Crestron UC-M70-NC-Z User manual

The UC-M70-NC-Z Crestron Flex tabletop conferencing system provides
a large room conference solution for use with Zoom Rooms® software. It
supports up to three video displays and features a Crestron Flex
tabletop conference device and UC bracket assembly.
Minimum Requirements:
lA Zoom Rooms certified USB Camera (not included).
lA video display (not included) connected to the UCEngine. A second
display is optional.
lA Zoom Rooms account or activation code (not included).
In the Box
Tabletop Conference Device
1 Tabletop Conference Device, Zoom Rooms Software
(6508227)
1 Cable, CAT5e, RJ-45 - RJ-45, 12 ft (3.7 m) (2033988)
1 Cable Retention Plate (2047908)
3 Tie Wrap (2047935)
UC Bracket Assembly
1 UC Bracket Assembly with UC Engine and HDMI® content
ingest (UC-BRKT-200-S-Z-ASSY, 6512690)
2 Anchor, Drywall, Plastic, 3/8 in. x 1/2 in. (9.5mm x
12.7mm) (2052565)
1 Key, Anchor (4529654)
2 Screw, 8-AB x 1-1/2 in. (38.1 mm), Pan Head, Combo
(2052567)
4 Tie Wrap (2047935)
Additional Items
1 Microphone pod (6508084)
1 Cable, CAT5e, RJ-45 - RJ-45, 7 ft (2.1 m) (6509924)
1 Cable, DisplayPort™ to HDMI, 6 ft (1.8 m) (6508282)
1 Cable, HDMI, 20 ft (6.1 m) (6503567)
1 Cable, HDMI, 6 ft (1.8 m) (6512150)
1 Cable, USB 2.0, A - Micro-B, 6 ft (1.8 m) (6510947)
1 Cable, USB Extension, USB Type A Male-to-Female, 15 ft
(4.6m) (6508260)
1 Power supply (6500187)
1
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

Mount Devices
Mount the UC Bracket Assembly
Mount the UC Bracket Assembly to VESA® compliant display devices, a
wall, or other building structure. Anchors and screws are supplied for
installation on walls with 3/8 in. (9.5mm) to 3/4 in. (19mm) thickness.
CAUTION: Preinstalled screws may protrude from the back of the
UC Bracket Assembly. Exercise caution when handling the UC
Bracket Assembly to avoid scratching or damaging surfaces.
NOTE: The integrated cable tie wraps are reusable. Avoid damaging
the cable tie wraps.
Install the Cable Retention Plate
The included cable retention plate provides tie-down points for cables
that connect to the Crestron® conference device.
Remove the adhesive backing from the cable retention plate and install
the plate on the underside of the conference device as shown in the
following diagram. Ensure the cable retention plate is firmly attached
before securing cables.
CAUTION: When turning over the device, place the device on a soft
surface to avoid damage.
NOTE: If a swivel mount kit (CCS-UCA-SMK) is to be used, use the
cable retention bracket included with the swivel mount kit as
described in the CCS-UCA-SMK DO Guide (Doc. 7882).
2
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

Connect
Identify the UC Bracket Assembly
The UC Bracket Assembly is available in two models. Identify the model included with your Crestron Flex system. Tap or click the corresponding
image below to navigate to the appropriate connection instructions.
UC Bracket Assembly with HD-CONV-USB-200 UC Bracket Assembly with HD-CONV-USB-300
3
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

System Overview
For UC Bracket Assembly with HD-CONV-USB-200
When connections are complete, the system appears as shown below. Refer to Make Connections for detailed connection instructions.
4
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

For UC Bracket Assembly with HD-CONV-USB-300
When connections are complete, the system appears as shown below. Refer to Make Connections for detailed connection instructions.
5
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

Make Connections
NOTE: For reference, the UC Bracket Assembly is shown with the HD-CONV-USB-200 in the following connection diagrams. Unless otherwise
indicated in this guide, the connections remain the same for the UC Bracket Assembly with HD-CONV-USB-200 and HD-CONV-USB-300.
1. Make UC Engine connections as shown in the following illustration.
6
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

2. Connect displays to the UC Engine.
7
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

3. Connect a camera (not included) to the UC Engine as shown in the image below. Do not connect the camera to any of the other USB ports.
8
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

4. Connect a laptop to the HD-CONV-USB-200 or HD-CONV-USB-300.
5. Bundle the cables to the bracket assembly with the integrated cable tie wraps. The cable tie wraps are reusable.
9
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

Bundle Cables
Bundle the cables together and use a provided tie wrap to secure the
bundle to one of the positions on the cable retention plate at the rear of
the device. Avoid bundling power and data cables together.
Configure
Apply Power
Press the power button on the bottom of the UC Engine and apply
power to all of the other devices in the system.
Configure the Conference Device
To configure the conference device to operate in Zoom Rooms Video
mode:
1. On a computer, enter the IP address displayed on the conference
device into a web browser.
NOTES:
lThe device and computer must be on the same network switch
and VLAN.
lA login with administrative rights for the device is required.
2. Enter the following information in the appropriate fields:
lUC-Engine Address: Enter the IP address or hostname of the UC
Engine.
NOTE: The hostname is printed on a label affixed to the UC
Engine.
lUC-Engine Port: By default, port number 49500 is used. If a
different port number has been configured on the UC Engine,
enter that port number instead.
lUC-Engine Admin Username: Enter the username for the UC
Engine. The default username is “admin”.
lUC-Engine Admin Password: Enter the login password for the UC
Engine. The default password is “crestron”.
3. Select Save Changes.
10
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

4. On the UC Engine, connect a USB keyboard and mouse (not included)
to sign in to the Zoom Rooms service with an activation code or sign-
in credentials (email and password).
NOTE: The Zoom Rooms Video mode allows sign-in only through
the UC Engine. Therefore, to view the following instructions, use
the conference room display connected to the UC Engine.
lActivation Code:
a. Select Enter Activation Code.
b. Enter the 16-digit activation code provided by the
ITadministrator managing the Zoom portal to activate the
Zoom Room assigned to the activation code. The Zoom Rooms
Conference Room screen is shown on the display.
lSign In:
a. Select Sign In.
b. Enter the Zoom Room credentials and tap Sign In.
c. Select the conference room name from the list and tapNext.
The Zoom Rooms Conference Room screen is shown on the
display.
5. Visit the Zoom portal, navigate to Room Management >Zoom
Rooms >(Room Name) >Room Settings >Rooms Profile >Devices.
6. Enable the Use Windows-attached Zoom Rooms Controller with
specific Windows Monitor Hardware IDs setting. Then, copy and
paste the following string into the text field:
Crestron:TCT009A,Crestron:FUN0216,Crestron:FUN0270
7. On the conference device, tap Settings. If a password is required,
enter the password (the default password is "1234"). The Settings
screen is displayed.
8. Tap Microphone and select the conference device as the source.
9. Tap Speaker and select the conference device as the source.
10. Tap Home to exit.
Configure the System
Refer to the Crestron Flex Unified Communications Solution product
manual to configure system features.
For detailed information on using Zoom Rooms, refer to the Zoom
Rooms Help Center.
Visit the Product Page
Scan the QR code to visit the product page.
UC-M70-NC-Z
www.crestron.com/model/6513794
11
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software

Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software
is licensed to Crestron dealers, CSPs, and end-users under a separate End-User
License Agreement. Both of these Agreements can be found on the Crestron website
at www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information,
visit www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. HDMI is either
a trademark or registered trademark of HDMI Licensing LLC in the United States
and/or other countries. DisplayPort and VESA are either trademarks or registered
trademarks of Video Electronics Standards Association in the United States and/or
other countries. Zoom Rooms is either a trademark or registered trademark of Zoom
Video Communications, Inc. in the United States and/or other countries. Other
trademarks, registered trademarks, and trade names may be used in this document
to refer to either the entities claiming the marks and names or their products.
Crestron disclaims any proprietary interest in the marks and names of others.
Crestron is not responsible for errors in typography or photography.
©2024 Crestron Electronics, Inc.
Doc. 9474A
01/25/24
12
UC-M70-NC-Z QuickStart
Crestron Flex Tabletop Large Room Conference System for Zoom Rooms® Software