Crestron AirMedia AM-101 User manual

DO GUIDE
AM-101
AirMedia®Presentation Gateway
DO Install the Device
The AM-101 can be mounted on a wall or placed onto a at surface.
NOTE: If wall mounting is not required, place the AM-101 on a at, even surface.
Ensuring Proper Ventilation
The AM-101 should be used in a well-ventilated area. To prevent overheating, do not operate this
product in an area that exceeds the environmental temperature range for this product. Consider using
forced air ventilation to reduce overheating. Consideration must be given if the device is installed in a
closed or multiunit rack assembly, since the operating ambient temperature of the environment may be
greater than the room ambient temperature. Contact with thermal insulating materials should be avoided
on all sides of the unit.
Mounting to a Wall
The AM-101 can be mounted using the included wall-mount bracket. Refer to the following illustration for
installation instructions.
DO Connect the Device
Make the necessary connections as called out in the illustration that follows. When making connections
to the AM-101, use Crestron®power supplies for Crestron equipment. Apply power after all connections
have been made.
NOTE: Typical installation uses only the HDMI®OUT or the VGA OUT-AUDIO OUT connection.
DO Congure the Device
While the AM-101 can be used right out of the box, the device can be further customized with its web
interface. For details on conguring the AM-101, refer to the AM-101 Supplemental Guide (Doc. 7918) at
www.crestron.com/manuals.
DO Share a Presentation
This section provides instructions on sharing a desktop on a display device. For instructions on remotely
viewing a shared desktop, refer to “DO View a Presentation Remotely.”
Make all connections as described in “DO Connect the Device” above. The connected display device
shows the AM-101 welcome screen.
Mobile devices can share their content using the Crestron AirMedia app or the Crestron Pinpoint™
mobile app, which are available for iOS®and Android™ devices. Both apps may be used for full screen
sharing on devices running Android 5.0 Lollipop and above. Download the latest version of these apps
from the App Store®app in iTunes®software or from the Google Play™ store.
PC and Mac®computers (hereafter referred to as “computer”) can download a client application from
the AM-101 that can be used to share a desktop. The computer should be able to access the AM-101
over the network.
1. Open a web browser on the computer, and navigate to the web address or IP address
displayed on the top left of the AM-101 welcome screen. The download screen is displayed.
2. Click the Download icon for the computer’s operating system to download the client
application. The client application requires no installation. The application can either be saved
and run locally, or be run from the Internet.
NOTE: When used on a Mac, the AirMedia client application must be run from within the disk
image le. Do not drag the application out of the disk image le.
Share the Computer Desktop
Once the client application is downloaded, content can be shared.
1. Run the client application. The Enter Code (Enter Passcode on Mac) screen is displayed.
Enter Code (L-R, Windows and Mac)
2. Enter the code displayed on the AM-101 welcome screen and click OK (CONFIRM on Mac).
The client application establishes a connection between the computer and the AM-101 while
displaying the presentation control screen on the computer.
The contents of the computer screen are shown on the display connected to the AM-101.
Crestron AirMedia Controls (L-R, Windows and Mac)
3. Direct the presentation with the following controls:
• Click A to stop showing the computer’s screen.
• Click H to start showing the computer’s screen.
• Click b to freeze the computer’s screen.
• Hover over to show a volume slider control and drag the slider to raise or lower the
volume. Click to mute the audio output.
• Click to unmute the audio output.
• Click Details for additional controls and information.
○The Video Source control allows the user to select between the primary video
source and the extended video source.
○The Screen Position control sets the position of displayed content on a remote
viewer’s display.
○The Remote View switch enables and disables remote viewing of presented
content.
○Information about the connected user, the name of the receiver, the IP address, and
the access code are displayed.
○Click Xto close the client application and the connection between the computer and
the AM-101. On a Mac, click to close the client application and the AM-101.
○Click - to minimize the presentation control screen. On a Mac, click to minimize
the presentation control screen.
Other Functions
Click Details to control remote viewing and video performance. For details, refer to the AM-101
Supplemental Guide (Doc. 7918) at www.crestron.com/manuals.
DO Check the Box
QUANTITY PRODUCT PART NUMBER
1Bracket, Wall Mount 2038249
1 Kit, Mounting Hardware 2039564
1 Power Pack, 5 Vdc 2038069
SERVICE:
Not used
LAN:
10BASE-T/100BASE-TX
Ethernet to LAN
VGA OUT:
To display’s VGA input
(use with AUDIO OUT)
HDMI®OUT:
To display’s HDMI input
AUDIO OUT:
To display’s audio input
(use with VGA OUT)
5V 2.6A:
From included power pack
Attach the AM-101 to the
wall-mount bracket using
the two screws and washers
(included)
Wall-mount bracket

DO GUIDE DOC. 7930D (2047278) 12.17
Specications subject to change without notice.
DO View a Presentation Remotely
This section provides instructions on remotely viewing a shared desktop. For instructions on sharing a desktop, refer to “DO Share a Presentation” on the
previous page.
If Remote View is enabled, audience members can view desktop images via the AM-101’s built-in web server. Perform the following steps to remotely view
images:
1. Open a web browser on a remote computer, and navigate to the web address or IP address supplied by the user or users that are sharing their
desktops. The download screen is displayed.
2. Click Remote View. The shared desktop is displayed in the web browser as a web page.
3. Use the following buttons when viewing the AM-101’s output in a web browser:
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs,
and end-users under a separate End-User License Agreement. Both of these Agreements can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.
Product warranty can be found at www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at http://www.crestron.com/legal/patents.The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, AirMedia, and PinPoint are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. App Store, iTunes, and Mac, are either trademarks or registered trademarks of Apple Inc. in the United States and/or other
countries. IOS is either a trademark or registered trademark of Cisco Technology, Inc. in the United States and/or other countries. Android and Google Play are either trademarks or registered trademarks of Google Inc. in the United States and/or other countries. HDMI is either a trademark or
registered trademark of HDMI Licensing LLC in the United States and/or other countries. Windows is either a trademark or registered trademark of Microsoft Corporation in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn more about this product, use a QR reader application on
your mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
Pause the currently displayed image.
Save the currently displayed image.
View the currently displayed image at the actual size.
View the currently displayed image at the full-screen size.
Refresh the image.
Exit remote viewing and return to the download screen.