Crosswater Leyden 14X-03-T User manual

Applicable Standards/Codes
14-03-PC
14-03-SN
14-03-PN
14-03-BZ
15121442-A 4
Installation Dimensions
15121442-A
For ease of installation you will need:
●To read the installation instructions completely before beginning.
●To read all warnings, care, and maintenance information.
IAPMO certified to meet or exceed the following:
• ASME A112.18.1/CSA B125.1
• Uniform Plumbing Code
• National Plumbing Code of Canada
• ADA Compliant
2 1/8＂
3 1/4＂4 5/16＂
3 7/16＂2 9/16＂
8 15/16＂
1 3/16＂
2 1/8＂
9 5/8＂
9 1/16＂
5 1/2＂
7 5/8＂
7 5/16＂
3/4＂-14 NPT
19" Max 19" Max
1 15/32＂
1 1/16＂-1 9/16＂
2 1/8＂MAX
1 3/16＂
19 11/16" 59 1/16"
Leyden Deck-mount Tub Faucet with Handshower Trim
14X-03-T
Installation Instructions
Before beginning installation, check for any damage
that may have occurred during transport.
Note: Damage claims cannot be made during or
after installation.
Anti-scald protection is the responsibility of the installer and
according to applicable codes.

14X-03-T
Installation Instructions
15121442-A 2 15121442-A3
Replacement Parts
NO. Description Part NO.
1
Diverter Knob & Rod Assembly
9Q1108
2
3
Deck Spout Set Screw & Allen Key 9Q1350NT
4
Handle Assembly 9Q1109
5
Washer, Key & Aerator 9Q1110PL
6
Washer 51011909PL
7
Hand Shower Set Screw & Allen Key 9Q1349NT
Hand Shower 5F0M0178
● Only use a soft, dampened sponge or cloth to clean and polish the fixture.
● Wipe fixtures and the immediate areas clean and rinse completely with water immediately after installation and after
applying any cleaner.
● If you are using a cleaning compound on or close to the product, please test the compound on a hidden area of the
trim to ensure it will not damage the finish.
● Do not allow cleaners to soak anywhere on the product.
Cleaning Instructions
123
4 5
Turn the water supply off and remove
the mud guards.
Pull black nylon or finished hose
through the hand shower nipple
bracket. Slide the hand shower “O”
ring, bracket and hose guide over the
hose. Secure the assembly with the
setscrew. Note, make sure the hose
does not slip under the deck.
6
Place the spout washer under the
spout and install spout on spout
nipple-diverter assembly. Be sure the
spout is firmly resting on the deck.
Secure the spout with the setscrew.
Insert diverter knob and rod assembly
into the spout and thread the
assembly onto the diverter rod in the
spout diverter assembly. Pull the
diverter rod and knob up and down to
test the connection.
Place the “O” ring over the cold valve.
Align the handle and place the handle
and escutcheon assembly into the
valve. Secure the assembly by turning
the escutcheon clockwise. Repeat for
hot valve.
Remove the aerator with the supplied
key. Turn the water supply on.
1
34
5
7
6
2
7
Make sure the diverter knob is in the
down position. Turn the faucet
handles on full for one minute to flush
debris.
8
Leaving the water on, pull the hose
to its farthest extension and point it
into the tub. Pull the diverter knob to
its top position. Flush the debris fro
one minute. Turn off the valves.
9
Attach the hand shower to the black
nylon or finished hose.
10
Re-install the aerator with key.
11
Installation complete.
Note: For illustration purposes, lever handle version is shown.
Please refer to page 5 for instructions on how to remove the lever handle and install
the cross handle.

14-03-T-PC
14-03-T-SN
14-03-T-PN
14-03-T-BZ
Installation Instructions
15121442-A 2 15121442-A3
Replacement Parts
NO. Description Part NO.
1
Diverter Knob & Rod Assembly
9Q1108
2
3
Deck Spout Set Screw & Allen Key 9Q1350NT
4
Cross Handle Assembly 14-XHDL
5
Washer, Key & Aerator 9Q1110PL
6
Washer 51011909PL
7
Hand Shower Set Screw & Allen Key 9Q1349NT
Hand Shower 5F0M0178
123
4 5
Turn the water supply off and remove
the mud guards.
Pull black nylon or finished hose
through the hand shower nipple
bracket. Slide the hand shower “O”
ring, bracket and hose guide over the
hose. Secure the assembly with the
setscrew. Note, make sure the hose
does not slip under the deck.
6
Place the spout washer under the
spout and install spout on spout
nipple-diverter assembly. Be sure the
spout is firmly resting on the deck.
Secure the spout with the setscrew.
Insert diverter knob and rod assembly
into the spout and thread the
assembly onto the diverter rod in the
spout diverter assembly. Pull the
diverter rod and knob up and down to
test the connection.
Place the “O” ring over the cold valve.
Align the handle and place the handle
and escutcheon assembly into the
valve. Secure the assembly by turning
the escutcheon clockwise. Repeat for
hot valve.
Remove the aerator with the supplied
key. Turn the water supply on.
1
34
5
7
6
2
7
Make sure the diverter knob is in the
down position. Turn the faucet
handles on full for one minute to flush
debris.
8
Leaving the water on, pull the hose
to its farthest extension and point it
into the tub. Pull the diverter knob to
its top position. Flush the debris fro
one minute. Turn off the valves.
9
Attach the hand shower to the black
nylon or finished hose.
10
Re-install the aerator with key.
11
Installation complete.

Applicable Standards/Codes
14X-03-T
15121442-A 4
Installation Dimensions
Series # 14
TRIM ONLY
DeckTub Set with Hand Shower & Diverter Spout Trim
14-03-T-PC
14-03-T-SN
14-03-T-PN
14-03-T-BZ
15121442-A
Installation Instructions
For easy installation of your faucet you will need:
● To read all the installation completely before beginning.
● To read all warnings, care, and maintenance information.
IAPMO certified to meet or exceed the following:
• ASME A112.18.1/CSA B125.1
• Uniform Plumbing Code
• National Plumbing Code of Canada
• ADA Compliant
19" MAX 19" MAX
9-5/8"
9"
7-1/4" 7-5/8"
5-1/2"
3-1/4" 2-1/8"
1-1/2"
3/4"-14 NPT
1" - 1-1/2"
19-3/4" 59"
1-1/2"
2-1/8"
1-1/4"
2-1/8" MAX
9"
1-1/4"
2-1/2"
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and
dry any overspray. This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the
product.
Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup.
Follow instructions to ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners,
cleansers or disinfectants will alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain
and glass cleaners to remain on the surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can cause damage to the finish.
Please see the website for care instructions for specific finishes.
Cleaning Instructions
Issue date: 18112019

2. Take out the screw and lock
washer with a Phillips screwdriver
3. Remove the lever 4. Replace with cross handle
and re-install the screw and
washer
1. Hold the handle escutcheon and turn it counterclockwise to remove
Leyden Cross Handle Installation Instructions
14X-02-T, 14X-03-T,14X-08