Crestron DM-TX-4KZ-100-C-1G User manual

The Crestron® DM-TX-4KZ-100-C-1G is a DigitalMedia 8G+® wall plate
transmitter that supports 4K60 4:4:4 and HDR (High Dynamic Range)
video. The transmitter provides a cost-effective solution for a single AV
source as part of a complete Crestron DigitalMedia™ system.
In the Box
1 DM-TX-4KZ-100-C-1G DigitalMedia 8G+® Wall Plate
Transmitter
Additional Items
1 Bracket, Surface Mount (2016054)
1 Power Pack, 24 VDC 0.75 A, 100-240 VAC (2045866)
1 Connector, 2-Pin (2003574)
1 Connector, 3-Pin (2003575)
2 Screw, 6-32 x 3/4 in., Truss Head, Combo (2009211)
2 Screw, 6-32 x 1/4 in., Pan Head, SEMS (2007218)
DM-TX-4KZ-100-C-1G-B-T Only
1 Faceplate Assembly, 1 Gang, Textured Black (4523149)
1Front Faceplate, Plastic (2043449)
1Rear Faceplate, Plastic (2043453)
2Screw, 6-32 x 1/4 in., Flat Head, Phillips (2007211)
DM-TX-4KZ-100-C-1G-W-T Only
1 Faceplate Assembly, 1 Gang, Textured White (4522347)
1Front Faceplate, Plastic (2043379)
1Rear Faceplate, Plastic (2043380)
2Screw, 6-32 x 1/4 in., Flat Head, Phillips (2007211)
Install the Transmitter
Mount the transmitter into an electrical box, onto a flat surface, or onto a
rack rail. Connect the rear of the transmitter before mounting it into an
electrical box. If the transmitter is to be mounted onto a flat surface or
rack rail, connect the rear of the unit after it is mounted.
Connecting the Rear of the Transmitter
The DM OUT port on the rear of the transmitter is a PoDM (Power over
DM) and HDBaseT® PoE powered device (PD) port. To receive PoDM, the
port requires connection to a DigitalMedia switcher or other DigitalMedia
equipment that has a PoDM power sourcing equipment (PSE) port. To
receive HDBaseT PoE, the port requires connection to equipment that has
an HDBaseT PoE PSE port. Wiring that connects to a PoDM or HDBaseT
PoE port is for intrabuilding use only.
Connection of the transmitter to the included power pack is not required
when PoDM or HDBaseT PoE is used to power the transmitter.
Connections to Rear of Transmitter
DM-TX-4KZ-100-C-1G Quick Start
1

Mounting into an Electrical Box
The transmitter mounts into a 1-gang electrical box (not included).
1. Using a Phillips screwdriver and the two included 6-32 x 3/4-inch truss
combo head screws, attach the transmitter to the electrical box.
2. Using the included faceplate assembly:
a. Position the rear faceplate onto the front of the transmitter.
b. Using the two included 6-32 x 1/4-inch Phillips flat head screws,
attach the rear faceplate to the transmitter.
c. Position the front faceplate over the rear faceplate and press the
front faceplate until it snaps into place.
Mounting into an Electrical Box
Mounting onto a Flat Surface
Mount the transmitter onto a suitable flat surface such as the underside
of a table.
1. Using a Phillips screwdriver and the two included 6-32 x 1/4-inch
SEMS screws, attach the included surface-mount bracket to the
transmitter.
2. Attach the bracket to the flat surface using the two surface-mount
screw slots and two mounting screws (not included).
Mounting onto a Flat Surface
DM-TX-4KZ-100-C-1G Quick Start
2

Mounting onto a Rack Rail
Mount the transmitter onto the front or rear rail of a rack.
1. Position the transmitter horizontally so that the holes in the left or
right mounting flange align with the holes in the rack rail.
2. Secure the unit to the rack rail using two mounting screws
(notincluded).
Mounting onto a Rack Rail
Connecting the Front of the Transmitter
Connect the front of the transmitter as required for the application.
NOTES:
lThe IR OUT and COM ports are enabled only when the
transmitter connects to an Ethernet-enabled DigitalMedia
switcher or receiver that is addressable from a Crestron
control system.
lPass-through mode for RS-232 and CEC is supported.
For additional information, refer to Online Help Answer ID
1000497 on the Crestron website (www.crestron.com).
Connections to Front of Transmitter
DM-TX-4KZ-100-C-1G Quick Start
3

Observe the LED Indicators
LED indicators are provided on the front of the transmitter. The DM OUT
port, which is located on the rear and can be viewed from the top of the
transmitter, also includes LED indicators.
LED Indicators (Front and Top Views Shown)
Refer to the following table for information about the LED indicators.
LED
Indicator Color Meaning
POWER Green Indicates that operating power is being supplied via
PoDM, HDBaseT PoE, or the included power pack
VIDEO Green Indicates that a video signal is detected at the HDMI
input
DM
OUT
(Rear)
Green Indicates that a DM link is established
Solid
amber
Indicates HDCP video
Blinking
amber
Indicates non-HDCP video
Visit the Product Page
Scan the QR code to visit the product page.
DM-TX-4KZ-100-C-1G-B-T
www.crestron.com/model/6510626
DM-TX-4KZ-100-C-1G-W-T
www.crestron.com/model/6510627
DM-TX-4KZ-100-C-1G Quick Start
4

Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G+, and DM 8G+ are either
trademarks or registered trademarks of Crestron Electronics, Inc. in the United States
and/or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks
or registered trademarks of the HDBaseT Alliance in the United States and/or other
countries. HDMI and the HDMI logo are either trademarks or registered trademarks of
HDMI Licensing LLC in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to
either the entities claiming the marks and names or their products. Crestron disclaims
any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc. 8543A
(2054568)
01/08/20
DM-TX-4KZ-100-C-1G Quick Start
5