Courtyard Creations KUS899F-WM User manual

FIGURE 1
Attention:
Make sure that each bolt needed for all steps matches the
corresponding figure to ensure proper assembly.
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
KUS899F-WM
PAGE 1 OF 2 COURTYARD CREATIONS INC.
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
Step 1:
Place the back assembly (#1) onto a non-abrasive surface,
such as a carpet. Insert the seat assembly (#2) into the back
assembly (#1). See Figure 1.
1
1
2
!
!
!
!
!
PARTS LIST
STOP DON’T RETURN TO STORE!
HEX.KEY WRENCH 4MM
BOLT CAP
BOLT CAP M8
WASHER d6.5*D13*1.0
BOLT M6*35
BACK ASSEMBLY
SEAT ASSEMBLY
LEFT ARM
RIGHT ARM
1
2
3
4
5
6
8
7
9
11
10
12
13
14
15
16
17
1
1
1
1
4
2
8
8
1
1
1
2
2
KUS899F-CS02
KUS899F-CS01
KUS899E-CS03
KUS899E-CS04
17C33A0712001Y4
17C03A0806001Y4
17FA05040301-Y4
WASHER d8.5*D17*1.6
2
17FA08060601-Y4
18000337004
18000319004
17KAA0101----Y4
HEX.KEY WRENCH 6MM
1
17KAA0201----Y4
PART
NO. MATERIAL CODE PART Q’ TY
SEAT CUSHION
PILLOW
61K899FX50001BA
61K899FX00001BA
61K899FY00001BA
61K899FJ00001BA
BOLT M8*16
BOLT M6*65
2
4
17C33A0755001Y4
LEFT BACK CUSHION
RIGHT BACK CUSHION
2

Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or
other solvents on the frame or fabric parts.
•Cushions may be washed on the surface only by using mild soap and water or commercial foaming upholstery cleaner if
necessary. If washed, rinse well and hang to dry. Do not machine wash or dry.
•We recommend the use of furniture covers when not in use.
•Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of your bench.
•In order to prolong the life and beauty of your bench, we recommend that it be stored in a dry and protected area during off
season periods.
FIGURE 2 FIGURE 3
FIGURE 4 FIGURE 5
Step 4:
Fasten both the left arm (#3) and the right arm (#4) to the
back assembly (#1) by using bolts (#7) and washers (#8).
Make sure that all of the bolts have been tightened completely
and cover them with bolt caps (#10 and #11). See Figure 4.
Step 5:
Place the cushions (#14, #15, and #16) and the pillows (#17)
onto the chair. Secure the cushions to the bench by using the
plastic clamps. See Figure 5.
Note:
The labels marked “L” and “R” on the arms (#3 and #4) should
coincide with Figure 3 to ensure proper assembly.
PAGE 2 OF 2
65
#5 BOLT M6*65
35
#7 BOLT M6*35
16
7
810
1
4
3
12
3
L
2
11
6
9
4
R
16
16
17 17
15
14
Step 2:
At the rear of the seat, fasten the seat assembly (#2) to the
back assembly (#1) by using bolts (#5) and washers (#8).
Keep the bolts loose. See Figure 2.
5
10
8
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
Step 3:
Fasten both the left arm (#3) and the right arm (#4) to the seat
assembly (#2) by using bolts (#6) and washers (#9). Keep the
bolts loose. See Figure 3.
STOP DON’T RETURN TO STORE!
#6 BOLT M8*16