D-CUT AK-360 User manual

OPERATION MANUAL
Carpet Tile / LVT Flooring Cutter AK-360
www.dcutproducts.com

2
SAFETY RULES FOR THE FLOORING CUTTER
1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE
OPERATING THE D-Cut MULTI-FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of D-Cut Multi-flooring
Cutter, obtain advice from a qualified instructor or call 630-916-9100 USA
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or
medication.
4. Always wear safety approved eye protection with side shields(ANSI Z87.1)
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the D-Cut Multi-flooring
Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or solid floor.
8. Use the right tool. Do not force the D-Cut Multi-flooring Cutter or use it for a
job for which it was not designed; use only on approved materials.
9. Keep the blade in a good shape. A chipped blade will not perform properly.
10. Always keep hands away from blade while operating or carrying the cutter.
11. Do not alter or misuse this tool. The D-Cut Multi-flooring Cutter is precision
built; modifications not specified in this manual may result in a dangerous
and unsafe environment.
12. Maintain the D-Cut Multi-flooring Cutter with care. Keep Blade sharp and
clean. Follow instructions for changing accessories.
13. Use only recommended accessories. The use of improper accessories may be
hazardous and cause injuries.
14. Never leave the D-Cut Multi-flooring Cutter unattended. Secure the handle
under the working table when not in use.

3
CUTTING AND C
Installation of the Cutter (1)
Install the Cam assembly to the cutter
base with provided nuts and rotating
shaft as shown.
After the cam bar is installed properly,
remove the red nylon stopper so the
cutter is ready for the cutting job.
Straight Cut
Insert the floor plank between the
cutting blade and the base, flush with
the guide bar on the working table and
hold the plank, and then press the
handle down to complete a cut.
Warning: Maintain control of the
handle. Do not allow handle to slam
back after making a cut.
Installation of the Cutter (2)
Install the extended working table to
the cutter base with provided screws as
shown.
Install the handle assembly to the cutter
base with provided screws as shown.
Warning: Do not put your fingers
against the sharp edge of the blade at
any time.

4
Lengthwise Cut
Insert the floor plank between the
cutting blade and the working table
along with the guiding bar which
can be locked on both sides of the
working table. Keep moving the
plank along with the guide bar after
each cut until the whole plank is
completely cut.
Notch Cut
Make a lengthwise cut first to the
desired length on the floor plank as
mentioned above, then turn the
plank at 90°, and put desired cutting
point right under the blade.
Unlock two screws on both side of
the blade holder as shown and pull
out the blade holder out to above
mentioned desired cutting point,
then press the handle down to
complete a cut.
45°Cut
Position the guide bar at 45°. Insert the
floor plank between the cutting blade
and the base, along with the guide bar
as shown, and then press the handle
down to complete a cut.

5
Transportation
Slide the lock pins to the lock position
to lock the cutting head when the cutter
is not in use to keep the blade in a close
position for the safety as shown on top
illustration.
Insert the handle to the handle storage
as shown when the cutter is not in use
or in transportation.
Changing the Nylon Bar
Use the provided Allan wrench to
remove the four screws, then hold the
nylon bar and carefully move it out of
nylon bar holder.
Warning: Do not put your fingers
against the sharp edge of the blade at
any time.
Changing the Blade
First loosen the two screws on the
blade and remove the stopper
screw on the blade holder and pull
out the blade as shown. Use
provided Allan wrench to remove
the nine screws, and then carefully
move the blade out of the small
blade holder.
Note: the flat side of the blade
should face the working table when
installing a new blade.
Warning: Do not put your fingers
against the sharp edge of the blade
at any time.

6
Explosive View

7
Parts
Q’ty
Parts
Q’ty
1
Screw M6×45
2
25
Blade Holder Assembly
1
2
Spring washer φ6
11
26
LED Belt Assembly
1
3
Wheel
2
27
Nylon Bar A
2
4
Nut M10
6
28
Right Handle
1
5
Welding Assembly
1
29
Screw M4×31
2
6
Guide Pillar Base
2
30
Handle A
1
7
Short Guide Pillar
2
31
Left Handle
1
8
Long Guide Pillar
2
32
Nut M4
2
9
Screw M6×16
8
33
Knurling Screw M8
2
10
Screw M5×14
6
34
Handle B
1
11
Nylon Bar holder
1
35
Bolt M12×110
2
12
Nylon Bar
2
36
Handle Base
2
13
Nylon Bar Base
1
37
Aluminum Cam Wheel
1
14
Main Working Table Base
2
38
Guide Bar
1
15
Screw M6×20
4
39
Blade holder Base
1
16
Washer φ6
13
40
Screw M6×10
1
17
Rubber Feet
2
41
Rotating Shaft
1
18
Extend Working Table Base Assembly
1
42
Nylon Bar B
2
19
Screw M8×12
4
43
Washer
2
20
Gross Bar
2
44
Nut M8
1
21
Extend Working Table
1
45
Screw M5×1 6
4
22
Screw M5×20
12
46
Nylon Cam
4
23
Main Working Table
1
47
Nut M12
1
24
Blade
1
48
Shaft for Wheel
1
Explosive View