Crestron DigitalMedia DMF-TX-4K-SFP Dimensional drawing

DO GUIDE
DO Connect the Device
Connect the rear panel of the device as required for the application.
Top View
Bottom View
DMF-TX- 4K-SFP
DigitalMedia™ SFP+ 4K Fiber Transmitter
DO Install the Device
The Crestron®DMF-TX-4K-SFP can be mounted onto a at surface or onto a rack rail.
Mounting onto a Flat Surface
Using four mounting screws (not included), mount the device onto a at surface such as the
underside of a table.
Mounting to the Underside of a Table
Mounting onto a Rack Rail
Using two mounting screws (not included), mount the left or right mounting ange of the device
onto the front or rear rail of a rack.
Mounting onto a Rack Rail
DO Check the Box
QTY PRODUCT COLOR PART NUM.
1 Cable, RJ-45 Male - DB9 Female, 6' (1.83 m) 2043246
1Connector, 4-Pin 2003576
2Connector, 5-Pin 2003577
1 Power Cord, 5' 10" (1.78 m) 2042043
1 Power Pack, 24 Vdc, 2.5 A, 100-240 Vac 2045873
24 Vdc from
power pack
(included)
To/from
RS-232
device
Ground
To IR
controllable
devices
To/from
serial port
on PC
(cable included)
To/from
USB port
on PC
To
HDMI®
display
From HDMI
audio/video
sources
Balanced/
unbalanced
stereo line
level audio
input
To DM IN
port of
DigitalMedia™
SFP+ receiver†
10BASE-T/
100BASE-TX/
1000BASE-T
Ethernet to
LAN or local
network device*
*To connect to the LAN, use either the LAN port of the DMF-TX-4K-SFP or the LAN port of the DigitalMedia SFP+
receiver (DMF-RMC-4K-SFP or DMCF-RX-4K-SFP)—do not connect the transmitter and receiver LAN ports to the
LAN simultaneously.
†Use Crestron®SFP+ transceiver modules only. Refer to the SFP-10G Series DO Guide (Doc. 7862) for
additional information.

DO GUIDE DOC. 7904B (2046658) 09.16
Specications subject to change without notice.
DO Congure the Device
NOTE: If the HDMI®input of the DMF-TX-4K-SFP connects to a DigitalMedia™ switcher, the
switcher automatically congures the IP table of the DMF-TX-4K-SFP according to the SIMPL
program. The DMF-TX-4K-SFP hosts the conguration settings of the connected receiver
(DMF-RMC-4K-SFP or DMCF-RX-4K-SFP).
If the DMF-TX-4K-SFP connects to a DigitalMedia SFP+ receiver (DMF-RMC-4K-SFP or
DMCF-RX-4K-SFP) in a stand-alone conguration, congure the DMF-TX-4K-SFP using the web
interface. To access the web interface, open a web browser and then go to the IP address of
the device.
NOTE: By default, DHCP is enabled. To display the IP address on the connected display, press
the SETUP button on the top panel of the DMF-TX-4K-SFP.
To log in to the web interface, enter the user name and password. The default user name is
admin, and the default password is admin.
NOTE: The DMF-TX-4K-SFP also hosts the routing, input, and output conguration of the
connected receiver.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The products are Class 1 laser products. They comply with safety regulations of IEC-60825-1,
FDA 21 CFR 1040 11 and FDA 21 CFR 1040 10.
WARNING: Visible and invisible laser radiation when open. Avoid direct exposure to beam.
The specic patents that cover Crestron products are listed at http://www.crestron.com/legal/patents. The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, and DigitalMedia are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDMI and the HDMI logo
are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used
in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not
responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.