Crosswater Waldorf US-WF135 User manual

Installation Instructions
8-3/4"
5-1/4"
5-1/4"
8-3/4"
5-1/4"
5-1/4"
1/2” NPSM
2-3/8"
3-3/4" 3-3/4"
1-1/8"
1-1/8"
2-3/8"
2-3/8"
2-3/8"
Adjustable
wrench
Channel
locks
Plumbers’ putty
or caulking
Flat head
screwdriver
Cross head
screwdriver
Hexagonal
key
Waldorf Widespread Basin Faucet (Tall Spout)
US-WF135
Introduction
Installation notes
The faucets in this range are single flow (hot and cold water mix in the
body) and should therefore be supplied with hot and cold water at
balanced pressures. If the faucets are not supplied at balanced
pressures then the mixer will not function correctly.
The minimum water pressure required for these faucets is 1.45 psi.
The maximum water pressure is 72.5 psi beyond which pressure-
reducing valves must be installed.
The faucets are fitted with quarter-turn ceramic disc cartridges which
provide a good flow rate with very smooth movement.
Before beginning installation , please check for any damage that may
have occurred during transport. Note: Damage Claims cannot be
made during or after installation.
IMPORTANT: Please read these instructions carefully before you
begin and retain for future reference. These instructions have
been prepared for your guidance, you must exercise due care at
all times.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Dimensions
Tools required
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
WARNING! Before installing a new faucet it is essential that the supply
pipes are thoroughly flushed in order to remove any remaining debris,
solder or other impurities. Failure to carry out this simple procedure
can cause problems or damage to the working of the faucet.
Installing shut-off valves on incoming supply lines is recommended
for ease of maintenance.
Turn off the main water supply before connecting to any existing
pipework or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise,before drilling holes in a wall or floor.

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
Issue date: 15092019
SEALING
WASHER
RUBBER
SEAL
RETAINING
SCREW
INDICE
CROSS HANDLE
VALVE COVER
CARTRIDGE
Replacement part
US-BLSP002 - Hot
COLLAR
O RING
LOCKNUT
CARTRIDGE
Replacement part
US-BLSP002 - Cold
STEEL BRAIDED
HOSES
SIDE VALVE
MIXER
HORSESHOE
PLATE STUD
RETAINING
NUT
LEVER
NOTE: For illustration purposes,
cross handle shown.
lShut off the water heating system then, with the main water
supply turned o, open the lowest hot and cold faucets and allow
to drain until supply pipes are empty.
lIdentify all components before fitting.
lUse the rubber seal, horseshoe plate and retaining nut provided
to install the faucet to the basin as shown below.
lConnect the hot and cold water supplies.
ATTENTION:Check all new connections for leaks.
lTurn on the main water supply, close all faucets except for the new
installed faucet and as the system refills, check for leaks.
lOnce satisfied there are no leaks, switch on the heating system.
Rinse away any traces of soap and gently dry with a clean, soft cloth after
each use. Rinse completely with water and dry any overspray.
This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and
water. Do not allow the solution to soak on the product.
Simichrome Polish® contains a protective film to enhance maintenance
and is helpful in preventing water spot buildup. Follow instructions to
ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to clean
the surface. The use of abrasive cleaners, cleansers or disinfectants will
alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving
cream, nail polish remover, vinegar, wine, drain and glass cleaners to
remain on the surface. Prolonged contact will alter surface finishes and
void the warranty.
We DO NOT recommend using any household cleaners as many can
cause damage to the finish.
Please see the website for care instructions for specific finishes.
3 Cleaning Instructions
1Installation 2Parts list