Courtyard Creations KTS889F-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
PARTS LIST
KTS889F-WM
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
1
2
3
4
5
6
7
1
1
1
1
8
9
8
10
10
2
8
2
1
Do not discard any of the packaging until you have checked that you have all the parts and pack of fittings.
Keep children away during assembly. This item contains small parts which can be swallowed by children.
Children should always be under direct adult supervision while using the product.
Retain the assembly instructions for future reference.
Please quote following FQC NO. when contacting service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
PAGE 1 OF 2 COURTYARD CREATIONS INC.
!
!
!
!
STOP DON’T RETURN TO STORE!
FIGURE 1
Attention:
Make sure that each bolt needed for all steps
match the corresponding figure to ensure proper
assembly.
KTS889E-CS01
KTS889E-CS02
KTS889F-CS01
62KTS889FH101
17C33A0706001Y4
17C01A0712001Y4
17FA05040301-Y4
1800337004
1800337001
17KAA0101----Y4
LEFT ARM
RIGHT ARM
SEAT ASSEMBLY
SUPPORT
BOLT M6*16
BOLT M6*35
WASHER d6.5*D13*1.0
BOLT CAP
BOLT CAP M6
HEX. KEY WRENCH 4MM
STEP 1:
Place the right arm (#2) onto a non-abrasive
surface, such as a carpet. At the front of the bench,
fasten the seat assembly (#3) to the arms (#1 and
#2) by using bolts (#5) and washers (#7). Keep
the bolts loose. See Figure 1.
5
5
7
7
8
8
NOTE:
The labels marked “L” and “R” on the arms (#1
and #2) should coincide with Figure 1 to ensure
proper assembly.
R
L
16
#5 BOLT M6*16
1
2
3

PAGE 2 OF 2
STOP DON’T RETURN TO STORE!
FIGURE 2
FULL ASSEMBLY
FIGURE 3
16
#5 BOLT M6*16
STEP 2:
At the rear of the bench, fasten the support (#4)
to the arms (#1 and #2) by using bolts (#5) and
washers (#7). Keep the bolts loose.
See Figure 2.
STEP 3:
Turn the bench to its upright position. At the back of
the bench, fasten the seat assembly (#3) to the arms
(#1 and #2) by using bolts (#6) and washers (#7).
Make sure that all of the bolts have been tightened
completely and then cover them with bolt caps (#8
and #9). See Figure 3.
STEP 4:
See Full Assembly.
Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and
water, rinse thoroughly, and dry frame completely.
Do not use bleach, acid, or other solvents on the
frame and fabric parts.
• We recommend the use of furniture covers when
not in use.
• Please inspect and tighten all bolts or fasteners on
a regular basis to ensure proper performance and
safety of you bench.
• In order to prolong the life and beauty of your
bench, we recommend that it be stored in a dry and
protected area during off season periods.
Missing A Part?
No Need To Go Back To
TheStore!
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
Call Toll Free
TEL: [phone]
FAX: [phone]
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
SHOULD YOU NOTLOCATE ALL OF THE ABOVE PARTS, PLEASE INSPECTALL
PACKING MATERIAL FOR ANY SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED IN SHIPMENT.
SHOULD YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTIS MISSING OR DAMAGED,PLEASE CALL THE HELP LINE 1-877-539-7436
BEFORERETURNING THE ITEM TO THE STORE.
PLEASE PROVIDE THEFOLLOWING INFORMATION:
1- MODEL NUMBER OF THEPRODUCT.
2- PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST
SHOWN ON ASSEMBLY INSTRUCTIONS.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS PRODUCT
TO THERETAILER.
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free
TEL: [phone]
FAX: [phone]
#6 BOLT M6*35
35
4
5
5
7
7
8
8 9
6
7
1
2
343
1
2