Crestron DM-TX-200-C-2G User manual

The Crestron® DM-TX-200-C-2G is a DigitalMedia 8G+® transmitter that
provides a remote wall plate or floor box input connection for HDMI® and
VGA sources as part of a complete DigitalMedia™ System. It includes a
USB HID device port, allowing a mouse/keyboard to be connected for
controlling a computer or other host device at a different location. The
DM-TX-200-C-2G mounts in a double-gang electrical box.
In the Box
1 DM-TX-200-C-2G,
Wall Plate DigitalMedia 8G+ Transmitter 200
Additional Items
4 Screw, #6-32 x 3/4 in., Truss Head, Combo (2009211)
Connect the Rear Panel
Connect the rear panel of the transmitter before installing the unit into
an electrical box (not included) or floor box (not included).
NOTE: The DM OUT port is a Power over DM (PoDM) and HDBaseT®
PoE (Power over Ethernet) powered device (PD) port. To receive PoDM
or HDBaseT PoE, the DM-TX-200-C-2G requires a connection to a
DigitalMedia switcher or other equipment that has a PoDM or
HDBaseT PoE power sourcing equipment (PSE) port. Any wiring
connected to a PoDM or HDBaseT PoE PSE port is for intrabuilding
use only and should not be connected to a line that runs outside of the
building in which the PSE is located.
1
DM-TX-200-C-2G QuickStart
Wall Plate DigitalMedia 8G+® Transmitter 200

Install the Transmitter
Install the DM-TX-200-C-2G into a 2-gang electrical box or into a 6 in.
floor box.
Install into an Electrical Box
Install the DM-TX-200-C-2G into a 2-gang electrical box in a wall, floor, or
ceiling. A minimum mounting depth of 2-1/2 in. (64 mm) is required.
To install the DM-TX-200-C-2G into an electrical box:
1. Use a Phillips screwdriver and the four included #6-32 x 3/4 in. screws
to attach the DM-TX-200-C-2G to the electrical box.
2. Attach a decorator-style faceplate (not included) to the front of the
DM-TX-200-C-2G using four screws (not included).
Install into a Floor Box
Install the DM-TX-200-C-2G into a 2-gang opening in a 6 in. (153 mm)
deep floor box.
Use a Phillips screwdriver and the four included #6-32 x 3/4 in. screws to
attach the DM-TX-200-C-2G to an installed floor box.
2
DM-TX-200-C-2G QuickStart
Wall Plate DigitalMedia 8G+® Transmitter 200

Connect the Front Panel
Connect the rear panel of the transmitter as required for the application.
Determine the IP Address
The configuration of the DM-TX-200-C-2G within a DM 8G+® system
determines how the IP address of the DM-TX-200-C-2G is set:
lIf the DM-TX-200-C-2G is connected to a DM switcher, the IP address
is configured by the switcher automatically.
lIf the DM-TX-200-C-2G is connected directly to a DM 8G+ receiver
(commonly referred to as a standalone configuration in which no
DigitalMedia switcher is used), the IP address of the transmitter is
assigned using DHCP (Dynamic Host Configuration Protocol) by
default. If you wish to assign a static IP address, do either of the
following:
oTo assign the default static IPaddress of the transmitter, hold
down the SETUP button while the unit boots up. The default static
IPaddress 192.168.1.239 overwrites the current setting.
oTo manually set a static IP address other than the default address,
use the Crestron Toolbox™ application.
3
DM-TX-200-C-2G QuickStart
Wall Plate DigitalMedia 8G+® Transmitter 200

Visit the Product Page
Scan the QR code to visit the product page.
DM-TX-200-C-2G
www.crestron.com/model/6505824
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, DigitalMedia 8G+, DM,
and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics,
Inc. in the United States and/or other countries. HDBaseT and the HDBaseT Alliance
logo are either trademarks or registered trademarks of the HDBaseT Alliance in the
United States and/or other countries. HDMI, the HDMI logo, and High Definition
Multimedia Interface are either trademarks or registered trademarks of HDMI
Licensing LLC in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to
either the entities claiming the marks and names or their products. Crestron disclaims
any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc. 7759C
05/07/20
4
DM-TX-200-C-2G QuickStart
Wall Plate DigitalMedia 8G+® Transmitter 200