Crosswater Arcade US-ARC600 User manual

Installation Instructions
Tape
measure
Safety
glasses
Hammer Flat head
screwdriver
1/4” + 5/16”
drill
Pencil Spirit
level
Tools required
Installation notes
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
Store the products in a safe place until you begin installation to avoid
any damage.
Assemble the parts on a mat to protect against scratching the surface.
Avoid getting cement, grit, sand or masonry products on to the
surface.
Protect and cover the products during the installation period to
prevent damage from occurring.
Turn off the main water supply before connecting to any existing
pipework or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise, before drilling holes in a wall or floor.
Introduction
All parts have been fully inspected throughout the production process
and only leave our factory after a 15-step QC process.
Carefully remove the items from the box and check that all parts have
been supplied. Before beginning installation, please check for any
damage that may have occurred during transport. Note: Damage
claims cannot be made during or after installation.
Installation should be completed by at least two suitably competent
installers.
Improper installation shall result in loss of warranty in case of damage.
Wall fixings are not supplied. Source fixings which are suitable to the
site wall.
IMPORTANT: Please read these instructions carefully before you
begin and retain for future reference.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Arcade Pedestal Basin
and Console Sets
US-ARC600 / US-ARC900 / USARC1200
US-ARC1 / US-ARC2 / US-ARC22 / US-ARC23 / US-ARC24
Model options
US-ARC2 legs
with
US-ARC600/ARC900 basin
US-ARC2 legs
with
US-ARC1200 basin
US-ARC22 and US-ARC23
metal console
with
US-ARC600/900 basin
US-ARC24 metal console
with
US-ARC1200 basin
US-ARC1 pedestal
with
US-ARC600/900 basin

Floor nipples
x2
x2x2Legs
x2
Floor nipple washers
x2
1/4”
1Installation - ceramic console legs
Parts supplied - ceramic console legs
2
Temporarily mount the basin onto the 2 legs and locate against the
wall in the desired position. Once in place, mark the footprint of the
leg base onto the oor to conrm the oor xing position.
Note: 2 people are required when
tting a basin onto console legs.
Drill 2 holes (1/4”) in the center of the oor xing positions, then x the
oor nipples onto the oor as shown.
Let the basin sit on the legs and then fix the basin to the wall.
Make sure the basin is level.
Carefully apply silicone on the top of the legs and then locate the legs
over the oor nipples.
4 5
3
The installation process is the same no matter which basin is being installed. US-ARC900 basin is shown for illustration purposes only.

Floor nipples
x2
x2
x2
Floor nipple washers
x2
1/8” Hexagonal key
x1
ARC24
Middle leg
x1
1 Installation - Metal console with glass shelf
Parts supplied
1 2
The installation process is the same no matter which basin is being installed.US-ARC900 basin is shown for illustration purposes only.

Support the glass to avoid damage
while marking the fixing holes.
x8
5/16”
1/4”
1/4”
Apply padding if necessary
Adjust the supports to
make the basin level
Adjust the height of
the legs if necessary
Temporarily place the stand in the desired position. Once in
Tighten the other screws in the
stand if necessary
Install the
basin supports

Installation - pedestal
Installation
Please make sure you have the correct basin suitable for the
pedestal. US-ARC1 suits US-ARC600/900 Basins.
Place the basin in position, against the wall and sitting on top of
the pedestal.

locations on the wall, then proceed to drill.

Please refer to the installation guide that came with the basin.
Issue date: 102019
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
The installation process is the same no matter which basin is being installed. US-ARC600 is shown for illustration purposes only.
Cleaning Instructions
CARE OF VITREOUS CHINA AND FIRECLAY
A simple routine of regular care will keep your vitreous china and fireclay products clean and fresh.
Rinse away any traces of soap and gently dry with a clean soft cloth after each use. A mild detergent, warm water and a soft
cloth will remove normal dirt and soap accumulations from surfaces.
Soft abrasive cleaners may be used on vitreous china and fireclay. Never use abrasive cleaners without water. Do not use
caustic cleaners or disinfectants as they can alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass
cleaners to remain on the surface. Prolonged contact can alter surface finishes and void the warranty.
CARE OF METAL
Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any
overspray. This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the
product.
Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup.
Follow instructions to ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or
disinfectants will alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and
glass cleaners to remain on the surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can cause damage to the finish.