D-Link DAP-2620 User manual

This document will guide you through the basic
installation process for your new access point.
Building Networks for People
DAP-2620
Documentation also available
via the D-Link Website
Quick Installation Guide
Wireless AC1200 Wave 2 Dual-Band
Wall-Plate PoE Access Point

2
Before You Begin
This installation guide provides instructions
for installing the DAP-2620 on your network.
Additional documentation is also available on
the D-Link support website.
• D-Link Nuclias Connect User Manual: For
additional information and instructions
on how to configure the device using
D-Link Nuclias Connect.
• DAP-2620 User Manual: For additional
information and instructions on how to
congure the device using the web user
interface.
Package Contents
This DAP-2620 package should include the
following items:
• 1 x DAP-2620
• 1 x Quick Install Card
• 1 x Mounting bracket
• 1 x Allen key and screw
If any of the above items are damaged or missing,
please contact your local D-Link reseller.
System Requirements
• A PC or laptop with a working Ethernet
adapter or wireless interface.
• Mozilla Firefox 52.0 or higher, Internet
Explorer 11 or higher, Safari 10.1 or higher,
Google Chrome 59 or higher.
• OS X 10.8.5, Windows 7, Linux (Ubuntu 12)
and higher.
Hardware Overview
LED Indicators
Figure 1: Front Panel LED
# LED Status Description
1
Power/
Status
LED
Solid
green
Indicates that
the access point
is working
correctly
Solid
red
Indicates that the
access point has
malfunctioned.
Table 1: LED Description
Interface Connectors
Figure 2: Bottom Connectors
# Connector Description
1 LAN Port Gigabit RJ-45
port for data.
2Telephone
Port
RJ-11 port for
connection
to phones.
3 Reset Button
Used for resetting
the device back
to factory default
settings.
Table 2: Interface Description
Figure 3: Back Connectors
1
3
12
1 2

3
# Connector Description
1Telephone
Port
RJ-11 port for a
telephone cable.
2LAN Port
(PoE)
Gigabit RJ-45 port for
data and Power over
Ethernet (PoE) power.
Table 3: Interface Description
Powering the Access Point
Use a standard Ethernet cable to connect the
LAN port on the DAP-2620 to a PoE power source
device such as a PoE switch or PoE injector.
Conguring the Access Point
Note: D-Link recommends conguring the
device before mounting it.
Using D-Link Nuclias Connect
The DAP-2620 is designed to be managed
through D-Link Nuclias Connect. Refer to the
D-Link Nuclias Connect Manual for detailed
conguration instructions.
Figure 4: Connecting through Nuclias Connect
1. Download the free Nuclias Connect
app from the App Store or Google Play
by searching for Nuclias Connect or by
scanning the QR code below.
2. Open the Nuclias Connect app and follow
the onscreen instructions to discover and
set up your device.
Manual Conguration
If you are not using Nuclias Connect, you may
manually congure the DAP-2620 using its web
user interface (UI). Refer to the DAP-2620 User
Manual for detailed conguration instructions.
Use the following methods to access the web
user interface:
Note: The management computer must be in
the same subnet as the DAP-2620.
1. Use an Ethernet cable to connect the
management computer to the PoE switch
or to the PoE Injector the DAP-2620 is
connected to.
2. Open a web browser on the management
computer and type in dap2620.local in the
address eld and press Enter.
3. When prompted, enter the default login
credentials:
User name: admin
Password: admin
Mounting the Access Point
For optimal coverage, mount the DAP-2620 on
the wall. An Ethernet cable running through
an electrical wall box should be pre-installed
before mounting.
1. Remove the mounting plate from the
device.
2. The Ethernet cable and the telephone
cable (optional) should pass through the
mounting plate. Attach the mounting plate
to the electrical wall box.
Figure 5: Attaching the Mounting Plate
Nuclias Connect
Software
DAP-2620 POE Switch or Router

4
3. Connect the Ethernet cable and telephone
cable (optional) to the device.
Figure 6: Connecting the Cables
4. Attach the DAP-2620 to the mounting
plate by snapping the device into place
onto the plate and use the Allen key and
screw to lock it in at the top.
Figure 7: Locking the Lock Plate
Reboot/Reset the Access Point
If necessary, the DAP-2620 can be manually
rebooted or reset to factory default settings.
Rebooting the device
Unplug the Ethernet cable to power o the
device and replug it to power it on again.
Resetting the device
Press and hold down the recessed reset
button at the bottom of the device between
6 to 15 seconds then release to reset the device
to its factory default settings.
Additional Information
For additional support, please refer to the
user manual, or visit your local D-Link support
website.

5
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Non-modications Statement:
Any changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For
product available in the USA/Canada market, only channel 1~11 can be operated. Selection of
other channels is not possible.
Note
The country code selection is for non-USA models only and is not available to all USA models. Per
FCC regulations, all WiFi product marketed in the USA must be xed to USA operational channels
only.
RF Frequency Requirements
This device is for indoor use only when using all channels in the 5.15 to 5.25 GHz frequency range.
High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz
bands. These radar stations can cause interference with and/or damage this device. This device
will not operate on channels which overlap the 5600-5650 MHz band.
It is restricted to indoor environments only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 24 cm
between the radiator and your body.

6
Product and Warranty Information
To nd out more about D-Link products or marketing information, please visit the website http://
www.dlink.com.
The D-Link Limited Lifetime Warranty information is available at
http://warranty.dlink.com/
位置: 中文使用說明書
電池使用安全說明
低功率警語:
• 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更
頻率、 加大功率或變更原設計之特性及功能。
• 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應
立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之
無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機
設備之干擾。
• 使用此產品時應避免影響附近雷達系統之操作。

7

Ver. 2.00(WW)_130x183
2019/10/07
5300-00007534-01W