CRU Dataport RJR400 User manual

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
RJR400
Removable 4-Bay SATA 3Gb/s Drive Enclosure
Front Panel
Carrier Eject: Push to eject carrier from the receiving frame (Figure 3).
Safety Lock: The safety lock assures proper seating of the drive
carrier within the receiving frame and prevents accidental ejection of
carrier. To lock, turn button 90° clockwise until horizontal. To unlock,
turn button 90° counterclockwise until vertical.
Power Switch (HD1 - HD4): Each drive carrier has its own power switch.
Drive Activity LED (HD1 - HD4): Each power switch acts as a Power
and Drive Activity LED.
NOTE: Drive Activity LED features supported by RJR400 Rev. C00
and up (rev. level can be found on P/N label located on the unit).
Steady GREEN glow indicates power ON.
Flashing AMBER indicates drive activity.
Fan LED: GREEN indicates normal fan operation. RED indicates fan
failure.
Overtemp LED/Reset: Flashing RED indicates overtemperature
conditions (default is 60° C) and a audible alarm will sound. Pushing
this switch will reset Overtemp LED back to Green, as well as turn off
audible alarm.
Figure 2: Rear Panel
REAR PANEL
DC Power Connectors: Standard 4-pin DC Power Connector to
accept DC power.
NOTE: If using DC power, both DC power connectors
must be provided with power for proper operation.
SATA Power Connectors: Alternative 15-pin SATA Power Connector
to accept DC power.
NOTE: If using SATA power, both power connectors
must be provided with power for proper operation.
I/O Connectors: The input/output connector provides a standard
interface for all SATA signals.
Temperature Setting (JP1): Jumper set to 60oC overtemperature
(default).
Reserved (JP3): Factory-reserved.
Fan Speed: High (recommended) and low speed. Jumper is set to
High (default).
NOTE: Fan speed feature supported by RJR400 Rev. C00
and up (rev. level can be found on P/N label located on
the unit).
Cooling Fan: Fan provides enhanced heat dissipation (53.9 CFM).
Figure 1: Front Panel
Carrier
Eject
Power Switch
& Power/Drive
Activity LED
OverTemp LED
& Reset
Carrier HandleSafety
Lock
Fan LED
Temperature Setting (JP1)
DC Power Connectors Cooling Fan
I/O
Connectors
Reserved
(JP3)
SATA
Power
Connectors
Fan Speed

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
Product Warranty
CRU-DataPort (CRU) warrants the Data Express RJR400 to be free
of significant defects in material and workmanship for a period of
five years from the original date of purchase. CRU’s warranty is
nontransferable and is limited to the original purchaser.
Limitation of Liability
The warranties set forth in this agreement replace all other war-
ranties. CRU expressly disclaims all other warranties, including but
not limited to, the implied warranties of merchantability and fit-
ness for a particular purpose and non-infringement of third-party
rights with respect to the documentation and hardware. No CRU
dealer, agent or employee is authorized to make any modifica-
tion, extension, or addition to this warranty. In no event will CRU
or its suppliers be liable for any costs of procurement of substi-
tute products or services, lost profits, loss of information or data,
computer malfunction, or any other special, indirect, consequen-
tial, or incidental damages arising in any way out of the sale of,
use of, or inability to use any CRU product or service, even if CRU
has been advised of the possibility of such damages. In no case
shall CRU’s liability exceed the actual money paid for the products
at issue. CRU reserves the right to make modifications and addi-
tions to this product without notice or taking on additional liability.
Certification
EMI Standard: FCC Part 15 Class B, CE
EMC Standard: EN55022, EN55024
FCC Certification
This device has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. Operation is subject to the following two condi-
tions:
1. This device may not cause harmful interference.
2. This device must accept any interference received;
including interference that may cause undesired operation.
Register your product at www.CRU-DataPort.com
Rev. 1.1
Installation
NOTE: A #2 Phillips screwdriver will be required.
1. Eject carrier from the receiving frame (Figure 3).
2. Carefully insert drive (not included) into the carrier. Turn
the drive/carrier assembly over.
3. Bottom-mount the drive into the carrier with four (4)
Phillips screws (Figure 4).
Push to Eject
Carrier
Insert SATA Drive
(not included)
Bottom-Mount
Drive
Figure 4: Installing a Drive into the Carrier
Figure 3: Ejecting the Carrier