Crosswater MPRO US-PRO110 User manual

Installation Instructions
4-3/4"
5-1/2"
15/8”
2-1/2"
1-1/4"
1-3/4"
US-PRO114
6"
6-1/2"
2-3/8"
2-1/2"
1-1/4"
1-3/4"
US-PRO110
US-PRO110-K
6-3/4"
14-1/4"
10-1/8"
2-1/2"
1-1/4"
1-3/4"
US-PRO112
3/4"
3/4”
Adjustable
wrench
Channel
locks
Plumbers’ putty
or caulking
Flat head
screwdriver
Cross head
screwdriver
Hexagonal
key
MPRO Single-hole Basin Faucet US-PRO110 / US-PRO110-K
MPRO Single-hole Mini Basin Faucet US-PRO114
MPRO Vessel Faucet US-PRO112
Introduction
Installation notes
The faucets in this range are single flow (hot and cold water mix in the
body) and should therefore be supplied with hot and cold water at
balanced pressures. If the faucets are not supplied at balanced
pressures then the mixer will not function correctly.
The minimum water pressure required for these faucets is 20 psi. The
maximum water pressure is 60 psi beyond which pressure-reducing
valves must be installed.
The faucets are fitted with half-turn ceramic disc cartridges which
provide a good flow rate with very smooth movement.
IMPORTANT: Please read these instructions carefully before you
begin and retain for future reference. These instructions have been
prepared for your guidance, you must exercise due care at all
times.
Before beginning installation, check for any damage that may have
occurred during transport. Note: Damage claims cannot be made
during or after installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Dimensions
Tools required
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
WARNING! Before installing a new faucet it is essential that the supply
pipes are thoroughly flushed in order to remove any remaining debris,
solder or other impurities. Failure to carry out this simple procedure
can cause problems or damage to the working of the faucet.
Installing shut-off valves on incoming supply lines is recommended
for ease of maintenance.
Turn off the main water supply before connecting to any existing
pipework or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise,before drilling holes in a wall or floor.
Note:Illustrations not drawn to scale.
3/4"

HANDLE
WASHER
MIXER
BASE RING
C-SHAPED
BLACK
WASHER
FLEXIBLE
PIPES
C-SHAPED
RETAINING
PLATE
NOZZLE
FIXING
NUT
THREADED
STUD
BODY
CARTRIDGE
Replacement part
US-MCARP110
AERATOR
Replacement part
US-AERPROWS
HANDLE
BODY
RETAINING
NUT
COVER
HEXAGONAL
KEY
COVER
CAP
Note:
Generic illustration shown.
Note:
Generic illustration shown.
lShut off the water heating system then, with the main water
supply turned off, open the lowest hot and cold faucets and allow
to drain until the pipes are empty.
lScrew the flexible pipes into the body and fully hand tighten.
Be careful not to overtighten! The hot water should be
connected to the left inlet when the faucet is viewed from the
front.
lPlace the mixer in position to determine if any alteration to the
existing pipework is necessary.
lAfter making any necessary alterations, pass the mixer base ring
and washer over the flexible pipes and threaded stud to form a seal
on the counter/basin top.
lPass the flexible pipes and threaded stud through the hole in the
counter/basin and place the faucet into position.
lSlide the C-shaped black washer and then the C-shaped retaining
plate up the flexible pipes and secure with the fixing nut, finger
tight only.
lCheck that the faucet is positioned correctly and tighten the fixing
nut. The faucet needs to be fixed firmly but do not overtighten as
damage may be caused to the counter/basin.
Copper tails
lIf using copper tails they will need to be gently turned outwards,
then supported approximately halfway down and turned inwards
making the two pipes parallel thus allowing room for couplings. It
is recommended that 1/2” fittings be used to connect mixer to
supply pipes.
ATTENTION:Check all new connections for leaks.
lTurn on the main water supply, close all faucets except the new
mixer and as the system refills, check for leaks.
lOnce satisfied there are no leaks, switch on the heating system.
1Installation
Cleaning the cartridge
lThe concealed cartridge should give trouble-free service
however servicing is a straightforward process.
To remove the cartridge
lWith the water supply turned o, carefully remove the cover cap
and using a hexagonal key loosen the screw but do not remove.
lPull off the handle and unscrew the cover.
lUsing a 7/8” wrench, unscrew and remove the retaining nut.
lPull out the cartridge taking note of its orientation.
lWash the cartridge with clean running water, dry and lightly grease
the seal, (only use silicone grease).
lReplace the cartridge followed by the nut, cover and handle
2 Maintenance

Flow rate (PSI)
Flow rate (GPM)
100
0
0.2
0.4
0.6
0.8
1.0
1.2
20 30 40 50 60 70 80
Flow rate
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
Issue date: 15092019
3 Cleaning Instructions
Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any
overspray. This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the product.
Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup. Follow
instructions to ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or
disinfectants will alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass
cleaners to remain on the surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can cause damage to the finish.
Please see the website for care instructions for specific finishes.