Crosswater Smith Basin 24 Top SMI-BT24-WH User manual

Installation Instructions
Parts supplied
Installation notes
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
Store the basin in a safe place until installation begins to avoid any
damage.
The new basin must be unpacked and inspected before removing the
old fixture.
Assemble the basin on a mat to protect against damage to the basin
surface.
Avoid getting cement, grit, sand or masonry products on to the surface.
Protect and cover the products during the installation period to
prevent damage from occurring.
IMPORTANT: Turn off the main water supply before connecting to
any existing pipe work or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise before drilling holes in a wall or floor.
Dimensions
Introduction
This product has been fully inspected throughout the production
process and only leaves our factory after a 15-step QC process.
Carefully remove the basin from the box and check that all parts have
been supplied.
Before beginning installation of the basin please check for any
damage that may have occurred during transport. Note: Damage
claims cannot be made during or after installation.
Improper installation shall result in loss of warranty in case of damage
caused by impacts or rubbing against rough surfaces.
Prior to installing the basin prepare a connection of water inlet/outlet.
The customer may choose the type and location of the faucets,
installation instructions should be supplied by the faucet manufacturer.
The installation procedure of the basin may differ from that described
in the installation instructions, depending on the installation site.
IMPORTANT: Please read these instructions carefully before
beginning and retain for future reference.
We do not accept responsibility for any problems that may occur
through incorrect installation.
RECOMMENDATIONS:
It is recommended to remove the protective packaging after
installation of the basin.
Smith Basins
24" Top (square)
28” Top (square)
39" Top (Square)
48" Top (Square)
17 1/2"
27 1/2"
4 1/2"
10 3/4"
Ø1 3/4"
9"
2 1/8"
5 1/8"
2"
7 1/4"
Ø1 3/4"
2 1/4"
9"
2 1/8"
5 1/8"
2"
7 1/4"
17 1/2"
23 5/8"
4 1/2"10 3/4"
47 1/4"
9"
2 1/8"
5 1/8"
2"
2 1/4"
9"
2 1/8"
5 1/8"
2"
7 1/4"
7 1/4"
17 1/2"
39 3/8"
4 1/2"2 1/4" 10 3/4"
2 1/4"
17 1/2"
4 1/2"10 3/4"
Ø1 3/4"
Ø1 3/4"
Tools required
Tape
measure
Safety
glasses
Set
square
Pencil Spirit
level
Silicone
sealant
basin waste

Installation
Maintenance
This installation guide does not include details of waste
connection. Final decision about installation of waste connection
should be taken by a suitably qualified contractor.
Install the waste according to the installation instructions supplied
with the waste.
Place the basin in desired position making sure the waste hole is
aligned.
Apply sealant to the inside edge and place into position.
WARNING: Do NOT overtighten the waste as this may cause
long-term damage to the basin.
We recommend using a torque wrench to tighten the waste by
using a torque force between 25Nm or 18.5 ft/lb and 50Nm or
36.8 ft/lb.
IMPORTANT:
Crosswater London cannot accept responsibility for any
injuries caused to those attempting to install this basin
without adequate and appropriate tools or resources.
Remove the basin and waste carefully from the packaging.
 Do not drag the basin over rough surfaces or sharp objects.
Lift and place the basin into position.
Do not drop the basin!
Installation - carriage
Clean the basin regularly with non-abrasive soap and warm water. Fully rinse after cleaning.
While Clearstone is highly stain resistant, it is recommended that water containing additives such as creams, oils or salts is always drained
and rinsed immediately after use.
Please note that hair dyes and color cosmetics (eg. mascara, lipstick, face powder) may leave a slight discoloration if not removed immediately.
If any strong chemicals come into contact with the basin, remove and rinse immediately.
Water temperature should not exceed 49˚C/120˚F.
To remove a fine scratch or a slight mark, use a 1500-grade sandpaper. Gently sand the area with water. For best results, limit sanding to
the smallest possible area around the scratch. Re-polish the surface afterwards using a neutral polishing compound or toothpaste. It may be
possible to polish very fine scratches away without using abrasive papers: scrub gently with a soft brush or plastic pad (not a metal scouring pad)
and a mildly abrasive cream cleaner. Afterwards scrub the whole area with plenty of clean water and re-polish as before.
If the scratch or mark is too deep and cannot be repaired using the above method, it is possible to purchase a repair kit US-CRK. In order
to remove the scratches, follow the instructions included with the kit.
Issue date: 01172023
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact: Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [email protected]
IMPORTANT: Basins are designed for installation with MPRO
vanities.
Basins are not suitable for wall-hung installation without
underside support. It is the responsibility of the installer to
provide adequate support.
Crosswater London cannot be held responsible for inadequate
wall-hung installation.
Mounting hardware for wall-hung installation not supplied.
NOTE: The basins are not come with pre-drilled tap holes,
the semi-punched tap hole is recessed at the back side of
the top hole position.
For information on how to drill tap holes on a basin,
please see Annex A.

Annex A
Issue date: 01172023
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact: Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [email protected]
Tools required
Place the basin upside down on a stand.
Add a layer of protection between the stand and basin
to avoid surface damage or scratching.
Aim the Ø3mm drill bit at pilot hole at the back side
of the basin,then drill through the pilot hole.
Turn over the basin, remove the drill bit from the driller,
and change to suitable hole saw with pilot bit,then aim
the hole saw with pilot bit at the pilot hole just drilled,
and drill through the tap hole.
Ø35mm drill
Ø30mm drill
35mm hole saw with pilot bit
30mm hole saw with pilot bit
Drilling Tap Hole
IMPORTANT:
1. The drill bit must be held at the right angle to the hole to be drilled.
2. Secure the basin, go slow and steady, push it down to drill the tap hole. Any small mistakes can mean that your taps won’t fit onto
the basin correctly.
3. Always inspect you drill bits and hole saws prior to use. If the tip or edge is damaged in any manner, do not use it as it will most likely
cause your material to crack.
3mm Masonry drill bit