Crestron DigitalMedia XiO Director DM-XIO-DIR-160 Dimensional drawing

DO GUIDE
DM-XIO-DIR-80/DM-XIO-DIR-160
DigitalMedia™ XiO Director Virtual Switching Appliance
NOTE: The MGMT port is used for management and monitoring of the DM-XIO-DIR hardware.
The MGMT port does not provide access to the DM-XIO-DIR software and is independent of
Ethernet ports 1–4.
NOTE: Ethernet ports 1–4 provide access to the DM-XIO-DIR software and allow conguration of
the software. The ports are independent of each other and have different network settings.
Rear Panel Connections
DO Congure the Device
Using the web interface, congure the DM-XIO-DIR software. To access the web interface, open a
web browser and then go to the IP address of any one of the connected Ethernet ports labeled 1–4.
NOTE: By default, DHCP is enabled and each of the Ethernet ports labeled 1–4 is automatically
assigned a different IP address. If a DHCP server does not exist on the network, the IP address of
each of the four Ethernet ports defaults to a link-local address in the 169.254.xxx.xxx range (refer to
RFC 3927 for information about link-local addressing). The link-local address is different for each of
the four Ethernet ports. To nd the IP address of any of the connected Ethernet ports (1-4), use the
Device Discovery Tool in the Crestron Toolbox™ software.
NOTE: The Ethernet port that is being used to congure the DM-XIO-DIR software must be
accessible from the networks of the device running the web browser, the associated DM-NVX
devices, and the control system (if present).
To log in to the web interface, enter the user name and password. The default user name is admin,
and the default password is admin.
DO Install the Device
The Crestron®DM-XIO-DIR-80 and DM-XIO-DIR-160 can be mounted into a rack. Each device
occupies 1U of rack space.
WARNING: Do not lift the device using the front handles. The handles are designed to assist in
pulling the device from a rack.
Mount the device into a rack using four mounting screws (not included).
DO Connect the Device
Connect the device as required for the application.
Front Panel Connections
DO Check the Box
QTY PRODUCT PART NUM.
1Power Cord 2050 011
100-240V~
2-4A 50/60Hz:
From ac
power outlet
SERVICE:
For factory
use only
1–4:
10BASE-T/100BASE-TX/
1000BASE-T Ethernet to
video or control network
For factory
use only
For factory
use only
MGMT:
10BASE-T/100BASE-TX/
1000BASE-T Ethernet to
management network

DO GUIDE DOC. 8240A (2049889) 11.17
Specications subject to change without notice.
DO Learn More
Visit the website for additional information and the latest rmware
updates. To learn more about this product, use a QR reader
application on your mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Rack Mounting Safety Precautions
•Elevated Operating Ambient Temperature: If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be
given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specied by the
manufacturer.
•Reduced Airow: Installation of the equipment in a rack should be such that the amount of airow required for safe operation
of the equipment is not compromised.
•Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due
to uneven mechanical loading.
•Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the
effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
•Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given
to supply connections other than direct connections to the branch circuit (e.g., use of power strips).
Electrical Connection:
“This product must be connected to an earthed mains socket-outlet.”
• Finland: “Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.”
• Norway: “Apparatet må tilkoples jordet stikkontakt.”
• Sweden: “Apparaten skall anslutas till jordat uttag.”
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certain Crestron products contain open source software. For specic information, visit www.crestron.com/legal/open-source-software.
Crestron, the Crestron logo, Crestron Toolbox, and DigitalMedia are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other
trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.
DM-XIO-DIR-160
DM-XIO-DIR-80