Crosswater INFINITY 500mm FURNITURE User manual

Measurements in millimetres mm
Informaon updated July 2020
Tel [phone]
INFINITY 500mm FURNITURE
TECHNICAL DATA SPECIFICATION
CODE No UNIT IF5000Dxx
Installation Information:
Required top Worktop see prevailing Crosswater catalogue
Recommended use: Domestic, residential
Dimension Unit w 500 x d 450 x h 450mm
Installation: Wall Hung Furniture Colours:
Materials: Carcass and drawer front 18mm MDF Black Matt IF5000DBM
EN622 type 5
Drawer set 18mm MDF Storm Grey Matt IF5000DSG
EN622 type 5
Specification: Full extension soft close drawers - 30kg weight capacity White Gloss IF5000DWG
EN622 type 5
Anti-tip wall hangers 170Kg capacity Windsor Oak IF5000DWO
EN622 type 5
Weight: 21kg
Fitting: Wall hangers integrated into carcass Handle Colour options:
Wall brackets supplied IF_HANDLEC Chrome
Required Fitting: Compatbile to basin requirement IF_HANDLEBM Matt Black
Advised Fitting: Space saving 50mm seal trap BTR0510W IF_HANDLEF Brushed Brass effect
Option Accessories: Handles - see right. Interior drawer and LED light bar IF_HANDLEV Stainless Steel Effect
Warranty 10 years on furniture
The intended installation wall needs to be strong
enough for the weight of the furniture and basin. Wall
fixings for solid walls included.
Laminate finishes/lacquer tested to ISO 22196
Measurement of antibacterial activity Graded Strong
value of anit-bacterial effect A>3

Measurements in millimetres mm
Informaon updated July 2020
Tel [phone]
INFINITY 500mm FURNITURE
TECHNICAL DATA SPECIFICATION
CODE No UNIT IF5000Dxx
Installation Information:
Required top Worktop see prrvailing Crosswater catalogue
Recommended use: Domestic, residential
Dimension Unit w 500 x d 450 x h 450mm
Installation: Wall Hung Furniture Colours:
Materials: Carcass and drawer front 18mm MDF Black Matt IF5000DBM
EN622 type 5
Drawer set 18mm MDF Storm Grey Matt IF5000DSG
EN622 type 5
Specification: Full extension soft close drawers - 30kg weight capacity White Gloss IF5000DWG
EN622 type 5
Anti-tip wall hangers 170Kg capacity Windsor Oak IF5000DWO
EN622 type 5
Weight: 21kg
Fitting: Wall hangers integrated into carcass Handle Colour options:
Wall brackets supplied IF_HANDLEC Chrome
Required Fitting: Compatbile to basin requirement IF_HANDLEBM Matt Black
Advised Fitting: Space saving 50mm seal trap BTR0510W IF_HANDLEF Brushed Brass effect
Option Accessories: Handles - see right. Interior drawer and LED light bar IF_HANDLEV Stainless Steel Effect
Warranty 10 years on furniture
The intended installation wall needs to be strong
enough for the weight of the furniture and basin. Wall
fixings for solid walls included.
Laminate finishes/lacquer tested to ISO 22196
Measurement of antibacterial activity Graded Strong
value of anit-bacterial effect A>3
Plan View
Side View—drawer extension

BATHROOM FURNITURE RANGE
IMPORTANT - Advice and safety - Please read before installation
INFINITY
Tools & equipment needed: Drill, 8mm Suitable drill bit, Screwdriver, Spirit level, Ruler/tape measure, Pencil, Silicone sealant (clear).
In!nityFurniture
Please read these instructions carefully before starting
installation and keep in a safe place for future reference.
Check the contents of the pack carefully before installation.
Crosswater will not be held responsible for any de-fit / re-fit costs
where faulty product has been fitted.
If any fault is found with materials or workmanship, it must be
reported immediately to the manufacturer. Remedial action will
be taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer; 2. The product
has not been modified or tampered with; 3. The manufacturer is
informed of any damage/shortages prior to installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Advice & Safety
This product should only be installed by a suitably qualified
Plumber/installer. Should the installation be completed by a
non-qualified person any product guarantee maybe considered
invalid. For a claim made under our warranty written certification
of your installers qualifications can be required.
It is advised that all doors and drawers are removed prior to
fitting to avoid unnecessary damage occurring.
Ensure the room is well heated and ventilated.
It is recommended that walls are fully tiled before furniture and
accessory installation. This ensures that the product is installed
flat to the tile face and allows product to be easily removed if
required in the future.
These instructions have been prepared for your guidance, you
must exercise due care always.
Please note that some units are heavy. Always take care when
lifting, and follow health and safety guidelines. It is recommended
that 2 people carry out the installation of larger basin/vanity units.
Warning" ! Please check for any hidden pipes or electrical cables
before drilling holes in the floor or walls.
When using power tools always follow the manufacturer’s user
instructions.
Do not over tighten tap or waste fittings, doing so may result in
damaging the basin.
The vanity units CAN ONLY BE installed using the fitting brackets
supplied. Before installing a wooden bathroom product into a new
property, extension or recently plastered room we strongly advise
the building/room is completely dry, well ventilated and adequately
heated prior to installation.
Care & Cleaning.
NEVER use products containing bleach, cleaners of a gritty or
abrasive nature or so called “glass and mirror” cleaning products.
Use a well wrung chamois leather or microfiber cloth for furniture
carcasses.
Ceramic fine fire clay wash basins should only be cleaned with a
mild detergent or warm soapy water; in hard water areas a good
quality limescale remover can be applied.
If any maintenance is required, then it must be carried out by a
qualified Plumber.
1
500 Basin Unit
x8
IF5000D
x2
200 Basin Unit
x4
x2
IF2052
IF5100T+
IF9100T+
IF7100T+
IF1010T+
IF1210T+
To ensure full working use of the
drawers we recommend the use of
basin furniture trap BTR01410W.
20Kg 12Kg
4Kg
6Kg
7Kg
8Kg
9Kg
10Kg
510mm
710mm
910mm
1010mm
1210mm
1410mm
Worktop
x2
IF1410T+

2
In•nity Furniture
INSTALLATION INSTRUCTIONS
One Drawer Basin Unit & Basin Installation - 500 Basin Unit
Step 1
Step 3
Step 2
Pull out the drawer to its full extension, gently squeeze the locking levers
outwards on both sides and pull the drawer off the runners at the front.
Plan unit position
Decide on the position and height of the
unit.The recommended basin height es
between 860mm and 870mm from floor
to top of basin.
X
a/ Base Unit 200 a/ Base Unit 500
‘Wall bracket’ installation
a: Place unit in the required position.
b: Mark the bracket fixing holes onto the wall. Drill Ø 8mm holes, insert the wall plugs supplied on solid walls, use suitable wall fixings
for dry-wall (not supplied).
Important: If the basin unit and/or basin are not fitted level this may result in the basin not draining correctly.
Remove the drawer
before installa!on.
Remove the drawer
Removing bracket
from the wall
b / Base Unit 200b / Base Unit 500
weight capacity per set
of brackets is 172Kg
weight capacity per set
of brackets is 154Kg

3
In•nity Furniture
Step 4
Step 7
Important: All cut edges MUST be
sealed with water proof sealant or
exterior wod vernish.
Note: Basin waste and taps fittings when over tightened can create stress
within the basin material which may in time cause the failure of the product.
Waste fittings should be carefully bedded in silicone and the back-nut
hang tightened an additional quarter turn using a suitable spanner is sufficient
to create the required water light seal. Care should also be taken when fitting
brassware to tap platforms in order to prevent similar stress related failures.
Step 5
Worktop / Basin Installation
a: Prepare worktop for tap/s
and basin. Cut holes where
required using a suitable
sized hole cutter.
b: Carefully apply silicone to
the top edges of the unit.
c: Carefully position the
worktop down onto the
unit, ensure it is centrally
positioned and flush at the
back.
Connect the tap and waste.
Apply silicone to the join
between the worktop and
wall, down sides of the unit
and around the base of the
basin.
Leave silicone, 24 hours to
dry.
Step6
Attach drawer handle
(should be after re-fit drawer
but before drawer adjustment)
(pre-fitted on inside of drawer)
Attach the handle to the
drawer front.
Re-•t drawers:
(should be after furniture assembly below
but before drawer adjustment)
1: Pull drawer runners fully out.
2: Set the drawer down onto the runners.
3: Push the drawer fully in.
Test to make sure the drawers operate
correctly and there are no obstructions
behind the drawer.
The internal drawer is optional and should
be installed before the worktop is fitted.
Please installation guide supplied with the
product.
a b c

4
INBATHROOM FURNITURE ASSEMBLY
HANGING THE FURNITURE
When installing two or more units, ensure the units are correctly positioned side by side, front to back and in
height - the base of each unit should be level as shown in examples below.
20+50 50+20+50
The internal carcass sides are pre-drilled for installing adjoining units as shown below
50+50
Using connector bolts provided secure the adjoining units
In!nity Furniture

DRAWER RUNNER ADJUSTMENT
Le•/Right adjustment
Max. + 3.5 mm
Move the green tab until the front tilt is adjusted.
Max. + 4.0 mm
Turn the green wheel up to adjust right and down
to adjust left.
Max. ± 1.5 mm
Step 1
Step 2
Step 3
Front tilt adjustment
Front height adjusment
Each drawer is fully aligned and tested during production. If adjustment is required please follow the gui-
delines below:
The weight capacity for drawer is 40Kg

For any further information please contact
Crosswater on: 0345 873 8840
Or visit our web-site at:
www.crosswater.co.uk
The manufacturer reserves the right to make technical
modifications without prior notice.
Fitting of Tiled Drawer fronts
STEP 1: Removal of pre-fitted drawer
a Remove the inside cam bolts as shown below
b Remove cam bolt on drawer underside as shown
The front can now be removed.
STEP 2: Fitting of tiled drawer front
Insert the front panel onto the drawer sides secure in place
a. Secure side cambolts !rst
b. secure underside cambolt
c. replace drawer correctly in carcass
ab
c

BATHROOM FURNITURE RANGE
IMPORTANT - Advice and safety - Please read before installation
INFINITY
Tools & equipment needed: Drill, 8mm Suitable drill bit, Screwdriver, Spirit level, Ruler/tape measure, Pencil, Silicone sealant (clear).
In!nityFurniture
Please read these instructions carefully before starting
installation and keep in a safe place for future reference.
Check the contents of the pack carefully before installation.
Crosswater will not be held responsible for any de-fit / re-fit costs
where faulty product has been fitted.
If any fault is found with materials or workmanship, it must be
reported immediately to the manufacturer. Remedial action will
be taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer; 2. The product
has not been modified or tampered with; 3. The manufacturer is
informed of any damage/shortages prior to installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Advice & Safety
This product should only be installed by a suitably qualified
Plumber/installer. Should the installation be completed by a
non-qualified person any product guarantee maybe considered
invalid. For a claim made under our warranty written certification
of your installers qualifications can be required.
It is advised that all doors and drawers are removed prior to
fitting to avoid unnecessary damage occurring.
Ensure the room is well heated and ventilated.
It is recommended that walls are fully tiled before furniture and
accessory installation. This ensures that the product is installed
flat to the tile face and allows product to be easily removed if
required in the future.
These instructions have been prepared for your guidance, you
must exercise due care always.
Please note that some units are heavy. Always take care when
lifting, and follow health and safety guidelines. It is recommended
that 2 people carry out the installation of larger basin/vanity units.
Warning" ! Please check for any hidden pipes or electrical cables
before drilling holes in the floor or walls.
When using power tools always follow the manufacturer’s user
instructions.
Do not over tighten tap or waste fittings, doing so may result in
damaging the basin.
The vanity units CAN ONLY BE installed using the fitting brackets
supplied. Before installing a wooden bathroom product into a new
property, extension or recently plastered room we strongly advise
the building/room is completely dry, well ventilated and adequately
heated prior to installation.
Care & Cleaning.
NEVER use products containing bleach, cleaners of a gritty or
abrasive nature or so called “glass and mirror” cleaning products.
Use a well wrung chamois leather or microfiber cloth for furniture
carcasses.
Ceramic fine fire clay, solid surface wash basins and worktops
should only be cleaned with a mild detergent or warm soapy
water; in hard water areas a good quality limescale remover can
be applied.
If any maintenance is required, then it must be carried out by a
qualified Plumber.
1
500 Basin Unit
x8
IF5000D
20KGS
x2
200 Basin Unit
x4
x2
IF2052
12KGS
To ensure full working use of the
drawers we recommend the use of
basin furniture trap BTR01410W.
Worktop
x2
IF1410T+
1410mm 10Kg
IF5000D
20KGS
IF1010T+
1010mm 8Kg
IF9100T+
910mm 7Kg
IF7100T+
710mm 6Kg
IF5100T+
510mm 4Kg
IF1210T+
1210mm 9Kg
Worktop
IF05000SPW
9kg
IF0700SPW_LH
13Kg
IF0700SPW_RH
13kg
IF09000SPW
16Kg
IF1000SPW
18Kg
IF1000SPW_RH
18Kg
IF1000SPW_LH
18Kg
IF12000SPW
21Kg
IF1200SPW_RH
21Kg
IF1200SPW_LH
21Kg
IF14000SPW
26Kg

2
In•nity Furniture
INSTALLATION INSTRUCTIONS
One Drawer Basin Unit & Basin Installation - 500 Basin Unit
Step 1
Step 3
Step 2
Pull out the drawer to its full extension, gently squeeze the locking levers
outwards on both sides and pull the drawer off
the runners at the front.
Plan unit position
Decide on the position and height of the
unit.The recommended basin height es
between 860mm and 870mm from floor
to top of basin.
X
a/ Base Unit 200 a/ Base Unit 500
‘Wall bracket’ installation
a: Place unit in the required position.
b: Mark the bracket fixing holes onto the wall. Drill Ø 8mm holes, insert the wall plugs supplied on solid walls, use suitable wall fixings
for dry-wall (not supplied).
Important: If the basin unit and/or basin are not fitted level this may result in the basin not draining correctly.
Remove the drawer
before installa!on.
Remove the drawer
Removing bracket
from the wall
b / Base Unit 200b / Base Unit 500
weight capacity per set
of brackets is 172Kg
weight capacity per set
of brackets is 154Kg