Courtyard Creations SVS20P8 User manual

KVS941Z
SVS20P8
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
AUGUSTA ALL-WEATHER WICKER 3 PERSON
LEFT ARM CUSHION SOFA AND RIGHT ARM LOVESEAT
PAGE 1 OF 6
E-3
Use the correct bolts as indicated. Do not tighten any of the bolts until the chair is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO
TEL: [phone]
FAX: [phone]
PARTS LIST
1
4
1
3
5
1
1
1
3
KVS941A-CS03-1
KVS941A-CS02-1
KVS941Z-CS01-1
17C40A0710001YX
17C40A0712001YX
17LA07121----YX
Step 1:
Fasten the plastic leg cap (#6) to the back assembly (#1)
by using washer (#8) and nut (#7). See Figure 1.
FIGURE 1
BACK ASSEMBLY
SEAT ASSEMBLY
ARM ASSEMBLY
BOLT M6*30
BOLT M6*35
HEX. KEY WRENCH 4MM
HEX. KEY WRENCH 6MM
BACK CUSHION
SEAT CUSHION
COURTYARD CREATIONS INC.
PART
NO. MATERIAL CODE PART Q’TY
1
2
13
4
5
6
8
11
12
13
"
"
"
"
"
47
4
28000221046
PLASTIC LEG CAP
17KAA0101----Y4
17KAA0201----Y4
61K941ZX00001BA
61K941ZY00001BA
NUT M8
10
9
3
17FC08030801-YX
WASHER d8.5*D12*2.1
17KAC3101----Y3
HEX. KEY WRENCH 10MM
MBLY
1
6
6
7
8
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.

12
3
PAGE 2 OF 6
FIGURE 2
Step 2:
Fasten the plastic leg caps (#6) to the arm assembly
(#3) by using washers (#8) and nuts (#7).
See Figure 2.
Step 3:
Fasten the plastic leg cap (#6) to the seat assembly
(#2) by using washer (#8) and nut (#7).
See Figure 3.
FIGURE 3
55
5
5
Step 4:
Place the arm assembly (#3) onto a non-abrasive
surface, such as a carpet. Fasten the seat assembly
(#2) to the arm assembly (#3) by using bolts (#5).
Keep the bolts loose. See Figure 4.
Step 5:
Fasten the back assembly (#1) to the seat assembly
(#2) and arm assembly (#3) by using bolts (#4 and #5).
Keep the bolts loose. See Figure 5.
5
5
4
FIGURE 4 FIGURE 5
E-3
6
63
IGURE
3
6
2
6
8
7
E
4
2
3
6
7
8
12
Step 6:
Fasten the back assembly (#1) to the seat assembly (#2)
by using bolt (#5). Make sure that all of the bolts have
been tightened completely. See Figure 6.
5
FIGURE 6
35
30
#5 BOLT M6*35
#4 BOLT M6*30

PAGE 3 OF 6
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
For further assistance,
please visit us at
[email protected]
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL OF THE PARTS, MAKING SURE THAT
YOU HAVE ALL OF THE PARTS LISTED.
IF YOU DO NOT LOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTS THAT MAY HAVE BECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCE ANY DIFFICULTY DURING ASSEMBLY OR IF ANY
PARTS ARE MISSING OR DAMAGED, CALL THE HELP LINE AT
1-877-539-7436 BEFORE RETURNING THIS ITEM TO THE STORE.
PROVIDE THE FOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THE PRODUCT.
2-PART NUMBER AND MATERIAL CODE OF THE PART FROM THE PARTS
LIST.
MOST PROBLEMS CAN BE RESOLVED WITHOUT RETURNING THIS
PRODUCT TO THE RETAILER.
Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not
use bleach, acid, or other solvents on the frame or fabric parts.
• The cushions may be washed on the surface only by using mild soap and water or a commercial
foaming upholstery cleaner if necessary. If washed, rinse well and hang to dry. Do not machine wash
or dry.
• We recommend the use of furniture covers when not in use.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and
safety of your chair.
• In order to prolong the life and beauty of your chair, we recommend that it be stored in a dry and
protected area during off season periods.
E-3
Warranty
• This product is covered by Courtyard Creations Inc.'s one–year limited warranty.
• Proof of purchase (dated register receipt) is required for warranty claims.
• It remains the customer’s responsibility for freight and packing charges to and from the service center.
Step 7:
Turn the chair to its upright position. Place the cushions
(#12 and #13) onto the chair. You can adjust the leveler
on the plastic leg caps (#6) to keep the chair even when it
is not stable. See Figure 7.
FIGURE 7
6
12
12
12
13
13
13
Sofa is for sitting purposes only. Standing on or misuse of sofa may result in damage or injury. Weight limit
750 lbs (340.5kg). Not intended for commercial use.

Use the correct bolts as indicated. Do not tighten any of the bolts until the chair is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
"
"
"
"
"
KVS941F
PARTS LIST
1
4
1
31
1
1
2
KVS941D-CS03-1
KVS941D-CS02-1
KVS941F-CS01-1
17C40A0710001YX
17LA07121----YX
Step 1:
Fasten the plastic leg cap (#6) to the back assembly (#1)
by using washer (#8) and nut (#7). See Figure 1.
FIGURE 1
BACK ASSEMBLY
SEAT ASSEMBLY
ARM ASSEMBLY
BOLT M6*30
HEX. KEY WRENCH 4MM
HEX. KEY WRENCH 6MM
BACK CUSHION
SEAT CUSHION
PART
NO. MATERIAL CODE PART Q’TY
1
2
13
4
5
6
8
11
12
13
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
47
4
28000221046
PLASTIC LEG CAP
17KAA0101----Y4
17KAA0201----Y4
61K941FX00001BA
61K941FY00001BA
NUT M8
10
9
2
5
17C40A0712001YX
BOLT M6*35
17FC08030801-YX
WASHER d8.5*D12*2.1
17KAC3101----Y3
HEX. KEY WRENCH 10MM
IGURE
1
16
6
78
PAGE 4 OF 6
SERVICE CENTER TOLL FREE NO
TEL: [phone]
FAX: [phone]
COURTYARD CREATIONS INC.
E-3
EMBLY
MBLY
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.

1
2
1
3
2
2
3
6
2
6
6
3
5
5
5
5
4
FIGURE 2
Step 2:
Fasten the plastic leg caps (#6) to the arm assembly
(#3) by using washers (#8) and nuts (#7).
See Figure 2.
Step 3:
Fasten the plastic leg cap (#6) to the seat assembly
(#2) by using washer (#8) and nut (#7).
See Figure 3.
Step 4:
Place the arm assembly (#3) onto a non-abrasive
surface, such as a carpet. Fasten the seat assembly
(#2) to the arm assembly (#3) by using bolts (#5).
Keep the bolts loose. See Figure 4.
Step 6:
Fasten the back assembly (#1) to the seat assembly (#2)
by using bolt (#4). Make sure that all of the bolts have
been tightened completely. See Figure 6.
Step 5:
Fasten the back assembly (#1) to the seat assembly
(#2) and arm assembly (#3) by using bolts (#4 and #5).
Keep the bolts loose. See Figure 5.
FIGURE 3
55
4
FIGURE 4 FIGURE 5
FIGURE 6
6
8
7
6
87
PAGE 5 OF 6
E-3
35
30
#5 BOLT M6*35
#4 BOLT M6*30

PAGE 6 OF 6
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
For further assistance,
please visit us at
[email protected]
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL OF THE PARTS, MAKING SURE THAT
YOU HAVE ALL OF THE PARTS LISTED.
IF YOU DO NOT LOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTS THAT MAY HAVE BECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCE ANY DIFFICULTY DURING ASSEMBLY OR IF ANY
PARTS ARE MISSING OR DAMAGED, CALL THE HELP LINE AT
1-877-539-7436 BEFORE RETURNING THIS ITEM TO THE STORE.
PROVIDE THE FOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THE PRODUCT.
2-PART NUMBER AND MATERIAL CODE OF THE PART FROM THE PARTS
LIST.
MOST PROBLEMS CAN BE RESOLVED WITHOUT RETURNING THIS
PRODUCT TO THE RETAILER.
Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame or fabric parts.
• The cushions may be washed on the surface only by using mild soap and water or a commercial foaming
upholstery cleaner if necessary. If washed, rinse well and hang to dry. Do not machine wash or dry.
• We recommend the use of furniture covers when not in use.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your chair.
• In order to prolong the life and beauty of your chair, we recommend that it be stored in a dry and protected
area during off season periods.
E-3
Warranty
• This product is covered by Courtyard Creations Inc.'s one–year limited warranty.
• Proof of purchase (dated register receipt) is required for warranty claims.
• It remains the customer’s responsibility for freight and packing charges to and from the service center.
Step 7:
Turn the chair to its upright position. Place the cushions
(#12 and #13) onto the chair. You can adjust the leveler
on the plastic leg caps (#6) to keep the chair even when it
is not stable. See Figure 7.
FIGURE 7
6
I
G
U
R
E
7
12 12
13
13
Sofa is for sitting purposes only. Standing on or misuse of sofa may result in damage or injury. Weight limit
500 lbs (227kg). Not intended for commercial use.