D-CUT LT-200 User manual

OPERATION MANUAL
PVC Flooring Cutter LT-200
www.dcutproducts.com
CUTTING AND C

2
SAFETY RULES FOR THE FLOORING CUTTER
1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE
OPERATING THE D-Cut MULTI-FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of D-Cut Multi-flooring
Cutter, obtain advice from a qualified instructor or call 800-982-3434 USA
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or
medication.
4. Always wear safety approved eye protection with side shields(ANSI Z87.1)
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the D-Cut Multi-flooring
Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or solid stand.
8. Use the right tool. Do not force the D-Cut Multi-flooring Cutter or use it for a
job for which it was not designed; use only on approved materials.
9. Keep the blade sharp. A dull blade will not perform properly.
10. Always keep hands away from blade while operating or carrying the cutter.
11. Do not alter or misuse this tool. The D-Cut Multi-flooring Cutter is precision
built; modifications not specified in this manual may result in a dangerous
and unsafe environment.
12. Maintain the D-Cut Multi-flooring Cutter with care. Keep Blade sharp and
clean. Follow instructions for changing accessories.
13. Use only recommended accessories. The use of improper accessories may be
hazardous and cause injuries.
14. Never leave the D-Cut Multi-flooring Cutter unattended. Secure the handle
with the lock chain when not in use.

3
Installation of the Cutter
Insert the handle base into the handle
as shown.
Warning: Do not put your fingers
against the sharp edge of the blade at
any time.
Changing the Blade
Use the provided Allan wrench to
remove the four screws, then hold the
blade by each end and carefully move
the blade out of blade holder.
Note: the flat side of the blade facing
the table.
Warning: Do not put your fingers
against the sharp edge of the blade at
any time.
Cut
Insert material between the cutting
blade and the base, flush with the
gauge as shown and hold the material
then push handle down to complete a
cut.

4
Part List

5
Parts Q’ty Parts Q’ty
1 Hex Head Screw M4 × 25 2 24 Working Table 1
2 Washer Φ4 6 25 Ball Handle 1
3 Rubber Feet A 2 26 Hook B 1
4 Lock Nut M4 4 27 Handle 1
5 Nylon Block 1 28 Stopper 1
6 Cutter Base 1 29 Rotating Shaft 2
7 Spring Pin 2 30 Hex Head Screw M5 × 8 2
8 Spring 2 31 Hex Headless Screw M5 × 8 1
9 Pin 2 32 Parallel Pin 1
10 Left End Plate 1 33 Hex Head Screw M6 × 20 1
11 Hex Head Screw M6 × 16 8 34 Spring Washer 1
12 Left Side Plate 1 35 Aluminum Eccentric Cam 1
13 Rubber Feet B 2 36 Blade Holder 1
14 Hex Button Head Screw M6 × 16 4 37 Hex Head Screw M5 × 16 2
15 Hex Button Head Screw M8 × 16 2 38 Nylon Board 2
16 Hex Button Head Screw M4 × 16 2 39 Right End Plate 1
17 Customized Screw M5 2 40 Right Side Plate 1
18 Lock Nut M5 4 41 Lock Nut M8 2
19 Working Table Base 1 42 Hex Head Screw M6 × 8 4
20 End Cap 2 43 Blade 1
21 Hook A 1 44 Allan Wrench M6 1
22 Chain 1 45 Hex Head Screw M5 × 16 4
23 Hex Head Screw M5 × 10 4 46 Hold Bar 1