Courtyard Creations KUS130B-WM User manual

Attention:
Make sure that all bolts needed for each step matches
the corresponding figure to ensure proper assembly.
Step 1:
Place the right arm (#3) onto a non-abrasive surface,
such as a carpet, with its bracket facing upwards. At the
front of the lounge, insert the rear seat (#1) into the
right arm (#3) and the left arm (#2) by using bolt (#6 and
#7) and washers (#9). Keep the bolts loose.
See Figure 1.
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
FIGURE 1 2
1
KUS130B-WM
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
1
1
1
1
1
6
2
2
2
2
2
1
1
1
1
KUS130B-CS01
KUS130E-CS02
KUS130E-CS03
KUS130E-CS04
KUS130B-CS02
17C33A0706001Y4
17C02A0755131Y4
17C01A0716072Y4
18000C23001
18000337002
17KAA0201----Y4
17KAB1101----Y4
61K130BJ00001BA
61K130BY00001BA
REAR SEAT
LEFT ARM
RIGHT ARM
FRONT SEAT
BACK ASSEMBLY
BOLT M6*16
BOLT M6*14
BOLT M6*45
PLASTIC NUT M6*P1.0
BOLT CAP M6
10
6
BOLT CAP
BOLT CAP M6
HEX.KEY WRENCH 6MM
1
17KAA0101----Y4
HEX.KEY WRENCH 4MM
NUT WRENCH 10&13MM
SEAT CUSHION
PAGE 1 OF 2 COURTYARD CREATIONS INC.
STOP DON’T RETURN TO STORE!
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings
required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
!
!
!
!
!
Note:
The labels marked “L” and “R” on the arm (#2 and #3)
should coincide with Figure 1 to ensure proper
assembly.
9 10
17FA05040301-Y4
WASHER d6.5*D13*1.0
18000337004
18000337006
L
3
6
9
11
6
9
11
6
9
11
R
16
712 14
#6 BOLT M6*16 #7 BOLT M6*14
PILLOW

45
13
10 9
9
8
#8 BOLT M6*45
Step 2:
Insert the rear seat (#1) into the front seat (#4). Make
sure that the spring clips on the rear seat (#1) come
through the holes on the front seat (#4). See Figure 2.
Step 3:
Fasten the back assembly (#5) to the rear seat (#1) by
using bolts (#8), washers (#9), and plastic nuts (#10).
Make sure that all of the bolts have been tightened
completely and cover them with bolt caps (#11, #12 and
#13). See Figure 3.
Cleaning and Maintenance
•Wash frame and fabric parts with mild soap and water,
rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame or fabric parts.
•Cushions may be washed on the surface by only
using mild soap and water or commercial foaming
upholstery cleaner if necessary. If washed, rinse well
and hang to dry. Do not machine wash or dry.
•We recommend the use of furniture covers when not
in use.
•Inspect and tighten all bolts and fasteners on a
regular basis to ensure the proper performance and
safety of your lounge.
•In order to prolong the life and beauty of your lounge,
we recommend that it be stored in a dry and protected
area during the off season periods.
FIGURE 2
1
4
FIGURE 3
FIGURE 4
STOP DON’T RETURN TO STORE!
PAGE 2 OF 2
5
1
17
18
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
TO THERETAILER.PRODUCT
Step 4:
Place the seat cushion (#17) and the pillow (#18) onto
the lounge. Secure the cushion to the lounge by using
the plastic clamps. See Figure 4.