Crestron DigitalMedia 8G+ DM-TX-201-C Dimensional drawing

DO GUIDE
DO Connect the Device
Connect the device as required for the application.
Front Panel Connections
NOTE: The DM OUT port is a PoDM (Power over DM) and HDBaseT®PoE (Power over Ethernet)
PD (Powered Device) port. To receive PoDM or HDBaseT PoE, the DM-TX-201-C requires a
connection to a DM®switcher or other equipment that has a PoDM or HDBaseT PoE PSE (Power
Sourcing Equipment) port. Any wiring that is connected to a PoDM or HDBaseT PoE PSE port is for
intrabuilding use only and should not be connected to a line that runs outside of the building in which
the PSE is located.
Rear Panel Connections
DO Check the Box
QTY PRODUCT PART NUM.
1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2045865
DM-TX-201-C
DigitalMedia 8G+®Transmitter 201
DO Mount the DM-TX-201-C
The Crestron®DM-TX-201-C can be mounted onto a at surface or onto a rack rail.
Mounting onto a Flat Surface
Using four mounting screws (not included), mount the device onto a at surface such as a wall or a
ceiling.
Mounting onto a Rack Rail
Using two mounting screws (not included), mount the left or right mounting ange of the
DM-TX-201-C onto the front or rear rail of a rack.
USB HID:
From USB HID
compliant host
or from TT-100
series device
HDMI IN:
From
HDMI
audio/video
source
RGB IN:
RGB or
component
video input
AUDIO IN:
Unbalanced
stereo line level
input
HDMI OUT:
To HDMI®
display
LAN:
10BASE-T/
100BASE-TX
Ethernet to/from
local network device
DM OUT:
To DM®switcher,
receiver, or other
DM device or to
HDBaseT®device
PWR
24 VDC
0.75A:
From included
power pack
Ground

DO GUIDE DOC. 7719B (2042532) 03.17
Specications subject to change without notice.
DO Set the IP Address
The conguration of the DM-TX-201-C within the DM 8G+®system determines how the IP address of
the DM-TX-201-C is set:
• If the DM-TX-201-C connects to a DM switcher, the DM-TX-201-C is congured by the switcher
automatically.
• If the DM-TX-201-C connects to a DM 8G+ receiver, the DM-TX-201-C uses its own
conguration settings. By default, DHCP (Dynamic Host Conguration Protocol) is enabled.
If assignment of the default IP address is desired, hold down the SETUP button while the unit
boots up. The default IP address, which is 192.168.1.236, overwrites the current setting.
To manually set a different IP address, use the Crestron Toolbox™ application.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics 15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
This product is Listed to applicable UL®Standards and requirements tested by Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specic patents that cover Crestron products are listed at http://www.crestron.com/legal/patents. The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia 8G+, DM, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or
other countries. HDBaseT is either a trademark or registered trademark of the HDBaseT Alliance in the United States and/or other countries. HDMI is either a trademark or registered trademark
of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States
and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.