DO GUIDE
DM-TX1- 4K-C-1G
Wall Plate 4K DigitalMedia 8G+™ Transmitter
DO Make Connections
to the Rear Panel
Make connections to the rear panel of the
Crestron®DigitalMedia 8G+™
DM-TX1-4K-C-1G before mounting the unit
into an electrical box. If the unit is to be
mounted under a table or onto a at surface
or rack rail, make connections to the rear
panel after the unit is mounted. (For mounting
instructions, refer to the “DO Mount the
DM-TX1-4K-C-1G” section in this guide.)
NOTE: The DM OUT port is a PoDM (Power
over DM) and PoH (Power over HDBaseT)
PD (Powered Device) port. To receive PoDM
or PoH, the DM-TX1-4K-C-1G requires a
connection to a DigitalMedia™ switcher or
other equipment that has a PoDM or PoH
PSE (Power Sourcing Equipment) port. Any
wiring that is connected to a PoDM or PoH
PSE port is for intra-building use only and
should not be connected to a line that runs
outside of the building in which the PSE is
located.
DO Mount the
DM-TX1-4K-C-1G
Mount the DM-TX1-4K-C-1G onto a rack rail,
into an electrical box, under a table, or onto a
at surface as appropriate for the installation.
Mounting onto a Rack Rail
The DM-TX1-4K-C-1G mounts onto the front
or rear rail of a rack.
To mount the unit onto a rack rail, do the
following:
1. Position the DM-TX1-4K-C-1G
horizontally so that the holes in the left
or right mounting ange align with the
holes in the rack rail.
2. Secure the unit to the rack rail using two
mounting screws (not included).
Mounting into an Electrical Box
The DM-TX1-4K-C-1G mounts into a 1-gang
electrical box (not included). A minimum
mounting depth of 3 1/2 inches (89 mm) is
required.
To mount the DM-TX1-4K-C-1G into an
electrical box, do the following:
1. Using a Phillips head screwdriver, attach
the DM-TX1-4K-C-1G to the electrical
box using the two included 6-32 x 3/4
inch truss combo head screws.
2. Attach a decorator-style faceplate
(not included) to the front panel of the
DM-TX1-4K-C-1G using two screws
(not included).
Mounting under a Table or onto a
Flat Surface
The DM-TX1-4K-C-1G mounts under a table
or onto a suitable at surface using the
included surface mount bracket.
To mount the unit under a table or onto a at
surface, do the following:
1. Using a Phillips head screwdriver, attach
the included surface mount bracket
to the DM-TX1-4K-C-1G using the two
included 4-40 x 1/4 inch SEMS screws.
2. Attach the bracket to the underside of
a table or onto a at surface using two
mounting screws (not included).
DO Check the Box
QTY PRODUCT PART NUM.
1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2037285
2 Screw, 6-32 x 3/4” L, Steel, Truss, Combo Head 2009211
1Surface Mount Bracket 2016054
2 Screw, 4-40 x 1/4” L, Pan Head, Steel, SEMS with Washer 2007153
1Interface Connector, Plug, 2-Pin 2003574
Not Included: Electrical Box, Phillips Head Screwdriver, Decorator-Style Faceplate and Screws, Cables, Rack Mount Screws, and Table or Surface
Mount Screws
24 Vdc from
Power Pack
(Included)
Ground
To DM®Switcher,
Receiver, or Other
DM Device or to
HDBaseT®Device
DM OUT
