Crestron CCS-UC-1-X User manual

The Crestron® CCS-UC-1-X provides video conference capabilities to a
conference room.
In the Box
1 CCS-UC-1-X, Crestron Mercury® X Tabletop UC System
Additional Items
1 Cable, USB 2.0, A - Micro B, 6 ft (1.83 m) (P/N 2047803)
1 Cable, HDMI®, Thin, 6 ft (1.8 m) (P/N 6508218)
1 Cable, CAT5e, RJ-45 Male - RJ-45 Male, 12 ft (3.66 m) (P/N
2033988)
1 Retention Plate, Cable (P/N 2047908)
3 Tie Wrap (P/N 2047935)
1 Power Pack, 24 VDC, 2.5 A, 100-240 VAC (P/N 2045873)
1 Power cord (varies by location)
Install the Cable Retention Plate
The cable retention plate provides tie-down points for cables that are
connected to the device.
Remove the adhesive backing from the cable retention plate and install it
on the underside of the CCS-UC-1-X as shown in the following diagram.
CAUTION: When turning over the device, place the device on a soft
surface to avoid damage.
NOTES:
lIf the CCS-UCA-SMK swivel mount kit is to be used, use the
cable retention bracket included with the CCS-UCA-SMK. For
details, refer to the CCS-UCA-SMK DO Guide (Doc. 7882) at
www.crestron.com/manuals.
lBefore securing cables, ensure the cable retention plate is firmly
attached.
CCS-UC-1-X Quick Start
1

Connect
Make connections to the CCS-UC-1-X.
Make Connections
When making connections, it is highly recommended to use the cables
shipped with the device. The cables and accessories have been designed so
that a service loop can be implemented prior to the cables leaving the
chassis body of the device (if necessary). If an extension option is required,
Crestron solutions should always be used and can be found under
MODELS & ACCESSORIES on the Crestron Mercury Xweb page.
CCS-UC-1-X Quick Start
2

CCS-UC-1-X Quick Start
3

Route Cables
CCS-UCA-SMK Swivel Mount Kit
If the CCS-UCA-SMK swivel mount kit is used in the installation, refer to
the CCS-UCA-SMK DO Guide for installation instructions (Doc. 7882).
NOTE: Do not route the HDMIand USB cables through the swivel tube.
USBand HDMICables
Insert the included USB and HDMI cables into the appropriate cable
channels on the underside of the CCS-UC-1-X.
NOTE:If the system design dictates that the USB and HDMI Input
cables should not exit through the front but at the rear with all other
cables, the USB and HDMIinput cables should be bundled and secured
to the cable retention plate on the underside of the CCS-UC-1-X. Make
sure to leave enough cable for a 2- to 3- inch service loop before exiting
the rear of the device.
Power,Ethernet, HDBaseT, and Other Cables
Bundle the Ethernet, HDBaseT, and other cables together and use a
provided tie wrap to secure the bundle to one of the positions on the cable
retention plate.
Configure Settings
For details on configuring the device, refer to the CCS-UC-1 Product
Manual (Doc. 7844).
CCS-UC-1-X Quick Start
4

Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, and Crestron Mercury are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
HDBaseT is either a trademark or registered trademark of the HDBaseT Alliance in
the United States and/or other countries. HDMI and the HDMI logo are either
trademarks or registered trademarks of HDMI Licensing LLC in the United States
and/or other countries. Other trademarks, registered trademarks, and trade names
may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and
names of others. Crestron is not responsible for errors in typography or photography.
©2019 Crestron Electronics, Inc.
Doc ID 8453A
(2053534)
11/14/19
CCS-UC-1-X Quick Start
5