D-CUT RC-200 User manual

OPERATION MANUAL
Vinyl Wall-base Cutter RC-200
www.dcutproducts.com

2
SAFETY RULES FOR THE FLOORING CUTTER
1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE
OPERATING THE D-Cut MULTI-FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of D-Cut Multi-flooring
Cutter, obtain advice from a qualified instructor or call 630-916-9100 USA
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or
medication.
4. Always wear safety approved eye protection with side shields(ANSI Z87.1)
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the D-Cut Multi-flooring
Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or solid stand.
8. Use the right tool. Do not force the D-Cut Multi-flooring Cutter or use it for a
job for which it was not designed; use only on approved materials.
9. Keep the blade sharp. A dull blade will not perform properly.
10. Always keep hands away from blade while operating or carrying the cutter.
11. Do not alter or misuse this tool. The D-Cut Multi-flooring Cutter is precision
built; modifications not specified in this manual may result in a dangerous
and unsafe environment.
12. Maintain the D-Cut Multi-flooring Cutter with care. Keep Blade sharp and
clean. Follow instructions for changing accessories.
13. Use only recommended accessories. The use of improper accessories may be
hazardous and cause injuries.
14. Never leave the D-Cut Multi-flooring Cutter unattended. Secure the handle
with the lock chain when not in use.

3
Straight Cut
Place the work-piece flush with either side
of the guide bar on the working table and
align the blade to the mark on the
work-piece where needs to be cut. Then
press the handle down to complete the cut.
Bevel Cut (1)
There are five slots on the handle base as
shown. One of them is for straight cut and
other two are for bevel cuts. Pull the knob
out of the angle slot on the swing head and
release the knob to the desired angle slot
as shown.
Handle Assembly
Insert the handle to the handle base
and use the provided screw/ washer
/spring washer to secure as shown.

4
Changing the Blade
Use provided Allan wrench to remove the
five screws as shown, then hold the blade
by each end and carefully remove the
blade out of the blade holder.
Note: when putting a new blade on, keep
the flat side of the blade facing the main
table.
Warning: Do not put your fingers against
the sharp edge of the blade at any time.
Bevel Cut (2)
Place the work-piece flush with either side
of the guide bar on the working table and
align the blade to the mark on the
work-piece where needs to be cut. Then
press the handle down to complete the
cut.
Bevel Cut (3)
Place the work-piece flush with either
side of the guide bar on the working
table and make a cut to get a half inside
corner and a half outside corner Then
turn the work-piece around and place it
flush with other side of the guide bar,
then make the second cut to get
another half inside corner and another
half outside corner.
Note: Keep the flat part of the work-pie
ce down towards the working table.

5
Changing the Nylon Base
Use provided Allan wrench to take off
total 6 screws to remove the working
table , then take off the four screws as
shown to replace the nylon board
when it is necessary.
When the cutter is not in use, you need
to keep the blade in a close position for
the safety.
1. Turn the cutting head to 45°.
2. Press the handle down to make the
blade in a close position
3. Lift the device on the top of the
blade holder to hold the blade holder
from coming up
Transportation and Storage
carry or store the cutter as shown.

6
Explosive View

7
Part List
Parts Q’ty Parts Q’ty
1 Screw M5 x 8 12 41 Screw M8x 16 2
2 Front Working Table 1 42 Cup head Screw M6x 10 2
3 Frame A 1 43 Blade 1
4 Washerφ8x 1.5 4 44 Cutter Base 1
5 Working Table Connection 2 45 Lock Nut M8 4
6 Screw M6 x 20 2 46 Wing Nut 4
7 Spring Washer φ6 x 1.3 4 47 Rear Wheel 2
8 Sector Gear A 2 48 Washer φ8 x 2 14
9 Output Shaft 1 49 Spring Washer φ8 x 1.6 14
10 Handle Base 1 50 Frame D 1
11 Screw M6 x 12 1 51 Screw M6 x 12 5
12 Handle Stop 2 52 Lining Board 2
13 Handle 1 53 Angle Position Shaft 2
14 Handle Ball 1 54 Steel Slot 2
15 Hex Screw M6 x 12 2 55 Rotation Plate 2
16 Blade Base 1 56 Screw M8 x 12 2
17 Hex Screw M6 x 14 2 57 Spring 2
18 Bolt M6 x 32 2 58 Lock Nut M10 2
19 Nylon Stop 2 59 Cover 2
20 Sleeve 2 60 Washer φ4 x 0 .8 12
21 Washer φ12 x 3 2 61 Screw M4x 8 12
22 Lock Nut M12 2 62 Nylon Cover A 2
23 Angle Handle 2 63 Nylon Cover B 2
24 Screw M5 x 10 6 64 Gear Rib 2
25 Frame A 1 65 Nylon Bar 1
26 Rear Working Table 4 66 Nylon Bar Holder 1
27 Screw M5 x 12 5 67 Screw M5 x 14 4
28 Carry Handle 1 68 Lock Nut M8 8
29 Nut M5 3 69 Screw M8 x 37 8
30 Pin with internal thread 2 70 Frame E 1
31 Screw M5 x 14 2 71 Nut 1
32 Frame C 1 72 Front Wheel Shaft 1
33 Rear Wheel Shaft 1 73 Cross Bar B 2
34 Cross Bar A 2 74 Frame F 1
35 Nut M8 2 75 Screw M8 x 16 4
36 Screw M8 x 20 6 76 Front Wheel 2
37 Sector Gear B 2 77 Screw M5 x 16 1
38 Rotation Base 1 78 Spring Washer φ5 1
39 Tension Spring 2 79 Washer φ5 1
40 Rotation Shaft 2