Crosswater US-PRO120 User manual

Installation Instructions
4”
5-1/2"
Finished wall
2-1/4" 5-7/8"
8-5/8"
9”
3-3/4"
1-1/4"
3"
Adjustable
wrench
Channel
locks
Plumbers’ putty
or caulking
Flat head
screwdriver
Cross head
screwdriver
Hexagonal
key
Flow rate (PSI)
Flow rate (GPM)
100
0
0.2
0.4
0.6
0.8
1.0
1.2
20 30 40 50 60 70 80
MPRO Wall-mount Single-lever
Basin Faucet Trim
US-PRO120
Introduction
Installation notes
The faucets in this range are single flow (hot and cold water mix in the
body) and should therefore be supplied with hot and cold water at
balanced pressures. If the faucets are not supplied at balanced
pressures then the mixer will not function correctly.
The minimum water pressure required for these faucets is 20 psi. The
maximum water pressure is 60 psi beyond which pressure-reducing
valves must be JOTUBMMFE.
The faucets are fitted with quarter-turn ceramic disc cartridges which
provide a good flow rate with very smooth movement.
IMPORTANT: Please read these instructions carefully before you
begin and retain for future reference. These instructions have
been prepared for your guidance, you must exercise due care at
all times.
#FGPSFCFHJOOJOHJOTUBMMBUJPODIFDLGPSBOZEBNBHFUIBUNBZIBWF
PDDVSSFEEVSJOHUSBOTQPSU/PUF%BNBHF DMBJNTDBOOPUCF NBEF
EVSJOHPSBGUFSJOTUBMMBUJPO
We do not accept responsibility for any problems that may occur
due to incorrect installation.
Dimensions
Tools required
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
Install the US-120ROUGH first using the installation instructions
provided with it before following the trim installation detailed
below.
8"3/*/(#FGPSFJOTUBMMJOHBOFXGBVDFUJUJTFTTFOUJBMUIBUUIFTVQQMZ
QJQFTBSFUIPSPVHIMZGMVTIFEJOPSEFSUPSFNPWFBOZSFNBJOJOHEFCSJT
TPMEFSPSPUIFSJNQVSJUJFT'BJMVSFUPDBSSZPVUUIJTTJNQMFQSPDFEVSFDBO
DBVTFQSPCMFNTPSEBNBHFUPUIFXPSLJOHPGUIFGBVDFU
Installing shut-off valves on incoming supply lines is recommended for
ease of maintenance.
Turn off the main water supply before connecting to any existing
pipework or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric or
otherwise, before drilling holes in a wall or floor.Flow rate

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
Issue date: 15092019
COLLAR
AERATOR
Replacement part
US-AERPROWS
CARTRIDGE
Replacement part
US-MCAR120
COVER
HANDLE
HEXAGONAL
KEY
COVER
PLATE
RETAINING
NUT
COVER
CAP
VALVE
BODY
COVER
PLATE SPOUT
Use
teflon tape
for seal
COVER PLATE
HANDLE
HEXAGONAL
KEY
COVER
CAP
lShut off the water heating system then, with the main water
supply turned o, open the lowest hot and cold faucets and
allow to drain until supply pipes are empty.
For valve body fitting,see installation instructions for
US-120ROUGH before following the trim installation detailed
below.
Spout
NOTE: Two lengths of spout are provided to suit individual
installations, (short spout illustrated).
lOnce the spout selection is made,apply a narrow bead of
caulking to the back edge of the cover plate and place
around the main outlet.
lAttach selected spout and tighten until spout is vertical.
lUse teflon tape to achieve a watertight seal.
Handle
lApply a narrow bead of caulking to the back edge of the cover
plate and press into position.
lPlace the handle onto the cartridge spline and secure using a
hexagonal key.
lPush-fit the cover cap.
ATTENTION: Check all new connections for leaks.
lTurn on the main water supply, close all faucets except the new
mixer and as the system refills, check for leaks.
lOnce satisfied there are no leaks, switch on the heating system.
Installation
Cleaning the cartridge
lThe concealed cartridge should give trouble-free service
however servicing is a straightforward process.
To remove the cartridge
lWith the water supply turned o, carefully remove the cover cap
and using a hexagonal key loosen the screw but do not remove.
lPull off the handle and unscrew the cover.
lUsing a 7/8” wrench, unscrew and remove the cartridge.
lWash the cartridge with clean running water, dry and lightly grease
the seal, (only use silicone grease).
lReplace the cartridge followed by the nut, cover and handle.
Maintenance
Spout
Handle
3 Cleaning Instructions
Rinse away any traces of soap and gently dry with a clean, soft cloth after
each use. Rinse completely with water and dry any overspray.
This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water.
Do not allow the solution to soak on the product.
Simichrome Polish® contains a protective film to enhance maintenance and
is helpful in preventing water spot buildup. Follow instructions to ensure
optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the
surface. The use of abrasive cleaners, cleansers or disinfectants will alter the
surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream,
nail polish remover, vinegar, wine, drain and glass cleaners to remain on the
surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can
cause damage to the finish.
Please see the website for care instructions for specific finishes.