Crestron HD-RX-4K-510-C-E User manual

The Crestron® HD-RX-4K-510-C-E and HD-RX-4K-410-C-E are 4K
multiformat AV switches and receivers. The devices provide enhanced
HDMI® video switching and audio presentation capabilities in areas such
as conference rooms and classrooms.
In the Box
1 HD-RX-4K-510-C-E or HD-RX-4K-410-C-E Multiformat AV
Switch and Receiver
Additional Items
4 Anchor, Drywall, Plastic (2053825)
5 Connector, 2-Pin (2003574)
2 Connector, 2-Pin (2044402)
3 Connector, 3-Pin (2003575)
5 Connector, 5-Pin (2003577)
1 Power Cord, 6 ft 7 in. (2 m) (2001134)
4 Screw, 8-15A x 3/4 in., Flat Head, Phillips (2053836)
Install the Device
To install the device, mount it onto drywall. Use the four included drywall
anchors and the four included 8-15A x 3/4 in. flat head Phillips screws
(one screw for each keyhole slot in the four mounting flanges of the
device).
NOTE: For safety reasons, it is recommended that the mounting
height of the device be no more than 6-1/2 ft (2 m) from the floor or
any platform above which the device is mounted.
Drywall Mounting (HD-RX-4K-510-C-E Shown)
HD-RX-4K-510-C-E and HD-RX-4K-410-C-E Quick Start
1

Connect the Device
Connect the device as required for the application.
Front Panel Connection (HD-RX-4K-510-C-E Shown)
HD-RX-4K-510-C-E and HD-RX-4K-410-C-E Quick Start
2

Rear Panel Connections (HD-RX-4K-510-C-E Shown)
HD-RX-4K-510-C-E and HD-RX-4K-410-C-E Quick Start
3

NOTES:
lCabling that connects the device to a DM Lite™ transmitter is
designed for intrabuilding use only.
lThe HD-RX-4K-510-C-E can power three DM Lite transmitters
simultaneously. The HD-RX-4K-410-C-E can power two DM Lite
transmitters simultaneously. Do not connect power to DM Lite
transmitters that are to be connected to the HD-RX-4K-510-
C-E or HD-RX-4K-410-C-E.
lThe device is grounded by connection of the included power cord
to an AC power outlet with proper grounding.
lThere are no user-serviceable parts inside this device. If repair of
the device is needed, contact an authorized Crestron dealer for
return of the device to the factory.
LINE 1-2 Connector Pin Assignments
The LINE 1 and LINE 2 connectors use 5-pin terminal blocks for balanced
or unbalanced analog audio inputs.
LINE Connector
Refer to the following table and diagrams for LINE analog audio input pin
assignments and wiring information.
LINE Balanced and Unbalanced Audio Input Pin Assignments
Signal Name Balanced Audio Input Unbalanced Audio Input
+ L+ L+ In
− L− L− Signal return, jumper to GND
G Shield/ground Ground
+ R+ R+ In
− R− R− Signal return, jumper to GND
LINE Balanced and Unbalanced Audio Input Wiring
HD-RX-4K-510-C-E and HD-RX-4K-410-C-E Quick Start
4

AUX OUT 1-2 Connector Pin Assignments
The AUX OUT 1 and AUX OUT 2 connectors use 5-pin terminal blocks for
balanced or unbalanced analog audio outputs.
AUX OUT 1-2 Connector
Refer to the following table and diagrams for AUXOUT analog audio
output pin assignments and wiring information.
AUX OUT Balanced and Unbalanced Audio Output Pin Assignments
Signal Name Balanced Audio Output Unbalanced Audio Output
+ L+ L+ Out
− L− Open
G Shield/ground Common ground
+ R+ R+ Out
− R− Open
AUX OUT Balanced and Unbalanced Audio Output Wiring
LED Indicators
Refer to the following table for information about the LED indicators on
the device.
LED Indicators
LED
Indicator Color Meaning
PWR Amber Power is being applied to the device. The device is
booting.
Green Power is being applied to the device. The device is
operational.
INPUT 1-5
or 1-4
(model
dependent)
Green The corresponding input is routed to the HDMI®
output.
Amber The corresponding input is detected but is not
routed to the HDMI output.
AUTO Green Automatic routing is enabled.
SETUP Red The SETUP button is pressed.
DM LITE Green A DM Lite™ link is established.
Flashing
amber
Non-HDCP video is detected.
Steady
amber
HDCP video is detected.
LAN Green An Ethernet link is established.
Flashing
amber
Data activity is occurring on the Ethernet link.
HD-RX-4K-510-C-E and HD-RX-4K-410-C-E Quick Start
5

Configure the Device
Using the web interface, configure the HD-RX-4K-510-C-E or
HD-RX-4K-410-C-E. The device also hosts the configuration of the
connected DM Lite transmitters.
To access the web interface, open a web browser and then go to the IP
address of the HD-RX-4K-510-C-E or HD-RX-4K-410-C-E. By default,
DHCP is enabled. To display the IP address on the connected HDMI
display, press the SETUP button on the front panel of the device. If a
transmitter has a SETUP button, pressing the button on the transmitter
will also display the IP address of the HD-RX-4K-510-C-E or HD-RX-4K-
410-C-E.
To log in to the web interface, enter the user name and password.
The default user name and password are both admin .
Upgrade the Firmware
Before using the device, upgrade the firmware. The latest firmware can be
downloaded from the HD-RX-4K-510-C-E and HD-RX-4K-410-C-E
product pages on the Crestron website (www.crestron.com).
Connect to the Cloud
The Crestron XiO Cloud™ service allows supported Crestron devices
across an enterprise to be managed and configured from one central and
secure location in the cloud. Supported devices are preconfigured to
connect to the service. Use of the service requires a registered Crestron
XiO Cloud account.
To connect the device to the Crestron XiO Cloud service:
1. Record the MAC address and serial number that are labeled on the
shipping box or rear panel of the device. The MAC address and serial
number are required in order to add the device to the Crestron XiO
Cloud environment.
2. Do either of the following:
lIf you have a Crestron XiO Cloud account, go to
https://portal.crestron.io to access the Crestron XiO Cloud service.
lIf you do not have a Crestron XiO Cloud account, go to
www.crestron.com/xio-cloud-registration to register for an
account.
For detailed information about using the Crestron XiO Cloud service,
refer to the Crestron XiO Cloud Service User Guide (Doc. 8214) at
www.crestron.com/manuals.
HD-RX-4K-510-C-E and HD-RX-4K-410-C-E Quick Start
6

Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron XiO Cloud, and DM Lite are either trademarks or
registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. HDMI and the HDMI logo are either trademarks or registered trademarks of
HDMI Licensing LLC in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to
either the entities claiming the marks and names or their products. Crestron disclaims
any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
©2019 Crestron Electronics, Inc.
Doc ID 8496A
2054222
11/12/19
HD-RX-4K-510-C-E and HD-RX-4K-410-C-E Quick Start
7