Crosswater 11-04 User manual

15122805
Berea Floor-mount Tub Filler
11-04
Installation Instructions
Before beginning installation, check for any damage
that may have occurred during transport.
Note: Damage claims cannot be made during or
after installation.
For ease of installation you will need:
To read the installation instructions completely before beginning.
To read all warnings, care, and maintenance information.
Anti-scald protection is the responsibility of the installer and
according to applicable codes.

11-04
Installation Instructions
15122805 2
12
3 4 5
Adequate floor support is required. The WOOD SUPPORT must be a minimum of
2" (51mm) thick by 10" (254mm) wide. Wood support must be located within
the MIN. and MAX. arrows that are marked on the plaster guard.
Use 4 screws to install and fix the mounting base to the wood support board.
Use level from bottom on both directions to make sure wood support board is flat.
Secure wood support to floor joists.
Assure the valves are centered in
holes that are 3-1/4" to 3-5/8" diameter.
This is required to allow mounting base
to be installed properly.
Turn water supply off. Remove the
plaster guards and the test plugs with
the supplied hex wrench.
Thread and securely tighten 1/2" male
NPT hot and cold supply lines into the
mounting base. Make sure the hot line
is installed on the left side of the
mounting base when facing the
mounting base from the front of where
the floor tub filler will fill the bathtub.
Slide escutcheons onto riser pipe.
Thread hot and cold riser pipes into the
appropriate side of the mounting base
making sure the hot riser is attached to
the hot water supply as noted in the
image above.
FINISHED FLOOR
MIN 2" MAX 3 1/8"
10"-12"
MIN 10"
FLOOR JOIST
MIN 2"
WOOD SUPPORT
FINISHED FLOOR LINE
a
u
s
l
o
t
en -
t
o
le
vel
a
uslot
e
n
-
t
o
l
e
v
el
Hot
Cold
1/2-14 NPT
Mounting base
Hot
Cold
FINISHED FLOOR
3 3/8＂- 3 9/16
FOR HOT SIDE ONLY
FOR HOT SIDE ONLY
5mm HEX WRENCH

Mount valve body on the riser pipe
assembly. Assure the washers are in
place.
Attach hose to spout and handheld
shower. Turn on the water supply to
test the hot, cold and diverter water
flow.
Installation is complete.
Attach handshower yoke to valve
body. Assure the washer is in place.
10
7 86
9 10 11
Replacement Parts
151228053
Before final installation, check that all
sealing surfaces are clean.Install the
mounting adapters onto the mounting
base. Install the mounting screws and
washers through the mounting plate.
And into the mounting base. Do not
tighten. Rotate the tub filler right or left
to align with tub. Tighten mounting
screws to secure tub filler.
Hot
FOR HOT SIDE ONLY
FINISHED FLOOR
FOR HOT SIDE ONLY
To adjust the handshower yoke to
reverse direction, unscrew the nut and
rotate the yoke by 180 degree and
then tighten the nut.
5mm HEX WRENCH
11-04

Installation Instructions
15122805 4
NO. Description Part No.
1
Handshower
5F0M0159010A0
2
Cartridge - Hot 52009335NT
Cartridge - Cold 52009347NT
3
Diverter Handle
Handle Assembly- Hot
9Q240700
9Q240500
Handle Assembly- Cold 9Q240600
5Y00103000
9Q241000NT
9Q241200NT
9Q241100NT
Hex screw and Key
5P00031000
Riser Pipe Assembly- Cold
5y00102000
9Q240800NT
Diverter cartridge
9Q240900
Riser Pipe Assembly- Hot
Handshower Yoke
4
5
6
7
Mounting Base
Escutcheon
5T0F0143NT
Cold Riser Washer
Washer
5R9R0042PL
Aerator Assembly 5Q0M0443PL
5N0C0583NT
Mounting Plate
Mounting plate
Mounting Base
8
11
9
10
12
13
15
14
16
17
18
19
5R4R0128PL
9Q241300NTDiverter Washer Assembly
Handshower Hose
9Q242500
5T4F0006ZZ
20
21
22
19
11
10
1
2
3
4
5
6
7
8
9
13
18
17
20
21
22
12
14
15
16
5mm HEX WRENCH
5mm HEX WRENCH
2.5mm HEX WRENCH
11-04
Cleaning Instructions
Rinse away any traces of soap and gently dry with a clean, soft
cloth after each use. Rinse completely with water and dry any
overspray. This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar
and water. Do not allow the solution to soak on the product.
Simichrome Polish® contains a protective film to enhance
maintenance and is helpful in preventing water spot buildup.
Follow instructions to ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to
clean the surface. The use of abrasive cleaners, cleansers or
disinfectants will alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving
cream, nail polish remover, vinegar, wine, drain and glass cleaners
to remain on the surface. Prolonged contact will alter surface
finishes and void the warranty.
We DO NOT recommend using any household cleaners as
many can cause damage to the finish.
Please see the website for care instructions for specific finishes.

Installation Dimensions
IAPMO certified to meet or exceed the following:



11-1/2"
8-1/2"
7/8
11

34-5/8 - 35-3/4"
43-1/4" - 44-1/2"
2 - 3-1/8
31" - 32-1/4"
5-7/8
4"
7-7/8
9 "
2-1/2-14NPT
5-7/8
1-1/4"
1-1/8
3-1/8
1"
3/4"
Finished Floor
Replacement Parts
15122805
5
11-04
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
Issue date: 20102020