Crosswater Classic Console Series User manual

Installation Instructions
Tape
measure
Safety
glasses
Hammer Flat head
screwdriver
1/4”
drill
Pencil Spirit
level
Tools required
Floor nipples
x2
Rubber washers
x4
x7
x6
Floor nipple washers
x6
x2
x2
x1
x2
Installation notes
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
Assemble the parts on a mat to protect against scratching the surface.
Avoid getting cement, grit, sand or masonry products on to the surface.
Protect and cover the basin during the installation period to prevent
damage from occurring.
IMPORTANT: Turn off the main water supply before connecting to
any existing pipework or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise,before drilling holes in a wall or floor.
Introduction
All parts have been fully inspected throughout the production
process and only leaves our factory after a 15-step QC process.
Carefully remove the items from the box and check that all parts have
been supplied.
Installation should be completed by at least two suitably competent
installers
Before beginning installation, please check for any damage that may
have occurred during transport. Note: Damage claims cannot be
made during or after installation.
Improper installation shall result in loss of warranty in case of
damage caused by impacts or rubbing against rough surfaces.
Wall fixings are not supplied. Source fixings which are suitable to the
site wall.
IMPORTANT: Please read these instructions carefully before
beginning and retain for future reference.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Classic Console US-B15/US-T49
Classic Pedestal Basin US-B15/US-P6
Parts supplied - basin stand

NOTE: At this stage, if you are using the US-T49 basin stand
extension kit (sold separately), refer to step 5 and then
proceed to step 6.
2 3/8”
1Installation - basin stand
2
4 5
3
Please make sure you have the correct basin suitable for the basin legs, US-B15 is recommended.
Attach the two horizontal rails to the front rail. Attach both feet to the legs.
Screw the legs into the rail. If the US-T49 basin stand extension kit is being installed,
please refer to the illustration shown below. The kit will raise
the final height of the basin by 2-3/8".

x4
1/4”
1/4”
1/4”
Fix the oor nipples onto the
oor. There are 6 oor nipple
washers supplied. These can
be inserted onto the oor nipples
to adjust for an uneven oor.
6 7
Check that the horizontal bracket bar is vertical using a spirit
level.
Determine the nal installation position and mark the 4 wall
and two oor xing hole positions in pencil. Please make sure
to include the floor nipples (and washers if necessary) when
determining the installation position because the stand may
elevate after the oor nipples are tted.
8 9
Using a 1/4”drill bit,drill the six holes on the marked
positions.
Fit the two legs over the oor nipples.

Issue date: 05122019
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
The top part of the rail
can be adjusted slightly
if the basin is not level.
1Installation - pedestal
2Installation
10 11
Fix each of the two brackets onto the wall.
Ensure that the screw heads are parallel to the floor.
Place 4 rubber washers into the 4 recesses as shown.
Place the basin in position ensuring that it is level. The basin
must be fixed to the wall at the rear using appropriate wall
fixing screws. For a marble basin, please refer to installation
instructions that come with the basin.
lPlace the basin in position, against the wall and sitting on top of the
pedestal.
lEnsure that the basin is level and then mark the required fixing hole
locations on the wall, then proceed to drill.
lUsing appropriate fixings, attach the basin to the wall securely.
lThe pedestal under the basin is for decoration only and is not
designed to support the weight of the basin.
A simple routine of regular care will keep your vitreous china and fireclay products clean and fresh.
Rinse away any traces of soap and gently dry with a clean soft cloth after each use. A mild detergent, warm water and a soft cloth will remove
normal dirt and soap accumulations from surfaces. Soft abrasive cleaners may be used on vitreous china and fireclay. Never use abrasive
cleaners without water. Do not use caustic cleaners or disinfectants as they can alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass cleaners to
remain on the surface. Prolonged contact can alter surface finishes and void the warranty.
3 Cleaning Instructions
Note: We recommend that the 4 rubber washers
are not to be used if installing a marble basin on to
the stand.
Length and width dimensions
are measured at the narrowest
part of the opening:
L 4-1/2", W 3", H 25-3/4"