CTC Union TSB6000 Series User manual

TSB6000 Series Modular Switch BoxTSB6000 Series Modular Switch Box
4 Channel4 Channel
Product ManualProduct Manual

2
• Introduction...................................................................3
• Product Description...........................................................3
• Product Dimensions & Diagram................................................4
• Mounting Instructions .........................................................5
• Conduit Entry .................................................................6
• Grounding ....................................................................7
• Installation of Sensor/Signal Input Cable.......................................8
• Post Installation Testing ..................................................... 11
• Warranty & Return Information .............................................. 13
T  C

3
I
CTC modular switch box solutions allow for the monitoring of remotely mounted
vibration sensors, which would otherwise be restricted to human access due to
safety considerations.
TSB6000 Series Modular Switch Box Overview: 4 switched triaxial sensor input
module for a total of 12 channels, stainless steel slope top enclosure
CTC modular switch box solutions allow for the monitoring of remotely mounted
vibration sensors, which would otherwise be restricted to human access due to
safety considerations.
The TSB6000 Series 4 Switched Triaxial Channel stainless steel modular switch
box is used to convert the four-conductor input wiring of up to 4 remotely installed
triaxial accelerometers to switched BNCs and a switched four-pin connector for
data collection. Input wiring from each sensor is connected to the outputs via
quick-connect or screw terminal blocks. Each terminal block includes inputs for
signal/power on each axis, common and shield.
Additional switch box modules can be installed or removed after initial
manufacturing and onsite installation, using the quick-release DIN rail clip. Each
new module features a detachable plug for easy cable installation. If continuous
output is desired, select the TSB6001 Series. On all continuous output modules,
a quick disconnect T-plug is supplied to easily connect and disconnect the input
wiring.
Rated for NEMA 4X (IP66), the TSB6000/TSB6001 Series can withstand harsh
environments including temperatures ranging from -58 to 180 °F (-50 to 82 °C).
The box is also resistant to hose directed fluid and corrosion. A locking latch is
installed on the door allowing the box to be sealed from the elements when not
in use.

4
P D
Measurement
Location Card
Four-pin MIL
Output Connector
Switch
BNC Output
Connectors
Figure 1. Dimensions
Figure 2. Diagram
Front View Side View

5
M I
Note: if you have purchased a modular switch box without cable entries provided,
you should add your own entry prior to mounting the modular switch box. CTC
does not recommend drilling holes in the top of the enclosure due to access and
moisture concerns.
Mounting
Holes
0.31 in./7.95 mm
Figure 3. Modular Switch Box Rear View

6
C E
If you are running conduit to your enclosure, ensure the conduit cable entry
enters from the bottom of the enclosure when mounted.
Note: To ensure moisture will not flow into the enclosure, a hole should be drilled
at the lowest point in the conduit to provide drainage for any moisture.
Figure 4. Conduit Entry for Modular Switch Box
Correct
Drill Drain
Hole Here

7
G
Ensure the shield ground wire on the TSB6000 Series modular switch box is
grounded to earth ground.
A. Mounting to Earth Ground
When mounting TSB6000 Series modular switch boxes to earth ground (such
as an I-Beam), no additional steps are necessary, as the enclosure is grounded
internally.
Figure 5. Modular Switch Box (TSB6000) Earth Ground

8
B. Mounting to non-grounded structure
When mounting the modular switch box to a non-grounded structure, ensure the
shield ground wire or customer supplied ground wire is tied to a source of earth
ground.
Figure 6. Ground Wire Placement
S I
Installation of sensors/signal input cable
1. Feed blunt end through the cable entry at the bottom of the enclosure.
Note: it is recommended that cables are marked on both ends.
For cord grip cable entry, take off the cord grip cover with bushing and run cable
into enclosure, hand tighten cord grip cover to base to prevent damage of cord
grip.

9
1. Strip outer jacket of cable back 1¼ in. and remove all of the shielding.
2. Separate the internal wires from the shield.
3. Strip red and black insulation back ¼ in.
Figure 8. Bottom View
Figure 7. Front View
4. Locate the appropriate plug (identified by channel number), remove it, and
install the wires using a small flathead screwdriver. Push plug back into location.
Orientation is as follows:
a. Green insulated conductor wire is connected to Channel X.
b. Red insulated conductor wire is connected to Channel Y.
c. White insulated conductor wire is connected to Channel Z.
d. Black insulated conductor wire is connected to (-).
e. Shield drain wire is connected to ground (GND).
Figure 9. Stripped Wire
(-) Common
Shield / Drain wire
(+) Channel Y
(+) Channel X
(+) Channel Z

10
5. Insert plug into the appropriate PC board connector and double check to ensure
that the cable is going to the correct channel.
6. Mark the Measurement Location Card located on the inside front cover with a
description of each measurement location.
Figure 11. Connecting Cables to Modular Switch Box (TSB2001)
Figure 10. Connecting Cables to Modular Switch Box (TSB2000)
X
Y
Z
-
GND
SENSOR #1
SENSOR #2
SENSOR #3
SENSOR #4
X
Y
Z
-
GND
X
Y
Z
-
GND
X
Y
Z
-
GND
Sensor Inputs
Green = Signal/Power X Axis
Red = Signal/Power Y Axis
White = Signal/Power Z Axis
Black = Common
Grey = Shield (Ground)
Sensor Outputs
Green = Signal/Power X Axis
Red = Signal/Power Y Axis
White = Signal/Power Z Axis
Black = Common
X
Y
Z
-
GND
SENSOR #1
SENSOR #2
SENSOR #3
SENSOR #4
X
Y
Z
-
GND
X
Y
Z
-
GND
X
Y
Z
-
GND
Sensor Inputs
Green = Signal/Power X Axis
Red = Signal/Power Y Axis
White = Signal/Power Z Axis
Black = Common
Grey = Shield (Ground)
Sensor Outputs
Green = Signal/Power X Axis
Red = Signal/Power Y Axis
White = Signal/Power Z Axis
Black = Common
X
Y
Z
-
GND
SENSOR #1
SENSOR #2
SENSOR #3
SENSOR #4
X
Y
Z
-
GND
X
Y
Z
-
GND
X
Y
Z
-
GND
Sensor Inputs
Green = Signal/Power X Axis
Red = Signal/Power Y Axis
White = Signal/Power Z Axis
Black = Common
Grey = Shield (Ground)
X
Y
Z
-
GND
SENSOR #1
SENSOR #2
SENSOR #3
SENSOR #4
X
Y
Z
-
GND
X
Y
Z
-
GND
X
Y
Z
-
GND
Sensor Inputs
Green = Signal/Power X Axis
Red = Signal/Power Y Axis
White = Signal/Power Z Axis
Black = Common
Grey = Shield (Ground)
Sensor Outputs
Green = Signal/Power X Axis
Red = Signal/Power Y Axis
White = Signal/Power Z Axis
Black = Common
X
Y
Z
-
GND
SENSOR #1
SENSOR #2
SENSOR #3
SENSOR #4
X
Y
Z
-
GND
X
Y
Z
-
GND
X
Y
Z
-
GND
Sensor Inputs
Green = Signal/Power X Axis
Red = Signal/Power Y Axis
White = Signal/Power Z Axis
Black = Common
Grey = Shield (Ground)
InputsInputs
Inputs Inputs