CTC Union IFS-803GSM-8PH24 User manual

Installation
The switch comes with both wall mount and DIN rail hardware
brackets. When installing the DIN rail bracket, be sure to correctly
align the orientation pin.
Figure 8. DIN Rail Figure 9. Wall Mount
The switch with DIN Rail bracket has a steel spring in the upper
rail of the bracket. This spring is compressed for mounting and
un-mounting by applying downward force.
Figure 10. Mounting Figure 11.Un-mounting
Introduction
IFS-803GSM-8PH(E)24 are managed industrial grade Fast
Ethernet PoE (Power over Ethernet) switches that provide stable
and reliable Ethernet transmission. Housed in rugged DIN rail or
wall mountable enclosures, these switches are designed for harsh
environments, such as industrial networking and intelligent
transportation systems (ITS) and are also suitable for many
military and utility market applications where environmental
conditions exceed commercial product specifications. Standard
operating temperature range models (-10°C to 60°C) and wide
operating temperature range models (-40°C to 75°C) fulfill the
special needs of industrial automation applications.
Features
Redundant dual DC inputs 24/48VDC
DCV 'boost' feature; regulated 55VDC PoE output voltage
IP30 rugged metal housing
Wide temperature range -40°C ~75°C (IFS-803GSM-8PHE24)
Supports many advanced Ethernet L2 functions
Console, Telnet (ssh), Web and SNMP management
Industrial grade EMS, EMI, UL60950-1, EN50121-4,
EN61000-6-2, EN61000-6-4
Specifications
Ethernet Interface
Standards: IEEE802.3 (10Base-T), 802.3u (100Base-TX)
RJ-45 (shielded) Ports: 8 ports
Speed: 10/100M
Optical Interface
Standards: IEEE802.3u (100Base-FX), 802.3z (1000Base-X),
802.3ab (1000Base-T)
3 ports, SFP based
Speed: 100/1000M (Manual)
Switch Features
Store & Forward Switch
Supports IEEE802.3x Flow Control
Auto MDI/MDI-X
Duplex: Full/Half (Auto-negotiation per IEEE802.3u)
Switching Fabric: 7.6Gbps (Non-blocking)
Packet Buffer: 1Mb
MAC Table: 8K
MTU: 64~9600 bytes
Quick Installation Guide
IFS-803GSM-8PH24
IFS-803GSM-8PHE24
Industrial Grade Managed Fast Ethernet PoE Switches
Specifications (cont.)
Power over Ethernet
8 PoE enabled ports, Alternate A Mode
Supports IEEE802.3af 15.4watts PoE per port
Supports IEEE802.3at 30watts PoE+ per port (180W budget)
Positive (VCC+) pins 1,2 (55VDC); Negative (VCC-) pins 3,6
Power
Absolute Input Range: 20VDC~57VDC
Reverse Polarity Protection: Yes
Dual Power Inputs: Yes
Connector: Removable terminal block
Consumption:
Items
Input Voltage
Total Power
Consumption
Device Power
Consumption
PoE Budget
Boost
Efficiency
24VDC
198.3W
7.3W
180W
94%
48VDC
193.2W
7.9W
180W
97%
Mechanical
Water & Dust Proof: IP30 Protection
Dimensions: 116 mm (D) x 64 mm (W) x 152 mm (H)
Mounting: DIN-Rail, Wall Mount (Kits included)
Weight: 970 g
Environmental
Operating Temperature : -10°C~60°C (IFS-803GSM-8PH24)
-40°C~75°C (IFS-803GSM-8PHE24)
Storage Temperature: -40°C~85°C
Humidity: 5%~95% (Non-condensing)
Certifications
EMC: CE
EMI (Electromagnetic Interference): FCC, FCC Part 15 Subpart
B Class A, CE EN55022 Class A
Railway Traffic: EN50121-4
Immunity for Heavy Industrial Environment: EN61000-6-2
Emission for Heavy Industrial Environment: EN61000-6-4
EMS (Electromagnetic Susceptibility) Protection Level:
EN61000-4-2 (ESD) Level 3, Criteria B
EN61000-4-3 (RS) Level 3, Criteria A
EN61000-4-4 (Burst) Level 3, Criteria A
EN61000-4-5 (Surge) Level 3, Criteria B
EN61000-4-6 (CS) Level 3, Criteria A
EN61000-4-8 (PFMF, Magnetic Field) Field Strength:
300A/m, Criteria A
Safety: UL60950-1 ●Shock: EN60068-2-27
Freefall: EN60068-2-32 ●Vibration: EN60068-2-6
MTBF: 314,064 hours (MIL-HDBK-217)
[email protected]
V1.0
- 1 -
- 2 -
To download this QIG or a more complete user manual, please visit
http://www.ctcu.com/Industrial/
T+886-2-26591021
F+886-2-26590237
E[email protected]
CTC Union Technologies Co., Ltd.
Far Eastern Vienna Technology Center
(Neihu Technology Park)
8F, No. 60 Zhouzi St., Neihu District, Taipei 114
Taiwan
© 2014 CTC Union Technologies Co., Ltd.
All trademarks are the property of their respective owners.
Technical information in this document is subject to change without notice.
- 7 -
www.ctcu.com

Connectors
Figure 1. Front Panel
LAN and Fiber Connection
IFS-803GSM-8PH(E)24 PoE switches have 8 electrical LAN ports
(labeled 1~8) and 3 fiber ports (SFP based, labeled Fiber 1~3) on
the front panel. The LAN ports that utilize shielded RJ-45
connectors support 10/100M; while the fiber SFP ports support
100/1000M.
PoE Ports
All 8 LAN ports support PoE (Power over Ethernet) per
IEEE802.3af (15.4W) or IEEE802.3at (30W) for connection to
standard PoE PD (Power Devices) such as IP Cameras, Access
Points, IP Phones, Digital Signage, etc. PoE eliminates the need to
run separate power to these devices thereby simplifying
deployment and reducing expenses.
The LAN ports may also connect to any non-PoE device for
normal Ethernet transmission without any damage to the non-
PoE device or to this device.
RJ-45 Ethernet Port Pinouts
Figure 2. RJ-45 Ethernet Port Pinouts
Power and Alarm
Figure 5. Terminal Block
A removable terminal block on the top panel provides both
power and alarm connections. Power can be provided through
the dual inputs from separate sources. The alarm relay contact
can be wired into an alarm circuit which senses an alarm
condition when the contact is broken. The alarm relay is normally
closed when there is no alarm condition. The alarm conditions are
user programmable through management to include power, link
faults or other fault conditions. Please note that the alarm relay
contact can only support 1A current at 24VDC. Do not apply
voltage and current that exceed these specifications.
CLI & Web Basic Operation
IFS-803GSM-8PH(E)24 are managed Fast Ethernet PoE switch
devices. Initial configuration (assignment of IP address) may be
accomplished via the RS-232 console and a PC or laptop running
terminal emulation software. Configure the terminal as follows:
115200 speed, 8 data bits, no parity, 1 stop bit, no flow control
IFS-803GSM-8PH(E)24 PoE switches use a command line
interface (CLI) through the serial port. Once the IP address has
been configured, a web browser can be used to configure the
device through a more easy to use GUI (graphical user interface).
Please refer to the operation manual on the CDROM.
Using the provided console cable, connect the RJ-45 to the
"CONSOLE" port and the DB9 to PC COM port. Apply power to the
switch. At the "Username:" prompt, enter 'admin' (lower case, no
quotes). Just press Enter when prompted for password.
To set the IP address and subnet mask issue this command:
> ip address 1 192.168.0.250/24
(example: sets VID 1 to 192.168.0.250, subnet 255.255.255.0)
NOTE: The factory default IP address is 10.1.1.1 with mask
255.255.255.0
RJ-45 Ethernet & PoE Pin Assignments
Pin
No.
RJ-45
Ethernet
100Base-TX
PoE
Output
1
RX+
V+
2
RX-
V+
3
TX+
V-
4
-
5
-
6
TX-
V-
7
-
8
-
CONSOLE Port
The RJ-45 port labeled “CONSOLE”is an RS-232 terminal port
for local management. These models use a “light”CLI (Command
Line Interface) in addition to a user friendly Web interface and
industry standard SNMP. See page 5 for basic CLI and Web
operation.
One RJ-45 to DB-9 cable is provided with this device. CONSOLE
port pinouts (Figure 2) and RS-232 DB-9 (Figure 3) connector are
illustrated below together with RJ-45 to DB-9 signal mapping
information. Use the supplied cable to connect the RJ-45
CONSOLE port to a console PC.
Figure 3. CONSOLE Port Pinout
RJ-45 to DB-9 Signal Mapping
DB-9 (Female)
Direction
RJ-45
Signal
Pin
Pin
Signal
RXD
2
3
TXD
TXD
3
6
RXD
GND
5
5
GND
LED Indicators
LED
Color
Definition
PWR1/
PWR2
Green
Power is connected and active at the
PWR1/PWR2 input terminal connection.
Off
PWR1/PWR2 is not connected.
Fault
Amber
When one or more of the programmable
alarm conditions is active.
Off
Normal operation without faults.
Alarm conditions are all disabled.
CPU ACT
Green
Lit during normal use, indicating a healthy
condition of the running CPU.
Ring
Master
Yellow
Lit when this unit is the 'master' in a ring
and all units are configured for u-Ring or
ERPS.
LAN
LINK/ACT
Green
The connected LAN speed is 10/100M.
Blinking
Blinking when there is Ethernet traffic.
Off
No Ethernet link.
FIBER
LINK/ACT
Green
The fiber link is up.
Blinking
Blinking when there is data traffic.
Off
No fiber link.
PoE
Green
The respective LAN port has successfully
negotiated PoE and is supplying output
power to the remote connected PD.
Blinking
One of the PoE faults (overload, short
circuit, port failure at startup) occurs.
Off
PD is not connected or output power is not
provided.
Application
- 3 -
- 4 -
- 5 -
- 6 -
Figure 7. u-Ring Topology and Application
Fault
Figure 6. Alarm Relay Circuit
Normally Closed (NC)
www.ctcu.com
Figure 4. RS-232 (Female) Pinout