Crosswater Leyden 14-05 User manual

15122806
For ease of installation you will need:
To read the installation instructions completely before beginning.
To read all warnings, care, and maintenance information.
Leyden Floor-mount Tub Filler
14-05
Installation Instructions
Before beginning installation, check for any damage that
may have occurred during transport.
Note: Damage claims cannot be made during or after
installation.
Anti-scald protection is the responsibility of the installer
and according to applicable codes.

14-05
Installation Instructions
15122806 2
1 2
43
FRONT
HOT
COLD
FRONT
SEALING TAPE
Adequate floor support is required. The WOOD SUPPORT
must be a minimum of 2" (51mm) thick by 10" (254mm)
wide. 2x6 lumber is NOT adequate for this application.
WOOD SUPPORT must be located with in the MIN. and
MAX. arrows that are marked on the front of the PLASTER
GUARD .
IMPORTANT: Use a ROUND BUBBLE LEVEL to level the
WOOD SUPPORT . The WOOD SUPPORT must be
perfectly level. Secure WOOD SUPPORT to floor joists.
Check for level again.
Locate the position on the wood support where the
MANIFOLD MOUNTING BASE will be installed. Use the
MANIFOLD MOUNTING BASE as a guide to mark the four
mounting hole locations.Drill pilot holes if required.
Secure the MANIFOLD MOUNTING BASE to the WOOD
SUPPORT with SCREWS provided.Verify that the
MANIFOLD MOUNTING BASE is level and then fully
tighten SCREWS .
Finish all Hot and Cold supply connections to the
MANIFOLD MOUNTING BASE .Loosen the two PLASTER
GUARD SCREWS and remove the PLASTER GUARD.
Make sure the two TEST PLUGS are tight, but do not over
tighten.Turn on water supplies and test for leaks.
Turn off water supplies. Replace PLASTER GUARD and
attach with SCREWS.
Sweat together Hot and Cold Supply assemblies. Apply
sealing tape to threaded connections. With the maximum
and minimum measurement in front, the hot supply is to be
installed on the left inlet and the cold on the right as shown
in the image above.
Note: The inlets are marked hot and cold on the bottom of
the MANIFOLD MOUNTING BASE for reference.
HOT
COLD
4
FRONT
MIN 2 11/16 MAX 4 13/16
ROUND BUBBLE LEVEL
MIN 2"
10"-12"
FLOOR JOIST
MIN 10"
FINISHED FLOOR LINE
WOOD SUPPORT
HOT
COLD

14-05-PC
14-05-SN
14-05-PN
14-05-BZ
15122806 6 151228063
Applicable Standards/Codes
Installation Dimensions
IAPMO certified to meet or exceed the following:



4 9/16
3 11/16
3 11/16
5 1/16
4 15/16
MAX 4 13/16
1 5/16
2-1/2-14 NPT
MIN 2 11/16
6
5
8
7
Complete the installation of the Finished Floor. Tile as close
to the PLASTER GUARD as possible.Caulk between
Finished Floor and PLASTER GUARD.
When you are ready to install the TUB FILLER cut the
exposed part of the PLASTER GUARD flush with the
finished floor. Be careful not to damage the floor.
FINISHED FLOOR
8 1/4
11 1/4
10 3/8
8 7/16
1 15/16
38 5/8
35 3/8
30 9/16 32 11/16
24 13/16 26 15/16
32 5/16 34 7/16
1 9/16
5 1/8
4
8 1/8
3 3/8
FINISHED FLOOR
ROUGH FLOOR
Turn off water supplies. With a wrench remove the center
TEST PLUG as shown in Figure A. If the TEST PLUGS
cannot be removed in one piece as shown in Figure A, the
lower half will have to be removed using the supplied 6mm
Hex Wrench as show in Figure B.
Repeat step for the second TEST PLUG.
Remove PLASTIC CAP from bottom of the TUB FILLER.
Before final installation, check that all sealing surfaces are
clean and that the two O-RINGS are installed in the
MOUNTING ADAPTER.Install the MOUNTING ADAPTER
into the MANIFOLD MOUNTING BASE.Install the four
MOUNTING SCREWS and WASHERS through the
MOUNTING PLATE and into the MANIFOLD MOUNTING
BASE. Do not tighten.Rotate the TUB FILLER right or left
to align with Tub.Tighten MOUNTING SCREWS supplied
with 6mm Hex Wrench to secure TUB FILLER.
FIGURE “A” FIGURE “B”
FRONT
6mm HEX WRENCH
6mm HEX WRENCH
FRONT
O-RING SEALS
REMOVE PLASTIC CAP

151228065
9
11
10
12
14-05-PC
14-05-SN
14-05-PN
14-05-BZ
10
Replacement Parts
15122806 4
NO. Description Part No.
1 Hand Shower 5F0M0178
2
Aerator Assembly 5Q0M0025PL
Hand Shower Hose 51014603
3 Diverter Knob Assembly 9Q241700
Hot & Cold Supply 5G0M0237CC
9Q241800
Mounting Assembly 9Q221900NT
5L0P0120Finished Cartridge Dome
9Q241900NT
9Q241500
Hex screw and Key
4
5
7
6
Cartridge Nut
Mounting Base Screw
5T1A0003AL
Cartridge 5D0M0041PL
Hand Shower Outlet 5Y00111000
Diverter Cartridge 5MD0M0006
5T0F0143NT
Escutcheon
8
11
9
10
12 Handle Plug & Screw 9Q1229
13
16
17
14
15
Handle
1
2
3
4
5
15
14
13
12
11
10
9
8
6
16
17
7
Mount handheld bracket onto spout base. Tighten using
supplied hex wrench.
Attach hose to spout and handheld shower.
Once hand shower is attached turn on TUB FILLER and
test the diverter
Turn on water supplies and check all connections for leaks.
Check MANIFOLD connections for leaks.Remove foam
protector and apply sealant to under side edge on
ESCUTCHEON . Slide ESCUTCHEON down to finish floor.
Press into place.Clean up excess sealant.
APPLY SEALANT
FOAM PROTECTOR
Installation is complete.
A
B
6mm hex wrench
6mm hex wrench
5T4000400ZZ0
6mm HEX WRENCH
2.5mm HEX WRENCH
13mm HEX WRENCH
2.5mm HEX WRENCH

151228065
9
11
10
12
10
Replacement Parts
15122806 4
NO. Description Part No.
1 Hand Shower 5F0M0178
2
Aerator Assembly 5Q0M0025PL
Hand Shower Hose 51014603
3 Diverter Knob Assembly 9Q241700
Hot & Cold Supply 5G0M0237CC
9Q241800
Mounting Assembly 9Q221900NT
5L0P0120Finished Cartridge Dome
9Q241900NT
9Q241500
Hex screw and Key
4
5
7
6
Cartridge Nut
Mounting Base Screw
5T1A0003AL
Cartridge 5D0M0041PL
Hand Shower Outlet 5Y00111000
Diverter Cartridge 5MD0M0006
5T0F0143NT
Escutcheon
8
11
9
10
12 Handle Plug & Screw 9Q1229
13
16
17
14
15
Handle
1
2
3
4
5
15
14
13
12
11
10
9
8
6
16
17
7
Mount handheld bracket onto spout base. Tighten using
supplied hex wrench.
Attach hose to spout and handheld shower.
Once hand shower is attached turn on TUB FILLER and
test the diverter
Turn on water supplies and check all connections for leaks.
Check MANIFOLD connections for leaks.Remove foam
protector and apply sealant to under side edge on
ESCUTCHEON . Slide ESCUTCHEON down to finish floor.
Press into place.Clean up excess sealant.
APPLY SEALANT
FOAM PROTECTOR
Installation is complete.
A
B
6mm hex wrench
6mm hex wrench
5T4000400ZZ0
6mm HEX WRENCH
2.5mm HEX WRENCH
13mm HEX WRENCH
2.5mm HEX WRENCH
14-05
Cleaning Instructions
Rinse away any traces of soap and gently dry with a clean,
soft cloth after each use. Rinse completely with water and
dry any overspray. This will maintain the finish and avoid
water spotting.
To remove mineral deposits, use a 50/50 solution of white
vinegar and water. Do not allow the solution to soak on the
product.
Simichrome Polish® contains a protective film to enhance
maintenance and is helpful in preventing water spot
buildup. Follow instructions to ensure optimum results.
Never use an abrasive material such as a brush or scouring
pad to clean the surface. The use of abrasive cleaners,
cleansers or disinfectants will alter the surface finish and
void the warranty.
Do not allow certain materials such as toothpaste, cologne,
shaving cream, nail polish remover, vinegar, wine, drain
and glass cleaners to remain on the surface. Prolonged
contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners
as many can cause damage to the finish.
Please see the website for care instructions for specific
finishes.

15122806 6 151228063
Applicable Standards/Codes
Installation Dimensions
IAPMO certified to meet or exceed the following:



4-1/2"
3-3/4"
3-3/4"
6"
5"
1 5/16
2-1/2-14 NPT
MIN 2-3/4"
MAX 4-3/4"
6
5
8
7
Complete the installation of the Finished Floor. Tile as close
to the PLASTER GUARD as possible.Caulk between
Finished Floor and PLASTER GUARD.
When you are ready to install the TUB FILLER cut the
exposed part of the PLASTER GUARD flush with the
finished floor. Be careful not to damage the floor.
FINISHED FLOOR
8-1/4
11-5/8"
10-3/8
8-1/2"
2"
36-3/4" - 39"
35-3/8
30-1/2"  32-3/4"
24-7/8"  27"
32-1/4" - 34-1/2"
1-1/2"
5-1/8
4
8-1/8
3-3/8
FINISHED FLOOR
ROUGH FLOOR
Turn off water supplies. With a wrench remove the center
TEST PLUG as shown in Figure A. If the TEST PLUGS
cannot be removed in one piece as shown in Figure A, the
lower half will have to be removed using the supplied 6mm
Hex Wrench as show in Figure B.
Repeat step for the second TEST PLUG.
Remove PLASTIC CAP from bottom of the TUB FILLER.
Before final installation, check that all sealing surfaces are
clean and that the two O-RINGS are installed in the
MOUNTING ADAPTER.Install the MOUNTING ADAPTER
into the MANIFOLD MOUNTING BASE.Install the four
MOUNTING SCREWS and WASHERS through the
MOUNTING PLATE and into the MANIFOLD MOUNTING
BASE. Do not tighten.Rotate the TUB FILLER right or left
to align with Tub.Tighten MOUNTING SCREWS supplied
with 6mm Hex Wrench to secure TUB FILLER.
FIGURE “A” FIGURE “B”
FRONT
6mm HEX WRENCH
6mm HEX WRENCH
FRONT
O-RING SEALS
REMOVE PLASTIC CAP
14-05
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [email protected]
Issue date: 20102020
2-15/16"