CYBEX ATON User manual

ATON
Rear Facing Infant Car Seat / Base
Owner’s Manual
Manual del Propietario
4—32 lb
1,8—14,5 kg
One inch or more
Una pulgada o más
Maximum 30”
Máximo 76 cm
++
READ this Owner’s
Manual carefully before
rst use,and keep it for
future reference.
LEA este Manual
del Propietario
minuciosamente antes
de usarlo y guarde para
su futura referencia.
English Español

Dear parents,
Thank you for purchasing the CYBEX Aton.We are proud to bring this German engineered product to
North America.We hope the Aton will make your child’s travel both safer and more pleasant,as well
as make installation and use for you as simple and easy as possible.
The Aton has undergone extensive testing and meets or exceeds all applicable Federal Motor Vehicle
Safety Standards in North America.
Statistics show that over 72% of car seats are being used incorrectly! Please read and follow these
instructions to install the Aton correctly,even if the installation and use of this infant car seat might
seem simple and intuitive.
YOUR CHILD’S SAFETY DEPENDS ON YOU FOLLOWING THESE STEPS:
1.Choosing the best location in your vehicle for the child restraint.
2.Correct adjustment and use of the ve-point Harness.
3.Proper use of LATCH or the vehicle seat belts to install this child restraint.
4.Proper recline angle of the child restraint.
Before the rst use of the Aton infant car seat,please make sure you have followed all the steps in
the Safety Checklist and CYBEX Safe Practices found on page 40.
We recommend keeping your child rear facing in a properly installed Aton infant seat until he/she
outgrows the maximum weight or height for the seat. For many children,that will be when they are
two years of age or more.Please consider the environment and recycle if possible when you
dispose of this product and its packaging.
No car seat can guarantee protection from injury in every situation,but proper use helps reduce the
risk of death or serious injury. If you have any questions or need assistance,please contact Regal
Lager,Inc.,the North American distributor at 1–800–593–5522.Also,please remember to register
your infant car seat so we can contact you in the unlikely event of a recall.
Keep this Owner’s Manual for future reference by storing it in the pocket on the bottom of the Aton.
We appreciate your purchase and invite you to visit www.cybex-online.com to see other great CYBEX
products.
Bengt Lager
President,Regal Lager,Inc.
CPS Technician
Welcome to CYBEX!

Registration and Recall Information .................................................................................................2
Certication ..................................................................................................................................2
Warnings and Important Safety Information......................................................................................3
Overview of the Aton Base...............................................................................................................6
Features of the Aton Base................................................................................................................7
Super Easy AndTight™ Installation................................................................................................7
Recline Angle Adjustment ..............................................................................................................7
Level Indicator...............................................................................................................................7
Steel Chassis ................................................................................................................................7
Overview of the Infant Carrier ..........................................................................................................8
Features of the Infant Carrier...........................................................................................................10
Harness Buckle .............................................................................................................................10
Chest Clip.....................................................................................................................................10
One Handed Harness Adjustment...................................................................................................10
Carry Handle.................................................................................................................................11
Designer Canopy™.......................................................................................................................11
Using the Infant Carrier...................................................................................................................12
Child Size Requirements................................................................................................................12
Adjusting the Harness Height.........................................................................................................13
Securing Child in Infant Carrier ......................................................................................................14
Newborn Inlay...............................................................................................................................16
Infant Insert ..................................................................................................................................16
More Support Options ...................................................................................................................17
Vehicle Seat Location Requirements ................................................................................................18
Vehicle Seat Belts .........................................................................................................................19
Lower Anchors and Tethers for CHildren (LATCH)..............................................................................20
LATCH Guides................................................................................................................................21
Installing the Base..........................................................................................................................22
Using LATCH..................................................................................................................................22
Using Vehicle Lap and Shoulder Belt..............................................................................................24
Using Vehicle Lap Belt Only............................................................................................................26
Using Infant Carrier with the Base....................................................................................................28
Storing the LATCH Connectors .........................................................................................................29
Installing the Infant Carrier without the Base ....................................................................................30
Using Vehicle Lap and Shoulder Belt..............................................................................................30
Using Vehicle Lap and Shoulder Belt (Alternate Method).................................................................32
Using Vehicle Lap Belt Only............................................................................................................34
Installing the Infant Carrier in Aircraft...............................................................................................35
Adjusting the Recline Angle.............................................................................................................36
When using the Base ....................................................................................................................36
When using Infant Carrier without Base..........................................................................................37
Care and Cleaning..........................................................................................................................38
Safety Checklist..............................................................................................................................40
Resources ......................................................................................................................................41
If You Need Help............................................................................................................................41
Warranty ........................................................................................................................................42
Table of Contents
English

Please complete the Registration Card that came
with your Child Restraint and mail it immediately or
register online.
Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a
recall.Send your name,address,e-mail address if
available, and the restraint’s model number and
manufacturing date to:
CYBEX Registration
1100 Cobb Place Blvd.NW
Kennesaw,GA 30144 USA
or call 1-800–593–5522
or register online at:
www.regallager.com/register/cybexcarseats
For recall information, call the U.S. Government’s
Vehicle Safety Hot line at:1–888–327–4236 (TTY:
1-800-424-9153), or visit www.NHTSA.gov.
Certication
This child restraint system conforms to all applicable Federal Motor Vehicle
Safety Standards.
THIS RESTRAINT IS CERTIFIED FOR USE IN MOTOR VEHICLES AND AIRCRAFT.
2
FOR YOUR CHILD’S CONTINUED SAFETY
Please take a few moments to promptly  ll out and return the
attached card (or register online using the direct link to the
manufacturer’s registration website provided below).
Although child restraint systems undergo testing and evalua-
tion, it is possible that a child restraint could be recalled.
In case of a recall, we can reach you only if we have your name
and address, so please send in the card (or register online) to
be on our recall list.
Please  ll this card out and mail it NOW,
or register online at
www.regallager.com/register/cybexcarseats
while you are thinking about it.
The card is already addressed and we’ve paid the postage.
Tear off and mail this part
CONSUMER: JUST FILL IN YOUR NAME, ADDRESS AND E-MAIL
ADDRESS. PLEASE PRINT CLEARLY.
Your Name
Your Street Address
City State Zip Code
Email Address
CHILD RESTRAINT REGISTRATION CARD
Registration information
may be found on the
label to the right or
afxed to the underside
of the Infant Carrier and
the Base.
MODEL NAME:
MODEL NUMBER:
COLOR:
MANUFACTURED IN:
DO NOT USE AFTER:
ATON
12-4000012
P. POTION FABRIC: COMFORT
12/2010
12/2016
Registration and Recall Information

• READ this Owner’s Manual carefully before rst use,and keep it for future reference.
• NEVER install or use this child restraint until you have read and understand the instructions in this
manual AND in your vehicle Owner’s Manual .If there is a conict between the two, the vehicle
Owner’s Manual must be followed.FAILURE TO FOLLOW these instructions can result in DEATH or
SERIOUS INJURY of your child in a sharp turn,sudden stop or crash.
• DO NOT ALLOWothers to install or use this child restraint unless they understand how to correctly
install and use it.
• ONLY PLACE this child restraint REAR FACING in a vehicle seating location allowed by the vehicle
manufacturer.Refer to your vehicle's Owner’s Manual for information about vehicle seat belt
systems, air bags,and child restraint installation,to determine allowable seating positions.
• Not every location within a vehicle may be safe for the installation of this child restraint.In fact,
some vehicles have no seating position that is safe for the installation of an Infant Car Seat.
IMPROPER PLACEMENT of this child restraint within a vehicle will increase the risk of death or
serious injury.
• Based on crash statistics,the National Highway Trafc Safety Administration (NHTSA) recommends
that parents select the REAR SEAT as the safest location for a properly installed child restraint
rather than a front seating position.
• The primary protection for occupants of a vehicle in a collision is the structure of the vehicle itself;
a child restraint will not protect a child when the vehicle is seriously impacted.CORRECTLY USED,
this child restraint will substantially improve the chances for survival in most crashes.
When Used Inside a Vehicle
• ONLY USE with children who weigh between 4 and 32 lb (1,8 and 14,5 kg) AND whose height is
30 inches (76 cm) or less.
• DO NOT USE this child restraint if the top of your child's head is LESS THAN 1 inch (2,5 cm) from
the top of the restraint.
• ALWAYS CHECK the Harness buckle to make sure it is securely latched.
• ALWAYS KEEP your child properly secured in the Harness.A snug strap should not allow any slack.
It lies in a relatively straight line without sagging.It does not press on the child’s esh or push the
child’s body into an unnatural position.
• NEVER leave your child unattended or alone in the vehicle even for one minute.
• NEVER place this child restraint on a front seat with an active airbag.DEATH or
SERIOUS INJURY may occur.The REAR seat is the safest place for children 12
and under.
3
WARNING
DEATH or SERIOUS INJURY can occur
Important Safety Information
English

• ONLY USE this child restraint REAR FACING.
• NEVER INSTALL this child restraint in vehicle seats that face the rear or side of the vehicle.
• NEVER USE this child restraint in a vehicle seating position where it cannot be secured tightly.A
loosely installed child restraint will NOT PROTECT your child in a crash.
• NEVER LEAVE a vehicle seat with a folding mechanism unlocked. In the event of a sudden stop,
a loose vehicle seat back could prevent this child restraint from protecting your child as well as
it should.
• NEVER USE this child restraint with any motorized,or door mounted vehicle seat belts.Your child
would not be properly restrained in the event of a crash.
• NEVER USE this child restraint on boats,low speed vehicles (LSV),all-terrain vehicles (ATV), golf
carts,or any other non-certied application.
• BEFORE each use,ALWAYS CHECK that the child restraint is tightly secured in the vehicle seat
and does not move more than 1 inch (2,5 cm) in any direction when checked at the belt path.
• ALWAYS CHECK buckles and other parts for hot surfaces.A hot surface could burn your child!
Cover an unoccupied child restraint with a blanket when leaving it in a vehicle exposed to
sunlight.
• ALWAYS CHECK to make sure the Infant Carrier is securely attached to the Base,each time you
use this restraint.After attaching the Infant Carrier to the base,LIFT UP on the Infant Carrier
handle to make sure that it is securely attached to the base.
• NEVER LEAVE an empty child restraint unsecured in your vehicle.This restraint MUST ALWAYS BE
SECURED,even when not occupied.An unsecured child restraint could injure vehicle occupants
in a sudden stop or crash.
• If the LATCH connectors are NOT BEING USED make sure they are securely stored.
• DO NOT USE this child restraint if it has been in a crash.There may be hidden damage and it
must be replaced.Your insurance company may provide some assistance in replacing the child
restraint.
• NEVER USE this child restraint when it is older than six (6) years.The date of manufacture can be
found on a label afxed to the bottom of the Infant Carrier as well as the Base.
• NEVER USE this child restraint if any of the Harness or LATCH straps are cut,frayed or damaged
in any way.
• NEVER USE accessories or parts with this child restraint,other than those approved by CYBEX.
Use of accessories or parts from other manufacturers could alter the performance of the child
restraint.
4
WARNING
DEATH or SERIOUS INJURY can occur

When Used Outside a Vehicle
• NEVER LEAVE child unattended even for a short time.Your child can tip or move the Infant Carrier
by their movements,kicking or grabbing on to their surroundings.
• SUFFOCATION HAZARD: NEVER place Infant Carrier on beds,sofas or other soft surfaces.The
Infant Carrier can roll over on soft surfaces and suffocate child.
• STRANGULATION HAZARD: NEVER leave child in Infant Carrier when the Harness straps are loose
or undone.A child can strangle in loose Harness straps.
• ALWAYS USE the complete and buckled ve-point Harness around your child.
• FALL HAZARD: NEVER place Infant Carrier on counter tops,tables, or other elevated surfaces.A
child’s movements can slide the Infant Carrier,and child and carrier may fall.
• NEVER place Infant Carrier on top of a shopping cart.
• MAKE SURE the handle is LOCKED in the Carry Position before lifting Infant Carrier by the handle.
An unlocked handle could move unexpectedly,causing child to fall.
• ONLY USE Infant Carrier with strollers that are approved by the manufacturer.Refer to the stroller
Owner's Manual for details about how to attach the Infant Carrier to your stroller.
Additional Safety Information
• REGISTER this child restraint.This is the only way to reach you in the event of a recall.
• DO NOT use this or any other child restraint with a premature,low birth weight,or medically
fragile infant,until after you have consulted with your doctor.Some infants may have difculty
breathing or have other medical problems when placed in a seated position.
• DO NOT ALLOWchildren to play with this child restraint.
• DO NOT ATTEMPT to make repairs to or otherwise modify or tamper with this child restraint.
• DO NOT USE a child restraint whose history you do not know.
• DO NOT ALLOWchildren to play with vehicle seat belts.They may create an ENTANGLEMENT
HAZARD for any child that can reach the seat belt and may wrap it around his or her neck.
• DO NOT LEAVE loose objects (e.g.groceries,books,bags) in a vehicle. In the event of a sudden
stop, loose objects will keep moving, potentially causing serious injuries.
• NEVER TEND to your child’s needs while driving.ALWAYS safely stop your vehicle in order to tend
to your child.
• NEVER TAKE your child out of the infant car seat while the vehicle is moving.Unrestrained
occupants are at a greatly increased risk of DEATH or SERIOUS INJURY in a car crash.
• ALWAYS LOCK an unoccupied vehicle.Children can get into vehicle and accidentally lock
themselves in,resulting in DEATH or SERIOUS INJURY by hyperthermia. 5
WARNING
DEATH or SERIOUS INJURY can occur
English

6
Belt Guide
Locking Lever
Infant Carrier Attachment Lock
Infant Carrier
Attachment Catch
Infant Carrier Release
LATCH Strap Adjuster
Green Button
Belt Tensioning Plate
Steel Chassis
LATCH Strap
Tensioning Loop
Leveling Foot
Leveling Foot
(fully extended)
LATCH Connector Storage
Level Adjustment Handle
Level Indicator
LATCH Guides
LATCH Connector
Overview of the Aton Base

22–32 lb
10–14,5 kg
4–22 lb
1,8–10 kg
22–32 lb
10–14,5 kg
4–22 lb
1,8–10 kg
22–32 lb
10–14,5 kg 4–22 lb
1,8–10 kg
22–32 lb
10–14,5 kg
4–22 lb
1,8–10 kg
OR
7
Super Easy And Tight™ Installation
The Aton Belt Tensioner uses CYBEX's Super Easy And
Tight (SEAT) Technology to achieve a quick and secure
installation every time,whether you choose to use LATCH
or vehicle belts.
Simply open the Belt Tensioning plate by turning the
Locking Lever to the OPEN position and lifting up
on the Plate. Route the belts under the Plate, or connect
LATCH Connectors,remove slack and close the Plate
to tighten.
Recline Angle Adjustment
The Recline Angle may be easily adjusted by squeezing
the Level Adjustment Handle while positioning the Base.
Release handle to lock foot in place.The Leveling Foot
has four positions.
Level Indicator
The Level Indicator is calibrated for different weight
ranges. Use the weight range appropriate for your child.
Steel Chassis
A continuous metal frame front to back provides strength
and allows a secure attachment between Infant Carrier
and Base.
Leveling Foot
(fully extended)
Features of the Aton Base
English

Top View
8
Harness Buckle
Harness Straps
Harness Adjustment Strap
Adjuster Strap Cover
Harness
Adjustment Button
Buckle Pad
Chest Clip
Designer Canopy (Stored)
Infant Insert
Shoulder Pads
Belt Guide
Carry Handle
Adjustment
Button
Travel System
Release Button
Overview of the Infant Carrier

Bottom View
9
Harness Slots
Shoulder Belt Guide
Splitter Plate
Harness
Harness Adjustment Strap
Base Attachment Rod
Owner's Manual
Storage
Base Attachment Rod
Clear Plastic Cover
Overview of the Infant Carrier
English

10
Harness Buckle
To release Buckle Tongues,rmly press the RED button on
the Harness Buckle.
To fasten, insert each Tongue into Buckle, listening for an
audible CLICK.Pull on each to verify a secure connection.
Check that the Buckle functions properly and is kept
free of dirt and debris. For cleaning,see page 39.
Chest Clip
To separate Chest Clip, squeeze top and bottom tabs and
pull apart.To fasten, slide the two parts together until an
audible CLICK is heard.
Always position the center of the Chest Clip even with
the child's armpits.
One Handed Harness Adjustment
1. Loosen Harness by rmly pressing down
the Harness Adjustment Button (a) while
pulling forward on both straps (b).
2. Pull the Adjuster Strap to tighten the Shoulder Straps.
a
b
Features of the Infant Carrier

11
Carry Handle
The Carry Handle has 3 locked positions:
A.Carry
B. Storage
C. Resting
To move handle to a new position,squeeze both Handle
Adjustment Buttons and rotate.
ALWAYS use the CARRY POSITION while using this
child restraint in a vehicle.
MAKE SURE THE handle is LOCKED in the CARRY
POSITION before lifting Infant Carrier by the handle.
An unlocked handle could move unexpectedly,
causing child to fall out.
NEVER hang toys or other objects from handle
when using child restraint in a vehicle as they could
seriously injure a child in a sudden stop or crash.
Designer Canopy™
Simply pull forward to extend the Aton Canopy.The
Canopy has two positions.
To retract the Canopy,gently push it back into its original
position.
A
B
C
1
2
Features of the Infant Carrier
English

Child Size Requirements
ONLY USE this child restraint with children who meet ALL of
the following requirements:
• Weight is between 4—32 lb (1,8—14,5 kg) AND
• Height is a maximum of 30 inches (76 cm) AND
• Top of the head is at least 1 inch (2,5 cm) below the
top of the Infant Carrier.
DO NOT USE this child restraint if your child does not
meet ALL of these requirements.
Rear Facing is Safest
We recommend that all children ride rear-facing until they are at least two (2) years of age. It is
safer for young children to ride rear-facing as long as possible to protect the head, spine and upper
torso in the event of a collision.
Use the CYBEX Aton until your child reaches the maximum weight or height limits.Because not
all children have the same shapes and sizes,DO NOT USE the Aton when the top of the child's
head is less than 1 inch (2,5 cm) from the top of the Infant Carrier.This allows for proper
protection during a crash.
After your child outgrows the Aton,keep your child rear-facing in a convertible seat as long as
possible,according to the manufacturer's specications, before turning them around to ride
forward facing.
12
1 inch (2,5 cm)
Using the Infant Carrier

Adjusting the Harness Height
For proper use of the Infant Carrier, the Harness shoulder
straps MUST be at the correct height for your child.
1. Place child in Infant Carrier making sure their bottom
is in the seat,and their back is fully supported.
2. Identify the CLOSEST Harness Strap Slots that
are AT or BELOWyour child's shoulders.
3. Remove child and turn Infant Carrier over
to locate the Splitter Plate. Unhook one
Shoulder Strap from the Splitter Plate.
Only adjust one strap at a time to have the other
strap for reference.
4. From the front, pull the strap out of the slot,
Seat Cover,and Infant Insert (if used).
5. Re-thread through the Infant Insert (if used),
Seat Cover and correct Harness Slot.
6. Reattach strap to the Splitter Plate
and repeat for the other strap.
7. Check that Harness is free from twists and that
it can be tightened and loosened easily.
NEVER remove Harness or Harness components from
Infant Carrier.
DO NOT USE child restraint if any part of the Harness
is damaged.
Periodically check for proper shoulder strap height as
your child grows.
13
Using the Infant Carrier
English

Securing Child in Infant Carrier
1. Loosen Harness by rmly pressing down
the Harness Adjustment Button (a) while
pulling forward on both straps (b).
2. Press RED button on Harness
Buckle to release Tongues.
3. Separate Chest Clip and spread straps
apart.Place child in Infant Carrier in seated
position making sure their bottom is in the
seat,and their back is fully supported.
4. Pull Harness straps over each arm onto shoulders
and around the hips. Make sure Buckle Pad
and Harness Buckle are between the legs.
Newborns tend to draw arms and legs close to their
bodies.Gently extend each limb to allow for proper
Harness positioning.Be mindful of especially
sensitive areas (e.g.bellybuttons,circumcisions).
5. Buckle by inserting one Tongue at a time into the
Harness Buckle listening for an audible CLICK with
each one.Make sure Harness Straps are not twisted.
MAKE SURE Harness straps are AT or BELOWchild's
shoulders.If not,see Adjusting Harness Height,page
13 or the Infant Insert section on page 16.
ALWAYS CHECK Harness Buckle to make sure it is
securely latched.Failure to fasten and tighten the
Harness system correctly with each use can result in
DEATH or SERIOUS INJURY.
6. Connect the Chest Clip listening for an audible CLICK.
14
a
b
Using the Infant Carrier

7. Pull up on Harness Straps to snug around the child's
hips while holding the Harness Buckle in place.
8. Slowly pull the adjuster strap to tighten the Shoulder
Straps.A snug strap should not allow any slack. It lies
in a relatively straight line without sagging.It does
not press on the child’s esh or push the child’s body
into an unnatural position.
9. Position the center of the Chest Clip even with the
child's armpits.Make sure the Shoulder Pads do
not interfere with the placement of the Chest Clip.
If necessary, tuck the top edge of the Shoulder Pads
through the Cover and Harness Slots to provide
more space for the Chest Clip.
Harness Pinch Test.To test for a properly tightened
Harness,pinch the shoulder strap.A snug Harness
should not allow you to pinch any slack when
pinched between your thumb and forenger.
ALWAYS KEEP child properly secured in Harness.
NEVER secure child in Infant Carrier dressed in a
bulky garment or heavy clothing,
To keep child warm,place a blanket over child and
Infant Carrier,AFTER you have properly secured and
tightened Harness around your child.
15
Using the Infant Carrier
English

Newborn Inlay
The Newborn Inlay is a specially designed EPS foam
component located in the bottom of the Infant Carrier
underneath the Seat Cover.The Inlay helps to position
smaller babies properly in the Aton during their rst few
months.We recommend using the Newborn Inlay until
your child is 11 lb (5 kg) (about 3 months old).
Removing the Newborn Inlay
At the bottom of the seat there is an opening in the seat
cover.Simply lift up and remove the Newborn Inlay from
the seat.Keep it for future use.
Infant Insert
To ensure a better t for infants,we recommend using the
Aton Infant Insert.The Insert will give more stability to the
head and upper torso,as well as provide a better Harness
t for smaller babies.We recommend using the Infant
Insert until 22 lb (10 kg) or until child needs more room.
Folding the Insert
If you child's shoulders are below the rst set of Harness
Slots,you may fold the lower portion of the Infant Insert
UNDER to boost the child up for proper Harness t.Unfold
the Insert when the child's shoulders are at the height of
the second set of Harness Slots.
Removing the Infant Insert
Follow the steps for Adjusting Harness Height on page 13.
NEVER place extra padding under or behind the
child.The Infant Insert is the only approved padding
to be used with the Aton.
16
Using the Infant Carrier

More Support Options
Head and Upper Body
If you feel your child needs further head or upper body
support,you may use tightly rolled blankets positioned
along your child's sides for added support.
Only add blankets after child is secured in the seat,
making sure that nothing interferes with the Harness.
DO NOT loop the rolled blanket over the child's head.
The loop may slip behind the child's head and force
it forward,disrupting proper breathing or putting the
head and neck in an awkward position that will
increase the risk of DEATH or SERIOUS INJURY in a
crash.
Between the Legs
With smaller babies,there is often a gap between the
crotch and the crotch strap. If your child slides forward
in the crotch strap,resulting in a slouched posture, you
may use a rolled wash cloth for support.Position a tightly
rolled wash cloth between the legs and behind the
Harness Buckle and Pad to "ll in" the extra space.
Only add the rolled wash cloth after child is in the Infant
Carrier with their bottom in the seat,and their back fully
supported.Make sure legs are straddling the crotch strap.
NEVER place extra padding UNDER or BEHIND the
child.The Infant Insert is the only approved padding
to be used with the Aton.
17
Using the Infant Carrier
English

The REAR SEAT is the safest location for a properly
installed child restraint.
Use this child restraint in FORWARD FACING VEHICLE
SEATS ONLY.
The rear seat is the safest location for an Infant Car Seat.In addition,have an adult ride in the rear
with the child in order to monitor the child.
The best position for the child restraint is one that is recommended by your vehicle Owner’s
Manual and results in a proper and secure installation of the restraint.
18
WARNING DEATH or SERIOUS INJURY can occur
NEVER place this child restraint on a front seat with an active airbag.
DEATH or SERIOUS INJURY may occur.The REAR seat is the safest place
for children 12 and under.
Based on crash statistics,the National Highway Trafc Safety
Administration (NHTSA) recommends that parents select the REAR SEAT
as the safest location for a properly installed child restraint rather than a
front seating position.
ONLY PLACE this child restraint REAR FACING in a vehicle seating location allowed by the
vehicle manufacturer.Refer to your vehicle Owner’s Manual for information about vehicle
seat belt systems, air bags,and child restraint installation to determine allowable seating
positions.
Vehicle Seat Location Requirements