CRU Dataport DE100 Series User manual

DE100 Ultra320 68-pin
Removable SCSI Wide Ultra320 Drive Enclosure
Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
DataPort
™
Drive Installation Assembly
Receiving Frame Motherboard
Remote Unit ID Selection: Pins 1-8 of this connector are provided
for remote unit SCSI ID selection through the computer system. Remote
ID selection requires that the unit ID switch located on the inside of the
receiving frame be set to “0” (onboard ID selection is set with a switch
located on the inside of the receiving frame as shown in Figure 4).
Remote Activity LED: Pins 9 & 10 provide power to a remote LED
device activity indicator.
Enable Termination Power Connector (W2): A jumper is installed
at the factory and enables termination power to/from the SCSI bus.
NOTE: Do NOT remove this jumper!
Figure 2: Receiving Frame Motherboard (rear view)
Typical 2MM Drive ID Pin Confi guration
Figure 3 illustrates a typical SCSI ID select connection to a drive with
2mm ID select pins. The wires on the wire harness connect to the
positive pin (or signal pins) on the disk drive. In some cases, the drive
manufacturer will label the signal pins as Pin 1, 3, 5, 7, (instead of 0,
1, 2, 3 as shown in fi gure below). Also, in some cases, the even-num-
bered Pins 2, 4, 6 are used for Ground.
Attach the ID select cable to the drive using the 2mm connectors. Align
the “ID0” pin with the black wire. Attach the 1.25mm connector on the
other end of the ID select cable to the 1.25mm connector (J3B) provided
on the signal distribution board, located inside the carrier. Refer to the
manufacturer’s documentation to disable termination on the drive.
NOTES: For SCSI Ultra320 operation, the Ultra320 DE100 requires Ultra320
drives, Ultra320 HBA, and Ultra320-compliant cabling (internal and external).
Ultra320 DE100 can support Ultra320 implementations with a maximum of fi fteen
(15) Ultra320 drives (Ultra320 repeater may be required).
Ultra320 DE100 receiving frames are indicated by their BLUE LED, while the
Ultra320 DE100 carriers are indicated by the Ultra320 logo.
Figure 1: Drive Installation Assembly
Receiving
Frame
Cable Cover
(provided)
Disk Drive
(not included)
Power Cable
I/O Cable
ID Select Cable
Drive
Carrier
#6-32 Phillips
Flat Hd. Screw
(6 Total)
DC Power
Connector (P1)
W2 Jumper (factory
installed - do not remove)
Option Pin
Connector
(W1)
Pins 11-22
Reserved
Remote ID
Select {
Ultra320
DE100
I/O Connector
(J3)
(P1)
+5 GND 12
ID0
ID1
ID2
ID3

Product Warranty
CRU-DataPort (CRU) warrants the Data Express DE100 to be free of
significant defects in material and workmanship for a period of five
years from the original date of purchase. CRU’s warranty is nontrans-
ferable and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other warran-
ties. CRU expressly disclaims all other warranties, including but not
limited to, the implied warranties of merchantability and fitness for a
particular purpose and non-infringement of third-party rights with re-
spect to the documentation and hardware. No CRU dealer, agent or
employee is authorized to make any modification, extension, or addi-
tion to this warranty. In no event will CRU or its suppliers be liable for
any costs of procurement of substitute products or services, lost profits,
loss of information or data, computer malfunction, or any other spe-
cial, indirect, consequential, or incidental damages arising in any way
out of the sale of, use of, or inability to use any CRU product or ser-
vice, even if CRU has been advised of the possibility of such damages.
In no case shall CRU’s liability exceed the actual money paid for the
products at issue. CRU reserves the right to make modifications and
additions to this product without notice or taking on additional liability.
Certification
EMI Standard: FCC Part 15 Class B, CE
EMC Standard: EN55022, EN55024
FCC Certification
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received;
including interference that may cause undesired operation.
Register your product at www.CRU-DataPort.com and be
automatically entered to win a free prize!
A7-100-0004 Rev. 1.0
Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
DataPort
™
Selecting the Unit ID Number: Use the alignment tool (provided)
to select the ID number of the disk drive.
NOTE: The lock on the Data Express receiving frame functions
as a lock and a DC power switch for the carrier unit. The lock
MUST be engaged (turned counterclockwise) in order to supply
power to the carrier and installed drive unit.
Figure 3: Typical SCSI ID Select Connections ( 2mm drive pins)
Drive Carrier
ID Select
Switch
Drive Carrier
Guide
Receiving
Frame
Unit ID
Number
Display
Lock and
DC Power
Switch Front of Unit
Drive Carrier
(removed)
Figure 4: Unit ID Select Switch Location