D-CUT MH-330 User manual

OPERATION MANUAL
D-Cut Multi-Flooring Cutter MH-330
www.dcutproducts.com

2
SAFETY RULES FOR THE MULTI-FLOORING CUTTER
1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE
OPERATING THE D-CUT MULTI-FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of D-Cut Multi-flooring
Cutter, obtain advice from a qualified instructor or call 800-982-3434 USA
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or
medication.
4. Always wear safety approved eye protection with side shields(ANSI Z87.1)
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the D-Cut Multi-flooring
Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or solid stand.
8. Use the right tool. Do not force the D-Cut Multi-flooring Cutter or use it for a
job for which it was not designed; use only on approved materials.
9. Keep the blade sharp. A dull blade will not perform properly.
10. Always keep hands away from blade while operating or carrying the cutter.
11. Do not alter or misuse this tool. The D-Cut Multi-flooring Cutter is precision
built; modifications not specified in this manual may result in a dangerous
and unsafe environment.
12. Maintain the D-Cut Multi-flooring Cutter with care. Keep Blade sharp and
clean. Follow instructions for changing accessories.
13. Use only recommended accessories. The use of improper accessories may be
hazardous and cause injuries.
14. Never leave the D-Cut Multi-flooring Cutter unattended. Secure the handle
with the lock chain when not in use.

3
SET UP
CUTTING AND C
Installation of the Cutter (2)
Pull up the lock pin on the
aluminum handle as shown and
insert the handle into the
handle base as shown.
Warning: Do not put your
fingers against the sharp edge
of the blade at any time.
Installation of the Cutter (1)
Install the table to the cutter
base with the provided screws
and bolts as shown.
Warning: Do not put your
fingers against the sharp edge
of the blade at any time.
Cutting Preparation
Adjust the angle attachment to
desired angle as needed.
The angle attachment can be used
on left side of the table as shown.
Warning: Do not put your fingers
against the sharp edge of the
blade at any time.

4
CUTTING
Straight Cutting
Insert material between the
cutting blade and the base,
flush with the angle attachment
as shown and hold the material
with foot then push handle
down to complete a cut.
Warning: Maintain control of
the handle. Do not allow
handle to slam back after
making a cut.
45° Cutting
Adjust the angle attachment to
45°. Insert material between
the cutting blade and the base,
against the angle attachment as
shown, then push the handle
down to complete a cut.
Warning: Maintain control of
the handle. Do not allow
handle to slam back after
making a cut.
Warning: Do not put your
fingers against the sharp edge
of the blade at any time.

5
Carry
Hook the chain to the ring on
the handle and carry the
cutter as shown.
Changing the Blade
Use the provided Allan wrench
to remove the five screws, then
hold the blade by each end and
carefully remove the blade out of
the blade holder.
Note: The flat side of the blade
faces the table.
Warning: Do not put your
fingers against the sharp edge of
the blade at any time.
MAINTENANCE

6
PART LIST

7
Parts Q’ty Parts Q’ty
1 Side Frame A 1 29 Hex head Screw M5 × 8 9
2 Customized Bolt M8 2 30 Hex Head Screw M8 × 8 4
3 Spring Washer Φ8 2 31 Hook-2 1
4 Hex Head Bolt M8 × 66 4 32 Carrying Handle 1
5 Nylon Board 2 33 End Table Frame 1
6 Nylon Bar Holder 1 34 Thin Nut M5 3
7 Hex Head Screw M12 × 30 1 35 Blind Rivet Φ54
8 Nylon Bar 1 36 Rubber Feet-1 2
9 Hex Head Screw M6 × 12 5 37 Cross Bar 3
10 Hex Head Screw M5 × 16 4 38 Working Table Frame 2
11 Aluminum Eccentric Cam 1 39 Cross Head Screw M5 × 10 2
12 Hex Head Screw M5 × 10 1 40 Plain Washer Φ5 2
13 Side Frame B 1 41 Rubber Feet-2 2
14 Rotating Shaft A 1 42 Guide Rod 2
15 Handle Base 1 43 Spring 2
16 Pull Pin 2 44 Blade Holder 1
17 Handle-1 1 45 Rotating Shaft B 1
18 Handle-2 1 46 Blade 1
19 Right ABS Handle 1 47 Blade Cutting Base 1
20 Thin Nut M4 2 48 Cross Head Screw M6 × 16 2
21 Hook A 1 49 Knurled Pin M5 1
22 Left ABS Handle 1 50 Nylon Lock Nut M5 5
23 Cross Head Screw M4 × 31 2 51 Nut Curve Locating Slot 1
24 Chain 1 52 Nut Base 1
25 Cutting Guide 1 53 Hex Nut M5 2
26 Hex Head Screw M5 × 20 6 54 Allan Wrench M5 1
27 Hex Head Screw M5 × 12 8 55 Allan Wrench M6 1
28 Working Table 1 56 Allan Wrench M8 1
PART LIST

8
MH-230/ MH-330 Cutting Capacity Chart
WOOD FLOORING Janka Rate
MH-230 MH-330
Limit on
Engineered
Wood Flooring
Limit on
Engineered
Wood Flooring
Eastern White Pine
380 Yes Yes
Basswood
410 Yes Yes
White Pine
420 Yes Yes
Hemlock
500 Yes Yes
Chestnut 540 Yes Yes
Larch
590 Yes Yes
Douglas Fir 660 Yes Yes
Southern Yellow Pine (Loblolly and Shortleaf)
690 Yes Yes
Shedua
710 Yes Yes
Sycamore
770 Yes Yes
Parana
780 Yes Yes
Lacewood / Leopardwood 840 Yes Yes
Southern Yellow Pine (Longleaf)
870 Yes Yes
Cedar
900 Yes Yes
Paper Birch
910 Yes Yes
Boire
940 Yes Yes
Black Cherry / Imbuia 950 Yes Yes
Sakura 995 Yes Yes
Teak
1000 Yes Yes
Black Walnut
1010 Yes Yes
Boreal
1023 Yes Yes
Makore
1100 Yes Yes
Brazilian Eucalyptus / Rose Gum 1125 Yes Yes
Cocobolo
1136 Yes Yes
Carbonized Bamboo (represents one species) 1180 Yes Yes
Heart Pine 1225 No Yes
Movingui
1230 No Yes
Yellow Birch
1260 No Yes
Carribean Heart Pine
1280 No Yes
Red Oak (Northern)
1290 No Yes
American Beech
1300 No Yes
Ash (White)
1320 No No
Ribbon Gum
1349 No No
Tasmanian Oak
1350 No No
White Oak
1360 No No
Australian Cypress
1375 No No
Natural Bamboo (represents one species)
1380 No No
Coffee Bean 1390 No No
Hard Maple / Sugar Maple 1450 No No
Sweet Birch
1470 No No

9
Curupixa
1490 No No
Sapele / Sapelli 1510 No No
Kambala
1540 No No
Peroba
1557 No No
True Pine / Timborana 1570 No No
Zebrawood
1575 No No
Tualang
1624 No No
Wenge / Red Pine 1630 No No
Highland Beech
1686 No No
Locust
1700 No No
Kempas
1710 No No
Merbau
1712 No No
Blackwood 1720 No No
African Padauk
1725 No No
Rosewood
1780 No No
Bangkirai
1798 No No
Afzelia / Doussie 1810 No No
Hickory / Pecan / Satinwood 1820 No No
Goncalo Alves / Tigerwood 1850 No No
Purpleheart 1860 No No
Jarrah 1910 No No
Amendoim
1912 No No
Merbau
1925 No No
Tallowwood
1933 No No
Cameron
1940 No No
Bubinga
1980 No No
Sydney Blue Gum 2023 No No
Karri
2030 No No
Brushbox
2135 No No
Pradoo
2170 No No
Santos Mahogany / Bocote / Cabreuva 2200 No No
Mesquite 2345 No No
Brazilian Cherry / Jatoba 2350 No No
Spotted Gum
2473 No No
Red Mahogany / Turpentine 2697 No No
Bloodwood
2900 No No
Angelim Pedra
3040 No No
Brazilian Redwood / Paraju 3190 No No
Ebony
3220 No No
Cumaru / Brazilian Teak 3540 No No
Ipe / Brazilian Walnut / Lapacho 3684 No No