Crosswater Waldorf US-WF130 User manual

Installation Instructions
3-5/8"
3-1/4"
5-1/2"
1"
1” dia
2-3/4" 2-1/2"
1/2” NPSM
3-5/8"
3-1/4"
5-1/2"
1"
1” dia
2-3/4" 2-1/2"
1/2” NPSM
Adjustable
wrench
Channel
locks
Plumbers’ putty
or caulking
Flat head
screwdriver
Cross head
screwdriver
Hexagonal
key
Waldorf Widespread Basin Faucet
US-WF130
Introduction
Installation notes
The faucets in this range are single flow (hot and cold water mix in the
body) and should therefore be supplied with hot and cold water at
balanced pressures. If the faucets are not supplied at balanced
pressures then the mixer will not function correctly.
The minimum water pressure required for these faucets is 1.45 psi. The
maximum water pressure is 72.5 psi beyond which pressure-reducing
valves must be installed.
The faucets are fitted with quarter-turn ceramic disc cartridges which
provide a good flow rate with very smooth movement.
Before beginning installation , please check for any damage that may
have occurred during transport. Note: Damage claims cannot be
made during or after installation.
IMPORTANT: Please read these instructions carefully before
beginning and retain for future reference. These instructions have
been prepared for your guidance, you must exercise due care at all
times.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Dimensions
Tools required
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
WARNING! Before installing a new faucet it is essential that the supply
pipes are thoroughly flushed in order to remove any remaining debris,
solder or other impurities. Failure to carry out this simple procedure
can cause problems or damage to the working of the faucet.
Installing shut-off valves on incoming supply lines is recommended
for ease of maintenance.
INSTALLATION: Turn off the main water supply before connecting
to any existing pipework or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise,before drilling holes in a wall.

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
Issue date: 15092019
NOTE: For illustration purposes
cross handle shown.
SIDE VALVE
STEEL BRAIDED
HOSES
WASTE
OUTLET
LEVER
INDICE
RETAINING
SCREW
CROSS HANDLE
VALVE COVER
CARTRIDGE
Replacement part
US-BLSP002 - Hot
SEALING
WASHER
LOCK NUT
PLUNGER
CONTROL
ROD
CARTRIDGE
Replacement part
US-BLSP002 - Cold
RUBBER
SEAL
HORSESHOE
PLATE
STUD
RETAINING NUT
lShut off the water heating system. Then, with the main water
supply turned o, open the lowest hot and cold faucets and allow
to drain until supply pipes are empty.
lIdentify all components before fitting.
lUse the rubber seal, horseshoe plate and retaining nut provided
to install the faucet to the basin as shown below.
lConnect the hot and cold water supplies.
ATTENTION:Check all new connections for leaks.
lTurn on the main water supply, close all faucets except for the new
installed faucet and as the system refills, check for leaks.
lOnce satisfied there are no leaks, switch on the heating system.
1Installation
3 Cleaning Instructions
2Parts list
Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any overspray.
This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the product.
Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup. Follow instructions to
ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or disinfectants will
alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass cleaners to remain
on the surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can cause damage to the finish.
Please see the website for care instructions for specific finishes.