OF 3 COURTYARD CREATIONS INC.
RIGHTARM
LEFTARM
BACK
ASSEMBLY
SEAT
ASSEMBLY
OTTOMAN
BOLT M6*16
BOLT M6*14
BOLT M6*50
BOLT M6*39
WASHER d6.5*D13*1.0
PLASTIC NUT M6*P1.0
PULLEY A
PULLEY B
BOLT CAP
BOLT CAP M6
BOLT CAP M6
HEX.KEY WRENCH 4MM
HEX.KEY WRENCH 6MM
NUT WRENCH 10&13MM
KTS889W-CS01-3
KTS889W-CS01-2
KTS889W-CS03-1
KTS889W-CS02-1
17C02A0755131Y4
17C01A0717072Y4
17C21A0713081Y4
KTS889W-CS04-H
17C33A0706001Y4
17FA05040301-Y4
18000C23001
18000613017
18000613018
18000337004
18000337006
18000337002
17KAA0101----Y4
17KAA0201----Y4
17KAB1101----Y4
Use the correct bolts as indicated. Do not tighten any of the bolts until the lounge chair is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings
required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
!
!
!
!
!SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
Attention:
Make sure that each bolt needed for all steps matches the
corresponding figure to ensure proper assembly.
Step 1:
Place the right arm (#1) onto a non-abrasive surface, such as
a carpet, with its pre-drilled holes accessible. At the rear of the
chair, fasten the seat assembly (#4) to the right arm (#1) by
using bolts (#6) and washers (#10). Keep the bolts loose.
See Figure 1.
Note:
The labels marked “L” and “R” on arms (#1 and #2)
should
coincide with Figure 1 - Figure 3 to ensure proper
assembly.
FIGURE 1
16
6
6
1
4
14
14
10
10
#6 BOLT M6*16
R

STOP DON’T RETURN TO STORE!
PAGE 2 OF 3
Step 2:
At the front of the chair, fasten the seat assembly (#4) to the
right arm (#1) by using bolts (#6 and #7) and washers (#10).
Keep the bolts loose. See Figure 2.
Step 4:
At the front of the chair, fasten the left arm (#2) to the seat
assembly (#4) by using bolts (#6 and #7) and washers (#10).
Keep the bolts loose. See Figure 4.
Step 3:
At the rear of the chair, fasten the left arm (#2) to the seat
assembly (#4) by using bolts (#6) and washers (#10). Keep
the bolts loose. See Figure 3.
FIGURE 2 FIGURE 3
FIGURE 4 FIGURE 5
Step 5 :
Fasten the back assembly (#3) to the seat assembly (#4) by
using bolts (#8), washers (#10), and plastic nuts (#11).
See Figure 5.
16 14
#6 BOLT M6*16
16
#6 BOLT M6*16
#7 BOLT M6*14
16 14
3
4
8
#6 BOLT M6*16 #7 BOLT M6*14
1
4
R
6
6
715
14
14
10
10
6
14
10
2L
4
2L
4
6
715
10
14
50
#8 BOLT M6*50
10 10
11
16

STOP DON’T RETURN TO STORE!
PAGE 3 OF 3
Cleaning and Maintenance
•Wash frame and fabric parts with mild soap and water, rinse
thoroughly, and dry completely. Do not use bleach, acid, or
other solvents on the frame or fabric parts.
•We recommend the use of furniture covers when not in use.
•Inspect and tighten all bolts and fasteners on a regular
basis to ensure the proper performance and safety of your
lounge chair.
•In order to prolong the life and beauty of your lounge chair,
we recommend that it be stored in a dry and protected area
during off season periods.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THESTORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
FIGURE 6
FIGURE 8
FIGURE 7
5
4
12 1310 916
39
#9 BOLT M6*39
Step 6:
Flip the chair upside down. Fasten the ottoman (#5) to the
tracks on the seat assembly (#4). Put the washer (#10) and
pulley B (#13) onto bolt (#9). Insert this through the track
and into pulley A (#12). Then, secure to the ottoman (#5).
Repeat the same procedure for both sides. Make sure that all
of the bolts have been tightened completely and cover them
with bolt caps (#14, #15, and #16). See Figure 6.
Step 7:
Adjust the back assembly (#3) to your desired position.
See Figure 7.
Step 8:
Pull out the ottoman (#5) as needed. See Figure 8.
5
3