Courtyard Creations KSS100V-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
KSS100V-WM
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
8
2
10
1
1
1
1
2
1
1
1
1
1
1
2
2
2
2
2
1
2
4
2
8
10
4
18
4
KSS1008-CS01
KSS1008-CS02
KSS1004-CS02
KSS1008-CS04
KSS1008-CS05
KSS1004-CS03
KSS1004-CS04
KSS1008-CS08
17C01A0844061Y4
17C01A0756131Y4
17C01A0716072Y4
17C17A1306001Y4
17FA05040301-Y4
17FA08060601-Y4
1800C23001
17D03A040401-Y4
1800337002
17KAB1101----Y4
17KAA0201----Y4
61K100VC00001BA
61K100VC50001BA
61K100VJ00001BA
61K100VG00008IA
61K100VQ00008IA
KSS1004-CS05
KSS100V-CS01
KSS1004-CS07
KSS1004-CS08
SEAT BASE
SEAT BASE
MIDDLE SEAT
BACK A
BACK B
MIDDLE LEG
LEG
SEAT CROSS BRACE
BOLT M8*95
BOLT M6*48
BOLT M6*45
SCREW ST4.2*16
WASHER d6.5*D13*1.0
WASHER d8.5*D17*1.6
PLASTIC NUT M6*P1.0
JAM NUT M8*1.25
BOLT CAP M6
NUT WRENCH 10 & 13MM
HEX.KEY WRENCH 6MM
LEFT CUSHION
RIGHT CUSHION
PILLOW
COVER BAG
COVER
UMBRELLA
LOWER CENTER PLUG
BOTTOM POLE
TABLE TOP
Do not discard any of the packaging until you have checked that you have all the parts and pack of fittings.
Keep children away during assembly. This item contains small parts which can be swallowed by children. Children should always
be under direct adult supervision while using the product.
Retain the assembly instructions for future reference.
Please quote following FQC NO. when contacting service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
COURTYARD CREATIONS INC.
!
!
!
!
STOP DON’T RETURN TO STORE!
PAGE 1 OF 5

STOP DON’T RETURN TO STORE!
PAGE 2 OF 5
95
#9 BOLT M8*95
Step 1
Step 2
Step 3
45
#11 BOLT M6*45
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
You will need the following tools
- Phillips Screwdriver (Not Included)
- Nut Wrench (See Part #18)
- Hex.Key Wrench (See Part #19)
Attention:
Make sure that each bolt needed for
all steps match the corresponding
figure to ensure proper assembly.
Step 1:
Fasten the middle leg (#6) in the
center of the middle seats (#3) by
using bolts (#9), washers (#14), and
jam nuts (#16). Do not fully tighten
the bolts yet. See Figure 1.
NOTE:
The labelled arrow marks on the
middle seats (#3) should be facing
upwards to ensure proper assembly.
Step 2:
Insert the seat bases (#2) into the
middle seats (#3). Please ensure that
their holes align. Do the same
procedure for both sides.
See Figure 2.
NOTE:
The labelled arrow marks on the seat
bases (#2) should match those on the
middle seats (#3) to ensure proper
assembly.
Step 3:
Insert the seat bases (#2) into the seat
bases (#1). Make sure the spring clips
on the seat bases (#2) come through
the holes on the seat bases (#1).
See Figure 3.
NOTE:
The labelled arrow marks on the seat
bases (#1 and #2) should be facing
upwards to ensure proper assembly.
Step 4:
Insert the connector tabs on the seat
bases (#1) into the legs (#7). Make
sure the spring clips on the seat bases
(#1) come through the boles on the
legs (#7). See Figure 4 - Step 1.
Fasten the middle seats (#3) to the
seat bases (#2) by using screws (#12).
See Figure 4 - Step 2.
Fasten the middle leg (#6) to the legs
(#7) by using bolts (#11) and washers
(#13). See Figure 4 - Step 3.

STOP DON’T RETURN TO STORE!
PAGE 3 OF 5
48
#10 BOLT M6*48
45
#11 BOLT M6*45
FIGURE 5
FIGURE 6
FIGURE 7
Step 5:
Fasten the back A (#4) to the middle seat
(#3) by using bolts (#10). See Figure 5.
NOTE:
The label mark “A” on back A (#4) should be
facing upwards to ensure proper assembly.
Step 6:
Fasten the seat cross brace (#8) to the back
A (#4) and the seat base (#1) by using bolts
(#11), washers (#13) and plastic nuts (#15).
Repeat Figure 5 and Figure 6 for the
remaining back A (#4) and backs B (#5).
See Figure 6 and Figure 7.
Completely tighten all bolts and cover them
with bolt caps (#17).
NOTE:
The labelled marks “A and B” on backs A (#4)
and backs B (#5) should be facing upwards
to ensure proper assembly.

STOP DON’T RETURN TO STORE!
PAGE 4 OF 5
Loose
up
down
Tighten
press
FIGURE 8
FIGURE 9
FIGURE 10
FIGURE 11
Step 7:
Insert the bottom pole (#27) into the upper
center plug on the table top (#28).
See Figure 8.
NOTE:
The labelled arrow mark on the bottom pole
(#27) should coincide with Figure 8 to ensure
proper assembly.
Step 8:
Insert the bottom pole (#27) into the lower
center plug (#25). See Figure 9.
Step 9:
Tighten the lower center plug (#25), then,
press down the button on the upper center
plug of the table top (#28) and insert the upper
center plug on the table top (#28) into the
lower center plug (#25). See Figure 10.
Step 10:
Insert the assembled table with bottom pole
into the hole in the middle leg (#6).
See Figure 11.

STOP DON’T RETURN TO STORE!
PAGE 5 OF 5
FIGURE 12
FIGURE 13
FIGURE 14
Step 11:
Insert the umbrella (#26) into the bottom pole (#27).
Make sure the spring clips on the umbrella (#26) come
through the holes on the bottom pole (#27).
See Figure 12.
Step 12:
Put the cushions (#20, #21) and the pillows (#22) on to
the lounge. Secure the cover bag (#23) on to the seat
base (#1) by using the velcro. See Figure 13.
NOTE :
To prevent your lounge from the rust, you can use the
cover (#24) provided in the cover bag (#23) when not in
use, and please remember to remove the umbrella and
bottom pole at first.
NOTE :
To turn the lounge into a bed, pressing the spring buttons
on the seat cross braces (#8). The seat cross braces have
two pre-drilled holes that allow the backs to recline into two
positions. See Figure 14.
Special Warnings:
• Please inspect this lounge before each use.
•Position the lounge on level ground and no less than six
feet away from any obstruction such as, fences, garages,
houses, overhanging branches, laundry lines, electrical
wires, etc.
• Ensure the tightness of all nuts and bolts on a regular
basis.
• The manufacturer will not accept responsibility for
unauthorized repairs and/or modifications made to the
lounge.
• Weight limit is 500 lbs.
Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse
thoroughly, and dry frame completely. Do not use bleach,
acid, or other solvents on the frame parts.
• Cushions may be washed on the surface only by using
mild soap and water or commercial foaming upholstery
cleaner if necessary. If washed, rinse well and hang dry.
Do not machine wash or dry.
• We recommend the use of furniture covers when not in use.
• Please inspect and tighten all bolts or fasteners on a
regular basis to ensure proper performance and safety of
your lounge.
• In order to prolong the life and beauty of your lounge, we
recommend that it be stored in a dry and protected area during off season periods.
Missing A Part?
No Need To Go Back To
TheStore!
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
Call Toll Free
TEL: [phone]
FAX: [phone]
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free
TEL: [phone]
FAX: [phone]
PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
SHOULD YOU NOTLOCATE ALL OF THE ABOVE PARTS, PLEASE INSPECTALL
PACKING MATERIAL FOR ANY SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED IN SHIPMENT.
SHOULDYOU EXPERIENCEANYDIFFICULTY DURING ASSEMBLYOR IF ANY
PARTIS MISSING OR DAMAGED,PLEASE CALL THE HELP LINE 1-877-539-7436
BEFORERETURNING THEITEM TO THE STORE.
PLEASE PROVIDE THEFOLLOWING INFORMATION:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST
SHOWN ON ASSEMBLY INSTRUCTIONS.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS PRODUCT
TO THERETAILER.
2423