Crestron HD-TX-301-C-E Dimensional drawing

DO GUIDE

HD-TX-301-C-E

DM Lite Multiformat Switch and Transmitter

DO Connect the Device

Connect the device as required for the application.

Front Panel Connection

Rear Panel Connections

NOTES:

• A power pack is included with the HD-TX-301-C-E. If a power pack is also included with

the compatible receiver, connect a power pack to either the transmitter or receiver. Do not

connect a power pack to both devices simultaneously. Power is transmitted over the cable

that connects the TO RX port on the transmitter to the FROM TX port on the receiver.

• Cabling that connects the TO RX port to the FROM TX port is designed for intrabuilding

use only.

DO Install the Device

Mount the device onto a at surface or rack rail.

Mount onto a Flat Surface

Using four mounting screws (not included), mount the device onto a at surface such as a wall.

Mount onto a Rack Rail

Mount the device onto the front or rear rail of a rack. Position either the left or right mounting ange

of the device so that the holes align with the holes in the rack. Then, secure the device to the rack

using two mounting screws (not included).

DO Check the Box

QTY ITEM PART NUM.

1 Power Pack, 24 Vdc 1.25 A, 100-240 Vac 2045870

HDMI 1-2:

From HDMI®

audio/video

sources

VGA 3:

From RGB (VGA)

or component

video source

TO RX:

To FROM TX

link input of

DM Lite receiver

AUDIO:

Unbalanced

stereo line level

audio input

24V

1.25A:

From included

power pack

SERVICE:

From TT-100

series cable caddy

DO GUIDE DOC. 8331B (2052058) 07.18

Specications subject to change without notice.

DO Congure the Device

To congure the device, do either of the following:

• If the transmitter connects to an HD-RX-201-C-E, congure the transmitter using the

web interface of the HD-RX-201-C-E. The HD-RX-201-C-E hosts the conguration of the

transmitter.

To access the web interface, open a web browser and then go to the IP address of the

HD-RX-201-C-E. By default, DHCP is enabled. To display the IP address on the connected

HDMI®display, press the SETUP button on the front panel of the HD-RX-201-C-E.

Pressing the SETUP button on the transmitter will also display the IP address of

the HD-RX-201-C-E.

To log in to the web interface, enter the user name and password. The default user name

and password are both admin.

• If the transmitter does not connect to an HD-RX-201-C-E, refer to Answer ID 1000168

in the Online Help section of the Crestron website (www.crestron.com/onlinehelp) for

conguration information.

NOTE: When the transmitter does not connect to the HD-RX-201-C-E, pressing the

SETUP button on the transmitter has no effect.

DO Learn More

Visit the website for additional information and the latest rmware updates. To learn

more about this product, use a QR reader application on your mobile device to scan

the QR image.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL®Standards and requirements tested by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.

The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.

Certain Crestron products contain open source software. For specic information, visit www.crestron.com/legal/open-source-software.

Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or other countries. HDMI and the HDMI logo are either

trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters

Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.