Crosswater Arcade US-ARC15 User manual

Installation Instructions
1-7/8"
1-3/8" 1-3/8"
2-1/2" 1-7/8"
3/4" max
3/4"
7"
2-1/4"
3-1/4"
3/4"
7"
2-1/4"
6-1/4"
3-1/4"
4" 4"
4" 4"
6-1/4"
1-3/8"
17/8” dia
1-3/8"
1-3/8"
2-1/2" 1-7/8"
3/4" max
1-3/8"
Adjustable
wrench
Channel
locks
Plumbers’ putty
or caulking
Flat head
screwdriver
Cross head
screwdriver
Hexagonal
key
Arcade Widespread Basin Faucet
US-ARC15
Introduction
Installation notes
The faucets in this range are single flow (hot and cold water mix in
the body) and should therefore be supplied with hot and cold water
at balanced pressures. If the faucets are not supplied at balanced
pressures then the mixer will not function correctly.
The minimum water pressure required for these faucets is 7.2 psi. The
maximum water pressure is 72 psi, beyond which pressure-reducing
valves must be installed).
The faucets are fitted with quarter-turn ceramic disc cartridges which
provide a good flow rate with very smooth movement.
IMPORTANT: Please read these instructions carefully before you
begin and retain for future reference. These instructions have
been prepared for your guidance, you must exercise due care at
all times.
Before beginning installation, check for any damage that may have
occurred during transport. Note: Damage claims cannot be made
during or after installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Dimensions
Tools required
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
WARNING! Before installing a new faucet, it is essential that the
supply pipes are thoroughly flushed in order to remove any remaining
debris, solder or other impurities. Failure to carry out this simple
procedure can cause problems or damage to the working of the
faucet.
Installing shut-off valves on incoming supply lines is recommended
for ease of maintenance.
Turn off the main water supply before connecting to any existing
pipework or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise,before drilling holes in a wall or floor.

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswater-london.com
email: [e-mail]
Issue date: 15092019
FAUCET
BODY
SPOUT
THREE WAY
CONNECTION
RUBBER
WASHER
BRASS
WASHER
FIXING
NUT
SPANNER
VALVE
BODY
“O” RING
PLASTIC
WASHER
FIXING
WASHER
(METAL)
FIXING
NUT
ROUND
SCREW
FLEXIBLE HOSE
WASHER
(METAL)
NOTE: For illustration
purposes cross handle
shown.
Flow Straightener
Aerator
lShut off the water heating system then, with the main water supply
turned o, open the lowest hot and cold faucets and allow to drain
until supply pipes are empty.
Installing the faucet body
lFit the “O” ring into the groove on the underside of the faucet body.
lInsert the faucet body into the center hole on the basin from above.
lTighten the fixing nut by the supplied spanner and fix the faucet
body on the basin.
lScrew on the three-way connector at the tail of the faucet body.
Installing the hot and cold water valves
lFit the “O” ring into the groove on the underside of both faucet valves.
lInsert the two valve bodies into left and right holes on the counter/
basin.
lTighten the valve with the plastic washers, fixing washers, fixing nuts
and round screws.
lUse two flexible pipes to connect the three-way connector with both
left and right valve bodies.
lConnect the water supply pipe to the tfaucet control valve with the
hot water on the left and the cold water on the right.
ATTENTION:Check all new connections for leaks.
lOnce satised there are no leaks, switch on the heating system.
1Installation
Cleaning the cartridge
lThe concealed cartridge should give trouble free service,
however servicing is a straightforward process.
To remove the cartrudge
lWith the water supply turned o, carefully unscrew the top of the
faucet and then use a suitable adjustable spanner to loosen the nut.
lTake the cartridge out and wash it with clean running water.
lMake sure any trapped debris has been removed.
lDry and lightly grease the seal, (only use silicone grease).
lRefit the cartridge followed by the handle body and lever.
2Maintenance
lThe taps are supplied with factory fitted flow straightener filters
for low-pressure water systems. If the water pressure is high (above
14.5 psi ), replace the flow straightener filter with the high pressure
Neoperl aerator filter (supplied in the box).
lUse the Neoperl key supplied to unscrew the flow straightener
from the nozzle. Replace with the aerator filter. If the supplied
Neoperl key is misplaced, use the top of the spare filter to unscrew
the filter from the nozzle.
lTighten the screw back up.
Before use
lUnscrew the lter and allow the
water to run freely for 5 minutes.
Screw the lter back into the nozzle
once all impurities have been
ushed from the water supply.
Periodically
lUnscrew the lter from the nozzle
and rinse with clean running
water. Once all loose debris and
dirt has been cleared replace the
lter into the nozzle and tighten.
3Filter nozzle maintenance 4 Cleaning Instructions
Rinse away any traces of soap and gently dry with a clean, soft cloth
after each use. Rinse completely with water and dry any overspray.
This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar
and water. Do not allow the solution to soak on the product.
Simichrome Polish® contains a protective film to enhance
maintenance and is helpful in preventing water spot buildup. Follow
instructions to ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to
clean the surface. The use of abrasive cleaners, cleansers or
disinfectants will alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving
cream, nail polish remover, vinegar, wine, drain and glass cleaners to
remain on the surface. Prolonged contact will alter surface finishes
and void the warranty.
We DO NOT recommend using any household cleaners as many
can cause damage to the finish.
Please see the website for care instructions for specific finishes.