D-CUT LH-320 User manual

OPERATION MANUAL
Vinyl Plank Flooring Cutter
LH-320
www.dcutproducts.com

2
SAFETY RULES FOR THE FLOORING CUTTER
1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE
OPERATING THE D-Cut MULTI-FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of D-CUT LVT-flooring
Cutter, obtain advice from a qualified instructor.
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or
medication.
4. Always wear safety approved eye protection with side shields(ANSI Z87.1)
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the D-CUT LVT-flooring
Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or a solid stand.
8. Use right tools. Do not force the D-CUT LVT -flooring Cutter or use it for a job
for which it was not designed; use only on approved materials.
9. Always keep hands away from blade while operating or carrying the cutter.
10. Do not alter or misuse this tool. The D-CUT LVT-flooring Cutter is precision
built; modifications not specified in this manual may result in a dangerous
and unsafe environment.
11. Maintain the D-CUT LVT-flooring cutter with care. Follow instructions for
changing accessories.
12. Use only recommended accessories. The use of improper accessories may be
hazardous and cause injuries.
13. Never leave the D-CUT LVT-flooring Cutter unattended. Secure the handle
with the lock chain when not in use.

3
CUTTING AND C
Installation of the Cutter
Assemble the handle set to the cutter
base with provided screws as shown.
Warning: Do not put your fingers
against the sharp edge of the blade at
any time.
45° Cut
Position the guide bar at 45°. Insert the
floor plank between the cutting blade
and the base, along with the guide bar
as shown, then pull the handle down to
complete a cut.
Note:
Some of 45° cuts may need two cuts: a
straight cut first and then the angle cut.
Straight Cut
Insert the floor plank between the
cutting blade and the base, flush with
the guide bar on the working table and
hold the plank then pull handle down
to complete a cut.
Warning: Maintain control of the
handle. Do not allow handle to slam
back after making a cut.

4
Lengthwise Cut
Insert the floor plank between the
cutting blade and the working table
along with the guide bar from the
side way. The guide bar may be
locked on both sides of the working
table. Keep moving the plank along
with the guide bar after each cut
until the plank is completely cut.
Notch Cut
Make a lengthwise cut first to
desired length on the floor plank as
mentioned above, then turn the
plank 90°, and put desired cutting
point right under the blade.
Unlock two screws on the blade
holder and pull out the blade as
shown to above mentioned desired
cutting point, then pull the handle
down to complete a cut.
Changing the Blade (2)
First loosen the two screws on the
blade holder as shown illustration 1.
Then pull out the blade to the right
side as shown illustration 2.
Use included Allan wrench to
remove the three screws.
Note: The flat side of the blade
should face the working table.
Warning: Do not put your fingers
against the sharp edge of the blade
at any time.

5
Transport
Insert the lock pins to lock the
cutting head when the cutter is not
in use, to keep the blade in a close
position for the safety as shown on
upper illustration.
Pull out the carry handle to carry
the cutter as shown.
Changing the Nylon Bar
Use included Allan wrench to take off
four screws as shown, and remove the
nylon bar.
Warning: Do not put your fingers
against the sharp edge of the blade at
any time.
Changing the Blade (2)
Pull out the blade to the left side as
shown and remove the two screws,
then carefully move the blade out
of the small blade holder.
Note: The flat side of the blade
should face the working table.
Warning: Do not put your fingers
against the sharp edge of the blade
at any time.

6
Explosive View

7
Parts Q’ty
Parts Q’ty
1 Cutter Base 1 30 Handle 1
2 Spring 2 31 Nut 2
3 Washer 5 2 32 Right ABS Handle 1
4 Locker Nut M5 2 33 Screw M4X30 2
5 Screw M4X14 5 34 Pin 1
6 Spring Washer 5 4 35 Left ABS Handle 1
7 Screw M5X10 8 36 Guide Bar 1
8 Nylon Bar Holder 1 37 Screw M5X25 6
9 Side Cover 2 38 Screw M5X16 6
10 Screw M5X16h 2 39 Working Table 1
11 Right Rotating Shaft 1 40 Cross Bar A 1
12 Spring Washer 6 11 41 Cross Bar B 2
13 Pan head Screw M6X10 8 42 Left Working Table Base 1
14 Cylindrical Screw M6X10 4 43 Screw M6X20 2
15 Spring Base 4 44 Right Working Table Base 1
16 Screw M6 2 45 Removable Guide Bar A 2
17 Nylon Bar 1 46 Removable Guide Bar b 2
18 Nylon Piece 4 47 Puller 2
19 Stopper 1 48 Blade Holder 1
20 Handle Base 1 49 Screw M8X20 4
21 Screw M6X12 2 50 Rubber Feet 8
22 Blade Holder Base 1 51 Locker Nut M8 4
23 Washer 6 1 52 Screw M4X10 2
24 Aluminum Wheel 2 53 Left Rotating Shaft 1
25 Screw M6X20 3 54 Stopper A 4
26 Nylon Wheel 2 55 Locker Nut M10 2
27 Tube Plug 2 56 Blade 1
28 Aluminum Eccentric Cam 1 57 Wheel 2
29 Battery Box and Light Belt Assembly 1 58 Screw M5X10 5
Explosive View