Crestron DM-TX-401-C User manual

DO GUIDE
DO Check the Box
QTY PRODUCT PART NUM.
1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2037209
1Interface Connector, Plug, 2-Pin 20 03574
1Interface Connector, Plug, 5-Pin 2003577
Not Included: Cables
NOTE: The DM OUT port is a PoDM (Power over DM) or PoH (Power over HDBaseT) PD
(Powered Device) port. To receive PoDM or PoH, the DM-TX-401-C requires a connection to
a DigitalMedia™ switcher or other equipment that has a PoDM or PoH PSE (Power Sourcing
Equipment) port. Any wiring that is connected to a PoDM or PoH PSE port is for intra-building
use only and should not be connected to a line that runs outside of the building in which the
PSE is located.
DO Set the IP Address
The conguration of the DM-TX-401-C within the DigitalMedia 8G+™ system determines how
the IP address of the DM-TX-401-C is set:
• If the DM-TX-401-C connects to a DigitalMedia switcher, the DM-TX-401-C is congured by
the switcher automatically.
• If the DM-TX-401-C connects to a DigitalMedia 8G+ receiver, the DM-TX-401-C uses its
own conguration settings. By default, DHCP (Dynamic Host Conguration Protocol) is
enabled. If desired, you can assign the default IP address to the DM-TX-401-C by holding
down the SETUP button while the unit boots up. The default IP address 192.168.1.234
overwrites the current setting. To manually set a different IP address, use Crestron
Toolbox™.
DO Select Inputs
By default, automatic switching of inputs is enabled. Automatic switching causes inputs to
switch according to the following priorities:
•Video switching priority: DisplayPort, HDMI, RGB, composite
•Audio switching priority: DisplayPort, HDMI, 1/8” analog, dual RCA analog
The AUTO LED on the front panel of the DM-TX-401-C lights to indicate that automatic switching
is enabled.
To manually select the desired audio/video input, press the SELECT button on the front panel of
the DM-TX-401-C until the corresponding LED lights (refer to illustration ).
DM-TX- 401-C
DigitalMedia 8G+™ Transmitter 401
DO Mount the DM-TX-401-C
Mount the Crestron®DM-TX-401-C in the desired location (for example, in a stationary rack or
podium, on a shelf, or in a movable lectern or AV cart). If rack mounting is desired, use the
ST-RMK Rack Mount Kit (sold separately).
DO Make Connections to the DM-TX-401-C
Make connections to the front and rear of the DM-TX-401-C as appropriate for the application
(refer to illustrations and ).
Unbalanced Stereo
Line Level
Audio Input
Unbalanced Stereo
Line Level
Audio Input
To Any
RS-232
Device
To IR Device (e.g.,
Projector) or Devices
Without RS-232
Ground
Composite
Video
Input
RGB or
Component
Video Input
HDMI®
Digital Video/
Audio Input
DisplayPort
Digital Video/
Audio Input
24 Vdc from
Power Pack
(Included) 10BASE-T/
100BASE-TX
Ethernet to Local
Network Device
To DM®Switcher,
Receiver, or Other
DM Device or to
HDBaseT®Device
VID PC
VIDEO IN
AUDIO IN
HDMI
DISPLAY PORT
L
G
COM
TX RX RS
CS
DM OUT
IR
24V
S G
G
0.75A LAN
R
Rear Panel Connections
Mouse/Keyboard Input
VIDEOAUTOSETUP
INPUT
DM
LINK
USB HID
PC HDMI
DISPLAY
PORT SELECT
RESET
PWR
DM-TX-401-C
Front Panel Connection
VIDEOAUTOSETUP
INPUT
DM
LINK
USB HID
PC HDMI
DISPLAY
PORT SELECT
RESET
PWR
DM-TX-401-C
Input Selection LEDs and Button

DO GUIDE DOC. 7748A (2043104) 01.15
Specications subject to change without notice.
Pressing the SELECT button in succession changes input selection from automatic switching
(default setting) to the various available selections in the following order:
• DisplayPort audio and video: The DISPLAY PORT LED lights.
• HDMI audio and video: The HDMI LED lights.
• VGA video with 1/8” audio: The PC LED lights.
• Composite video with dual RCA audio: The VIDEO LED lights.
• None: No input is selected.
After cycling through the above selections, pressing the SELECT button returns to automatic
switching.
DO Learn More
Visit the website for additional information and the latest rmware updates.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specic patents that cover Crestron products are listed at patents.crestron.com. Product warranty can be found at www.crestron.com/warranty.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, DigitalMedia 8G+, and DM are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/
or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and the
HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may
be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron
is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.