Crosley CO1011A User manual

C R O S L E Y
F U R N I T U R E
METAL SIDE TABLE
CO1011A

C R O S L E Y
F U R N I T U R E
Congratulations! You have purchased a stylish piece of Crosley Furniture. We strive
to provide fine furniture products, built with quality materials. Please carefully follow
the assembly instructions to ensure your furniture is assembled correctly to provide
long lasting enjoyment.
Should you experience any missing or damaged parts, do not return to the store.
Please contact us directly at 800-815-4796.
Care: Use a soft clean cloth that will not scratch the surface when dusting. Use of
furniture polish is not necessary. Should you choose to use polishes, test in an
inconspicuous area first. Use of solvents of any kind may damage your furniture's
finish. To clean, simply use a soft clean cloth moistened with lukewarm water, then
buff with a dry soft clean cloth.
1 of 5

2 of 5
PART LIST
A B C
1PC 3PC 1PC
HARDWARE LIST
12345
1/4" NUT
HEX WRENCH
BOLT COVER
1/4" X 15 MM BOLT E6.5 X 1.0 MM
WASHER
6 7 8
3 PCS 3 PCS 3 PCS
3 PCS
1 PC 1 PC 3 PCS
ST4.2 X 33 MM
BOLT
6 PCS
Allen Wrench FOOT CAP
FACTORY ASSEMBLY
Head Screw Driver(Not included)
Tools needed: Allen key(part#6) and Hex Wrench(part#7) (Included) Phillips
TOP LEG Leg Connector

3 of 5
Step1: Place tabletop upside down on a flat, non-abrasive surface. Attach table leg to
tabletop using 1/4"x 15mm bolt (1) and 1/4" (2) washer as shown in (Figure 1).
Add 1/4" nut (4) to the end of bolt. Tighten a few revolutions only. Do not tighten
completely at this time as some adjustments may be necessary to the alignment
of the table legs. Repeat for remaining two legs.
1
6
4
Figure 1
2
A
B
Step2: Insert table leg connector ( C) in the center of the three legs as shown in Figure 2.
Secure by inserting two ST4.2 x 33mm bolt (5) through the two holes in the center of
the leg and into the leg connector as shown in (Figure 3). Tighten a few revolutions
only. Do not tighten completely. Repeat for remaining two legs.
C
Figure 2
3
7

4 of 5
Step3: Make any adjustments to the parts to ensure they are properly aligned. At this time
tighten all nuts and bolts using Allen Wrench (6) and hex wrench (7). Tighten each
bolt connection a few revolutions at a time, rotating between bolt connections until
all nuts and bolts are completely tightened. DO NOT OVER TIGHTEN. Cover bolts
with PVC bolt covers. Turn table into the upright position.
YOUR TABLE IS NOW READY FOR USE.
Figure 3

C R O S L E Y
F U R N I T U R E
Limited Manufacturers Warranty
Crosley Furniture Products are warranted against defects in material and
workmanship for a period of 90 days beginning from the date of sale. Should any
parts be missing or defective, we will replace or repair the parts for a period of 90 days
from the date of purchase.
Should you experience any missing or damaged parts, do not return to the store. Please
contact us directly at 800-815-4796 from 9 AM to 5 PM (EST) Monday to Friday.
This warranty gives the purchaser specified legal rights in addition to any rights
which may vary from state to state.
In accordance with the "Moss-Magnuson Warranty Act" of July 10, 1975, this is termed
a "limited warranty" which in no way compromises Crosley Furniture's high standards
of Quality and Workmanship.
5 of 5