Crestron DM NVX Series User manual

DM NVX® Network AV
Encoders/Decoders
DM-NVX-363
DM-NVX-360
DM-NVX-363C
DM-NVX-360C
Product Manual
Crestron Electronics, Inc.

Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/legal/open-source-software.
Crestron, the Crestron logo, 3-Series, Crestron Toolbox, XiO Cloud, DigitalMedia, DM NAX, DM NVX, and DM NVX Director
are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
Audinate and Dante are either trademarks or registered trademarks of Audinate Pty Ltd. in the United States and/or other
countries. Dolby and Dolby Atmos are either trademarks or registered trademarks of Dolby Laboratories in the United
States and/or other countries. DTS HD and DTS:X are either trademarks or registered trademarks of DTS, Inc. in the United
States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing
LLC in the United States and/or other countries. Active Directory is either a trademark or registered trademark of Microsoft
Corporation in the United States and/or other countries. USB 2.0 Type-C is either a trademark or registered trademark of
USB Implementers Forum, Inc., in the United States and/or other countries. DisplayPort is either a trademark or registered
trademark of Video Electronics Standards Association in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not
responsible for errors in typography or photography.
©2021 Crestron Electronics, Inc.

Product Manual – DOC. 8879C Contents •i
Contents
Introduction.................................................................................................................................... 1
Physical Description......................................................................................................................2
DM-NVX-363 and DM-NVX-360 ............................................................................................................. 2
Front Panel ........................................................................................................................................... 2
Rear Panel.............................................................................................................................................4
DM-NVX-363C and DM-NVX-360C .......................................................................................................6
Status and Configuration........................................................................................................... 8
DMF-CI-8 Chassis Details........................................................................................................................9
Using the Web Interface....................................................................................................................9
Using SIMPL Windows .....................................................................................................................10
DM NVX Director Virtual Switching Appliance..................................................................................10
Encoding and Decoding Functionality ..................................................................................................11
Using the Web Interface...................................................................................................................11
Using SIMPL Windows ..................................................................................................................... 12
Device Mode Locking............................................................................................................................... 13
Crestron XiO Cloud Service Connection ............................................................................................. 14
Automatic Point-to-Point Connectivity .............................................................................................. 15
Using the Web Interface.................................................................................................................. 15
Using SIMPL Windows ..................................................................................................................... 16
Stream Statistics..................................................................................................................................... 16
Using the Web Interface.................................................................................................................. 16
Using SIMPL Windows ..................................................................................................................... 17
Image Preview .......................................................................................................................................... 17
Using the Web Interface.................................................................................................................. 18
Using SIMPL Windows ..................................................................................................................... 19
Multicast TTL (Time-to-Live)................................................................................................................. 19
Using the Web Interface................................................................................................................. 20
Using SIMPL Windows ..................................................................................................................... 21
DSCP (Differentiated Services Code Point) ...................................................................................... 21
Adaptive Bit Rate.....................................................................................................................................23
Using the Web Interface..................................................................................................................24
Using SIMPL Windows .....................................................................................................................24
DM NAX Audio over IP (AES67) ............................................................................................................25
Using the Web Interface..................................................................................................................25
Using SIMPL Windows .....................................................................................................................29
Dante and AES67 Audio Embedding and De-embedding .............................................................. 30
Using the Web Interface.................................................................................................................. 31
Using SIMPL Windows .....................................................................................................................32
7.1 Surround Sound Audio ......................................................................................................................33
Analog Audio Input or Output...............................................................................................................33
Using the Web Interface..................................................................................................................34
Using SIMPL Windows .....................................................................................................................35
Breakaway Audio .....................................................................................................................................35

ii •Contents Product Manual – DOC. 8879C
Using the Web Interface..................................................................................................................35
Using SIMPL Windows .....................................................................................................................36
Automatic Routing of Video Inputs......................................................................................................37
Using the Web Interface..................................................................................................................37
Using SIMPL Windows .....................................................................................................................37
Subscriptions ............................................................................................................................................38
Using the Web Interface..................................................................................................................38
Using SIMPL Windows .................................................................................................................... 40
Daisy Chain .............................................................................................................................................. 40
Switching Subscribed Transmitters ............................................................................................. 40
Switching Nonsubscribed Transmitters ....................................................................................... 41
EDID (Extended Display Identification Data)....................................................................................42
Automatic Display Control ....................................................................................................................44
Video Wall Processing .............................................................................................................................47
Using the Web Interface..................................................................................................................47
Using SIMPL Windows .....................................................................................................................49
Adjustable Underscan .............................................................................................................................49
Using the Web Interface..................................................................................................................49
Using SIMPL Windows .................................................................................................................... 50
User-Selectable Output Resolution ..................................................................................................... 51
Using the Web Interface.................................................................................................................. 51
Using SIMPL Windows .....................................................................................................................52
Maximum Color Depth and Color Space Mode .................................................................................53
Using the Web Interface..................................................................................................................53
Using SIMPL Windows .....................................................................................................................55
Background Image...................................................................................................................................55
Using the Web Interface..................................................................................................................55
Using SIMPL Windows .................................................................................................................... 60
Still Image Detection.............................................................................................................................. 60
USB 2.0 Routing ....................................................................................................................................... 61
Using the Web Interface..................................................................................................................62
Using SIMPL Windows .....................................................................................................................64
USB HID Hot Key Functionality ............................................................................................................66
Network Port Selection...........................................................................................................................66
Test Pattern Generator ......................................................................................................................... 68
Using the Web Interface................................................................................................................. 68
Using SIMPL Windows ..................................................................................................................... 71
Enterprise-Grade Security .....................................................................................................................72
Authentication Management .........................................................................................................72
IEEE 802.1X Authentication ............................................................................................................73
Automatic Firmware Update ................................................................................................................75
IGMP Snooping............................................................................................................................77
Troubleshooting..........................................................................................................................80
Appendix. Device Discovery ...................................................................................................... 83

Product Manual – DOC. 8879C DM-NVX-36x(C) Encoders/Decoders •1
Introduction
Crestron® DM NVX® network AV encoders/decoders transport ultra high-definition
4K video with 60 Hz frame rates and 4:4:4 color sampling over standard Gigabit
Ethernet. Using Pixel Perfect Processing technology, a video signal is encoded and then
decoded to achieve imperceptible end-to-end latency of less than 1 frame.
DM-NVX-36x(C) encoders/decoders consist of the following:
•Surface-mountable endpoints: DM-NVX-363 and DM-NVX-360. Compact in
design, the endpoints are designed to fit in various locations, for example, behind
a flat panel display.
•Card endpoints: DM-NVX-363C and DM-NVX-360C. The cards are designed to
occupy a card slot in the DMF-CI-8 card chassis.
The DM-NVX-363 and DM-NVX-363C provide the same functionality as the DM-NVX-
360 and DM-NVX-360C with the addition of Dante® audio networking and surround
sound to stereo downmixing. All DM-NVX-36x(C) devices offer encoding and decoding
capabilities in a single unit.
NOTE: DM-NVX-36x(C) encoders/decoders are compatible with DM-NVX-35x(C)
encoders/decoders, DM-NVX-E30(C) encoders, DM-NVX-D30(C) decoders, and
DM-NVX-D80-IOAV decoders. Scaling is supported by DM-NVX-36x(C) and
DM-NVX-35x(C) decoders only.
This manual provides information about the following:
•Physical description
•Configuration and status
•IGMP snooping
•Troubleshooting
In addition, information about device discovery of a DM NVX device using Crestron
Toolbox™ software is provided in the appendix of this manual.
For DM-NVX-36x(C) installation information, refer to the following documents as
applicable:
•DM-NVX-363 and DM-NVX-360 Quick Start (Doc. 8634)
•DM-NVX-363C and DM-NVX-360C Quick Start (Doc. 8636)
For information about designing a DM NVX system, refer to the DM NVX AV-over-IP
System Design Guide (Doc. 7977).

2 •DM-NVX-36x(C) Encoders/Decoders Product Manual – DOC. 8879C
Physical Description
The following sections provide information about the connectors, controls, and indicators
that are available on the DM-NVX-36x(C) devices.
DM-NVX-363 and DM-NVX-360
This section provides information about the front and rear panels of the DM-NVX-363
and DM-NVX-360.
Front Panel
The following illustration shows the front panel of the DM-NVX-363 and DM-NVX-360.
DM-NVX-363 and DM-NVX-360 Front Panel
OL and NV LEDs: Green OL LED indicates that the device is online with a control
system.
Green NV LED indicates that the device is encoding (transmitting) or decoding
(receiving) network video.
TX and RX LEDs: Green TX LED indicates that the device is in transmitter (encoder)
mode.
Green RX LED indicates that the device is in receiver (decoder) mode.
USB DEVICE: USB 2.0 Type-C™ connector, female;
USB 2.0 device port;
USB signal extender port for connection to a computer or other USB 2.0 host1
Ethernet 1: 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;
PoE+ PD (powered device) port,
IEEE 802.3at Type 2 PoE+ Class 4 (25.5 W) compliant2
Green LED indicates Ethernet link status;
Flashing amber LED indicates Ethernet activity
1The USB DEVICE and USB HOST ports cannot be used simultaneously.
2In order for Ethernet port 1 to receive PoE+, the port requires connection to a PoE+ compliant Ethernet switch
or other equipment that has a PoE+ PSE port. Ethernet port 1 is compatible with the Crestron DM-PSU-
ULTRA-MIDSPAN, PoE+ compliant Ethernet switch, or third-party IEEE 802.3at compliant PSE. Cabling that
connects to a PoE+ PSE port is designed for intrabuilding use only.
 
       

Product Manual – DOC. 8879C DM-NVX-36x(C) Encoders/Decoders •3
Ethernet 2: 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;
Green LED indicates Ethernet link status;
Flashing amber LED indicates Ethernet activity
Ethernet 3: 8-pin RJ-45 connector, female;
100BASE-TX Ethernet port;
Green LED indicates Ethernet link status;
Flashing green LED indicates Ethernet activity;
Amber LED indicates 100BASE-TX link status
Ethernet 4: SFP port;
Accepts one Crestron SFP-1G Series SFP transceiver module (sold separately);
Green LINK LED indicates Ethernet link status;
Flashing green ACT LED indicates Ethernet activity
USB HOST: USB Type-A connector, female;
USB 2.0 host port;
USB signal extender port for connection to a mouse, keyboard, or other
USB 2.0 device;1
Available Power: 500 mA at 5 VDC2
USB HID: USB Type-A connector, female;
USB 2.0 host port;
USB signal extender port for connection to a mouse, keyboard, or other
USB 2.0 device;
Available Power: 500 mA at 5 VDC2
HDMI OUTPUT: HDMI® Type A connector, female;
HDMI digital video/audio output (DVI compatible);3
Green LED indicates video signal transmission at the HDMI output
HDMI INPUT: 19-pin HDMI Type A connector, female;
HDMI digital video/audio inputs (DVI and Dual-Mode DisplayPort™ compatible);3
Green LED indicates sync detection at the HDMI input
AUDIO I/O: 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio input or output;
Input Impedance: 24k Ohms balanced/unbalanced;
Maximum Input Level: 4 Vrms balanced, 2 Vrms unbalanced;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
1The USB DEVICE and USB HOST ports cannot be used simultaneously.
2When PoE+ is used to power the DM NVX device, a maximum of 500 ma is available to power both the USB
HOST and USB HID ports. To prevent possible instability issues, it is recommended that the PW-2412WU
power pack (sold separately) be used.
3HDMI connections require an appropriate adapter or interface cable to accommodate a DVI or Dual-Mode
DisplayPort signal. CBL-HD-DVI interface cables are sold separately.

4 •DM-NVX-36x(C) Encoders/Decoders Product Manual – DOC. 8879C
Rear Panel
The following illustration shows the rear panel of the DM-NVX-363 and DM-NVX-360.
DM-NVX-363 and DM-NVX-360 Rear Panel
PWR: Bicolor green/amber LED, indicates operating power is being supplied, lights
amber while booting and green when operating
SETUP: Recessed push button for on-screen IP address display and to change the
operating mode (transmitter or receiver). Red LED indicates that the SETUP button
is pressed and times out automatically.
NOTES:
•When a DM-NVX-36x(C) decoder is connected to a DM-NVX-36x(C), DM-NVX-
35x(C), or DM-NVX-E30(C) encoder, pressing the SETUP button on the decoder
for less than 10 seconds displays the encoder and decoder IP addresses on the
display connected to the HDMI output of the decoder.
•When a DM-NVX-36x(C) encoder is connected to a DM-NVX-36x(C), DM-NVX-
D30(C) or DM-NVX-D80-IOAV decoder, pressing the SETUP button on the
encoder for less than 10 seconds displays the encoder IP address on the display
connected to the HDMI output of the encoder. In addition, the encoder and
decoder IP addresses are shown on the display connected to the HDMI output of
the decoder.
•When a DM-NVX-36x(C) encoder is connected to a DM-NVX-35x(C) decoder,
pressing the SETUP button on the encoder for less than 10 seconds displays the
encoder IP address on the display connected to the HDMI output of the encoder.
In addition, the decoder IP address is shown on the display connected to the
HDMI output of the decoder.
•When the SETUP button is pressed for 10 seconds, a message appears on the
display stating that the button must be pressed again to change the operating
mode. Pressing the button a second time changes the operating mode from a
receiver (decoder) to a transmitter (encoder) or from a transmitter to a receiver
and reboots the device.
The SETUP button can be used to change the operating mode only when Device
Mode Lock is disabled in the System Setup section under the Settings tab.
For additional information, refer to “Device Mode Locking” on page 13.
RESET: Recessed push button for hardware reset
INPUT SEL: Push button for manual input selection (HDMI or NV [network video])
        


Product Manual – DOC. 8879C DM-NVX-36x(C) Encoders/Decoders •5
INPUT SEL, HDMI LED: Green indicates that the HDMI input is selected. Amber
indicates that an HDMI signal is detected but the HDMI input is not selected.
INPUT SEL, NV LED: Green indicates that the NV (network video) input is selected.
Amber indicates that network video is detected but the NV input is not selected.
IR 1–2: 4-pin 3.5 mm detachable terminal block;
Comprises two IR/serial ports;
IR output up to 1.1 MHz;
1-way serial TTL (0–5 V) up to 19200 baud;
Crestron IRP2 emitter sold separately
COM: 5-pin 3.5 mm detachable terminal block;
Bidirectional RS-232 port;
Up to 115.2k baud, hardware and software handshaking support
24VDC 1.25A: 2.1 x 5.5 mm DC power connector;
24 VDC power input;
PW-2412WU power pack sold separately
Ground: 6-32 screw, chassis ground lug

6•DM-NVX-36x(C) Encoders/Decoders Product Manual – DOC. 8879C
DM-NVX-363C and DM-NVX-360C
The following illustration shows the connectors, controls, and indicators that are
available on the DM-NVX-363C and DM-NVX-360C.
NOTE: The DM-NVX-363C and DM-NVX-360C contain the same connectors, controls,
and indicators. For illustrative purposes, only the card named DM-NVX-363Cis
shown below.
DM-NVX-363C
OL and NV LEDs: Green OL LED indicates that the device is online with a control
system.
Green NV LED indicates that the device is encoding (transmitting) or decoding
(receiving) network video.
TX and RX LEDs: Green TX LED indicates that the device is in transmitter (encoder)
mode.
Green RX LED indicates that the device is in receiver (decoder) mode.
USB DEVICE: USB 2.0 Type-C™ connector, female;
USB 2.0 device port;
USB signal extender port for connection to a computer or other USB 2.0 host1
Ethernet 1: 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;
Green LED indicates Ethernet link status;
Flashing amber LED indicates Ethernet activity
Ethernet 2: 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;
Green LED indicates Ethernet link status;
Flashing amber LED indicates Ethernet activity
Ethernet 3: 8-pin RJ-45 connector, female;
100BASE-TX Ethernet port;
Green LED indicates Ethernet link status;
Flashing green LED indicates Ethernet activity;
Amber LED indicates 100BASE-TX link status
1The USB DEVICE and USB HOST ports cannot be used simultaneously.

Product Manual – DOC. 8879C DM-NVX-36x(C) Encoders/Decoders •7
Ethernet 4: SFP port;
Accepts one Crestron SFP-1G Series SFP transceiver module (sold separately);
Green LINK LED indicates Ethernet link status;
Flashing green ACT LED indicates Ethernet activity
USB HOST: USB Type-A connector, female;
USB 2.0 host port;
USB signal extender port for connection to a mouse, keyboard, or other
USB 2.0 device;1
Available Power: 500 mA at 5 VDC
USB HID: USB Type-A connector, female;
USB 2.0 host port;
USB signal extender port for connection to a mouse, keyboard, or other
USB 2.0 device;
Available Power: 500 mA at 5 VDC
HDMI OUTPUT: HDMI Type A connector, female;
HDMI digital video/audio output (DVI compatible);2
Green LED indicates video signal transmission at the HDMI output
HDMI INPUT: 19-pin HDMI Type A connector, female;
HDMI digital video/audio inputs (DVI and Dual-Mode DisplayPort™ compatible);2
Green LED indicates sync detection at the HDMI input
AUDIO I/O: 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio input or output;
Input Impedance: 24k Ohms balanced/unbalanced;
Maximum Input Level: 4 Vrms balanced, 2 Vrms unbalanced;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
1The USB DEVICE and USB HOST ports cannot be used simultaneously.
2HDMI connections require an appropriate adapter or interface cable to accommodate a DVI or Dual-Mode
DisplayPort signal. CBL-HD-DVI interface cables are sold separately.

8 •DM-NVX-36x(C) Encoders/Decoders Product Manual – DOC. 8879C
Status and Configuration
This section provides information about viewing or configuring the following items using
the web interface or SIMPL Windows as applicable:
•DMF-CI-8 chassis details
•DM NVX Director™ virtual switching appliance
•Encoding and decoding functionality
•Device mode locking
•Crestron XiO Cloud® service connection
•Automatic point-to-point connectivity
•Stream statistics
•Image preview
•Multicast TTL (Time-to-Live)
•Differentiated Services Code Point (DSCP)
•Adaptive bit rate
•DM NAX™ audio over IP (AES67)
•Dante and AES67 audio embedding and de-embedding
•7.1 surround sound audio
•Analog audio input or output
•Breakaway audio
•Automatic routing of video inputs
•Subscriptions
•Daisy chain
•EDID (Extended Display Identification Data)
•Automatic display control
•Video wall processing
•Adjustable underscan
•User-selectable output resolution
•Maximum color depth and color space mode
•Background image
•Still image detection
•USB 2.0 routing

Product Manual – DOC. 8879C DM-NVX-36x(C) Encoders/Decoders •9
•USB hot key functionality
•Network port selection
•Test pattern generator
•Enterprise-grade security
•Automatic firmware update
DMF-CI-8 Chassis Details
NOTE: DMF-CI-8 chassis details apply to the DM NVX cards only and do not apply to
DM NVX surface-mountable endpoints.
A DM NVX card occupies a card slot in a DMF-CI-8 chassis. Information about the
chassis can be viewed using the web interface or SIMPL Windows.
Using the Web Interface
To view DMF-CI-8 chassis information, click the Status tab and then click Chassis.
The Chassis section displays the following information:
•Serial number of the chassis
•Number of the slot into which the card is installed
Status Tab – Chassis

10 •DM-NVX-36x(C) Encoders/Decoders Product Manual – DOC. 8879C
Using SIMPL Windows
Using the top-level programming slot for the DM NVX card, program the
<ChassisSerialNumber_F>serial output join to report the serial number of the chassis in
which the card is installed. Program the <CardSlotInfo_F> serial output join to report the
slot number in which the card is installed in the chassis.
DM NVX Director Virtual Switching Appliance
If a DM NVX device is managed by a DM NVX Director™ virtual switching appliance,
information about the appliance can be viewed using the web interface.
To view DM NVX Director appliance information, click the Status tab and then click
DM NVX Director.
The DM NVX Director section displays the following information:
•DM NVX Director host name
•Domain name, number, and slot number to which the DM NVX device is assigned
Status Tab – DM NVX Director

Product Manual – DOC. 8879C DM-NVX-36x(C) Encoders/Decoders •11
Encoding and Decoding Functionality
A DM-NVX-36x(C) device can be configured to function as a network AV encoder
(transmitter) or decoder (receiver):
•As an encoder, a DM NVX device allows a laptop computer, camera, or other
media source to be connected via an HDMI cable and then transmitted over the
network.
•As a decoder, a DM NVX device receives the signal from a DM NVX encoder and
feeds the signal to a display device via the HDMI output. A DM NVX decoder can
switch streams among multiple DM NVX encoders on the network alongside
locally connected HDMI sources.
To set the operating mode of a DM-NVX-36x(C) device as a transmitter or receiver, use
the web interface or SIMPL Windows as discussed in the following sections.
NOTES:
•When DM-NVX-36x(C) devices are used with DM-NVX-E30(C), DM-NVX-E760(C),
and DM-NVX-35x(C) encoders, the DM-NVX-36x(C) devices must be in Receiver
mode. When DM-NVX-36x(C) devices are used with DM-NVX-D30(C), DM-NVX-
D80-IOAV, and DM-NVX-35x(C) decoders, the DM-NVX-36x(C) devices must be in
Transmitter mode.
•For a DM-NVX-36x surface-mountable endpoint, the SETUP button can be used to
change the operating mode from a receiver to a transmitter or from a transmitter to
a receiver. For additional information, refer to the description of the SETUP button
on page 4.
For a DM-NVX-36xC card, the front panel of the DMF-CI-8 chassis can be used to
change the operating mode. For additional information, refer to the DMF-CI-8
Supplemental Guide (Doc. 7861).
Using the Web Interface
To set the DM-NVX-36x(C) operating mode:
1. Click the Settings tab and then click Stream.
2. In the Mode drop-down list, select Receiver or Transmitter. The default setting is
Receiver (decoder).

12 •DM-NVX-36x(C) Encoders/Decoders Product Manual – DOC. 8879C
Settings Tab – Stream, Mode Configuration
When a different mode is selected, a prompt appears asking for confirmation that the
device be rebooted. Click the Yes, Reboot Now button to reboot the device.
Device Reboot Prompt
For additional information, refer to the online help of the web interface.
Using SIMPL Windows
Using the top-level programming slot for the DM-NVX-36x(C) device, set the
<DeviceMode>analog input join to the desired mode (Receiver or Transmitter).
The default setting is Receiver.
Changing modes requires that the device be rebooted. Trigger the <Reboot> digital
input join to reboot the device. For additional information, refer to the SIMPL Windows
help file.

Product Manual – DOC. 8879C DM-NVX-36x(C) Encoders/Decoders •13
Device Mode Locking
Device mode locking controls whether the SETUP button on a DM-NVX-36x and the
DMF-CI-8 front panel can be used to change the operating mode of the DM-NVX-36x
and DM-NVX-36xC devices, respectively. The operating mode determines when the
DM-NVX-36x(C) device functions as a receiver or transmitter.
NOTE: Device mode locking does not apply to the Mode setting in the Stream section
under the Settings tab.
To configure device mode locking:
1. Click the Settings tab and then click System Setup.
2. In the Device Mode Lock section, do either of the following:
•Allow the operating mode to be changed by setting the Control Lock toggle
switch in the Off (left) position (default setting).
•Prevent the operating mode from being changed by setting the Control Lock
toggle switch in the On (right) position.
Settings Tab – System Setup, Device Mode Lock Configuration
For additional information, refer to the online help of the web interface.

14 •DM-NVX-36x(C) Encoders/Decoders Product Manual – DOC. 8879C
Crestron XiO Cloud Service Connection
The Crestron XiO Cloud® service enables supported Crestron devices across an
enterprise to be managed and configured from one central and secure location in the
cloud. Connection to the Crestron XiO Cloud service can be enabled or disabled using the
web interface.
To configure the connection to the Crestron XiO Cloud service:
1. Click the Settings tab and then click System Setup.
2. In the Cloud Settings section, set the Cloud Configuration Service Connection
toggle switch in the On (right) or Off (left) position. The default setting is in the
On position.
Settings Tab – System Setup, Cloud Settings
For instructions about how to connect to the service, refer to the DM-NVX-363 and DM-
NVX-360 Quick Start (Doc. 8634) or DM-NVX-363C and DM-NVX-360C Quick Start
(Doc. 8636) as appropriate. For information about using the service, refer to the
XiO Cloud Provisioning and Management Service User Guide (Doc. 8214).

Product Manual – DOC. 8879C DM-NVX-36x(C) Encoders/Decoders •15
Automatic Point-to-Point Connectivity
Point-to-point connectivity enables a DM NVX encoder to be connected directly to a
DM NVX decoder to stream video, audio, and USB. Rather than being connected to an
Ethernet switch, a 1000BASE-T Ethernet port of an encoder is connected directly to a
1000BASE-T port of a decoder. By default, point-to-point mode is enabled (set to Auto)
and can be disabled if desired.
When point-to-point mode is enabled, no additional configuration is required for the
encoder or decoder to operate in point-to-point mode; however, the operating mode of a
DM-NVX-36x(C) device must be set correctly. If the device is to function as an encoder,
the operating mode must be set to Transmitter. If the device is to function as a decoder,
the operating mode must be set to Receiver. For information about setting the
operating mode of DM-NVX-36x(C) devices, refer to Encoding and Decoding
Functionality.
To enable or disable point-to-point mode, use the web interface or SIMPL Windows as
discussed in the following sections.
Using the Web Interface
Enable or disable point-to-point mode by clicking the Settings tab and then clicking
System Setup.
In the Point-to-Point Control section, Point to Point Status indicates whether point-to-
point mode is Active or Inactive.
In the Point-to-Point Mode drop-down list, select either of the following:
•Auto: (Default setting) A 1000BASE-T port of a DM NVX encoder detects a
direct connection to a DM NVX decoder or a connection to a 1000BASE-T switch.
Similarly, a 1000BASE-T port of a DM NVX decoder detects a direct connection
to a DM NVX encoder or a connection to a 1000BASE-T switch. If a direct
connection between an encoder and decoder is detected, point-to-point mode is
automatically enabled.
•Disable: Disables point-to-point mode

16 •DM-NVX-36x(C) Encoders/Decoders Product Manual – DOC. 8879C
Settings Tab - System Setup, Point-to-Point Control
Using SIMPL Windows
Using the top-level programming slot for the DM-NVX-36x(C) device, set the
<PointToPointMode> analog input join to the desired value. For additional information,
refer to the SIMPL Windows help file.
Stream Statistics
Statistics can be displayed to indicate the number of packets received or transmitted,
the number of dropped packets, and the bit rate of the received stream. To enable or
disable or to reset stream statistics, use the web interface or SIMPL Windows as
discussed in the following sections.
Using the Web Interface
To enable, disable, or reset stream statistics:
1. Click the Settings tab and then click Stream.
2. In the Advanced section:
•To enable or disable Statistics,set the Statistics toggle switch in the On
(right) or Off (left) position, respectively. The default setting is in the Off
(left) position.
•To reset statistics, click Reset Statistics.
For additional information, refer to the online help of the web interface.