D-Link DIS-2650AP User manual

Quick Installation Guide
Wireless AC1200 Wave 2 Industrial Indoor Access Point
DIS-2650AP
DIS-2650AP
5G 2.4G ALARM POE PWR2 PWR1 STATUS SIGNAL
CONSOLE RESET LAN 2 LAN1/ POE
Additional documentation is also available on the D-Link website

Contents
English 1

Before You Begin Hardware Overview
This Quick Installation Guide gives you step-by-
step instructions for setting up your DIS-
2650AP Wireless Access Point. The model you
have purchased may appear slightly different
from the one shown in the illustrations. For
more detailed information about the router,
please refer to the User Manual.
Package Contents
This DIS-2650AP package includes the
following items:
• DIS-2650AP
• Quick Installation Guide
• DIN rail mounting kit
• 4 installation screws (3 x 7 mm)
• Bracket
If any of the above items are damaged or missing,
please contact your local D-Link reseller.
System Requirements
• Computers with Windows®, Macintosh®,
or Linux-based operating systems with an
installed Ethernet Adapter
Front Panel Features
1 2 3 4 5 6 7
8
9
10
DIS-2650AP
5G 2.4G ALARM POE PWR2 PWR1STATUS SIGNAL
CONSOLE RESET
LAN2
LAN1/ POE
Figure 1: Front Panel
#
Feature Description
1
Console
Console port which is used to
connect to the device using an
Port
RJ-45 to serial cable.
2 Reset Press and hold to perform a
Button factory reset.
3
LAN2
10/100/1000 Mbps Ethernet
LAN port.
4 LAN1/PoE PoE-capable Ethernet LAN port.
5 5G/2.4G A green LED indicates the
LEDDIS-2650AP is receiving power.
6
Alarm
A light indicates that the power
supply has failed.
7
PoE
Indicates whether a device is
receiving power on the PoE port.
8
PWR1/2
Indicates whether power sources
1 and 2 are connected.
9
Status
Indicates the device’s operational
status.
10
Signal
Indicates the strength of the
signal the device is receiving.
Table 1: Right Panel Feature Descriptions
ENGLISH
DIS-2650AP Quick Installation Guide 1

ENGLISH
Side Panel Features
1 2
Figure 2: Left Panel Interface Connectors
#
Connector
Description
1 Switch Ground This is used to connect
the device to ground.
This is used to connect the
2 Terminal Block device to external power sources
and an alarm relay.
Table 2: Side Panel Features
Hardware Installation
Before You Begin
Observe the following precautions to help
prevent shutdowns, equipment failures,
and personal injury:
• Install the DIS-2650AP in a cool and
dry place.
• Install the DIS-2650AP in a site free
from strong electromagnetic sources,
vibration, dust, excessive moisture,
and direct sunlight.
• Place antennas in an unobstructed area
with a clear signal. Avoid metal boxes,
brick walls, and other dense materials.
• Visually inspect the power connector
and make sure that it is fully secure.
• Do not stack any devices on top of
the DIS-2650AP.
Attach the External Antennas
The DIS-2650AP requires two external antennas to
function correctly. The included antennas are
interchangeable
1. Attach the two included antennas to
the RP-SMA connectors on the side
of the DIS-2650AP. Turn clockwise
to fasten the antennas.
2. Arrange the antennas so that they’re
pointing upwards and in a configuration
to receive optimal signals.
Mounting the Device on a Wall
The DIS-2650AP can be installed on a
solid surface by using the included wall
mounting plates attached to the back of
the device. Use the following instructions
to install the DIS-2650AP on a wall:
1. Align the cross-section of the mounting
plates with the openings on the back of
the device. Secure the plates with the
included mounting screws.
Figure 3: Attaching Mounting Plates
2. Remove the DIN rail mounting clip from
the back of the device (if present).
2 DIS-2650AP Quick Installation Guide

3. Place the mounting brackets
(attached to the device) on the
location where you want to mount it,
and use the brackets as a guide to
mark where to drill the screw holes.
4. Drill holes on the marks and insert
wall anchors appropriate for the
material of the wall.
5. Align the device with the wall anchors and
secure it to the wall using appropriate
screws for the wall anchors.
Installing the Device on a DIN Rail
The DIS-2650AP can be mounted on a standard
DIN rail using the included DIN mounting kit.
Use the following instructions to install the
DIS-2650AP on a rail:
1. Check that the DIN rail is installed properly
using at least two screws on each end.
2. Fasten the DIN mounting clip to the
rear panel of the device using the
included mounting screws.
Installing the Device into a Rack
The DIS-2650AP can be mounted on a
standard rack using the included mounting
plates. To install the device on a rack:
1.
Attach the mounting brackets to the rear
panel of the device using the
provided installation screws.
Figure 5: Installing onto a Rack
2. Use the provided screws to attach the
two rear mounting plates to the rack.
Figure 4: Hooking onto the Rail
3. Position the DIS-2650AP against the
rail, then tilt it upwards and hook the
DIN rail clip on the back of the device
against the rail. Snap the device into
place to complete the installation.
Grounding the Device
To use the DIS-2650AP safely, it needs to
be grounded. Please complete these
steps before powering on the device.
1. Remove the grounding screw from
the top of the DIS-2650AP and place
the grounding cable lug ring on top
of the grounding screw opening.
2. Insert the grounding screw back into
the grounding screw opening and
use a screwdriver to tighten the
grounding screw, securing the
grounding cable to the DIS-2650AP.
3. Attach the terminal lug ring at the
other end of the grounding cable to
an appropriate grounding source.
DIS-2650AP Quick Installation Guide 3

Powering the Device
The DIS-2650AP can be powered with an 802.3at
PoE source or by using the built-in terminal
EN
GL IS H
adapter. This allows dual power inputs using
wires from the power source(s) to be screwed
into the terminal connections.
Using the Terminal Connections
1.
Before continuing, consult the diagram
below to decide which wires from the
power source need to connect to which
contacts on the terminal block. Note
that two power sources can be used;
one inserted into V1-/V1+ (labeled
PWR 1) and the other inserted into
V2-/V2+ (labeled PWR2).
Figure 6: Terminal Block Diagram
2. Use a lever to remove the terminal
block from the switch.
Figure 7: Removing the Terminal Block
3. Use a flat head screwdriver to unscrew the
terminal connections that you wish to use.
4. Insert the wires into the terminal
connectiosn and use the screwdriver to
tighten the screws to secure the wires.
Figure 8: Connecting a Power
Source to the Terminal Block
5. Re-insert the terminal block into the
socket on the device.
Connecting Devices
The Ethernet port can be connected to an
end device. Use a standard Category
5/5e/6 RJ-45 Ethernet cable to connect
the end device to the DIS-2650AP.
The port will auto-negotiate to the highest
possible port speed based on the
connected device.
Management Options
The DIS-2650AP can be managed by
using the Web User Interface (Web UI),
the Nuclias Connect app, or the console
port or Telnet management interfaces.
4 DIS-2650AP Quick Installation Guide

Nuclias Connect App Configuration
1. Download the free Nuclias Connect
app from the App Store or Google Play
by searching for Nuclias Connect or
by scanning the QR code below.
2. Open the Nuclias Connect app and
follow the onscreen instructions to
discover and set up your device.
Manual Configuration
Note: The management computer, DHCP server
and DIS-2650AP must be in the same subnet.
Use one of the following methods to
access the web user interface:
Connecting through Ethernet
1. Use an Ethernet cable to connect the
DIS-2650AP to the management
computer, or to the switch or router the
management computer is connected to.
2. Manage the access point from a
computer. Enter dis2650ap.local in
the address field of your browser.
3. Log in to the administration user
interface. The default information is:
Username: admin
Password: admin
Connecting Wirelessly
1. Connect the management computer to the
default SSID of the DIS-2650AP, “dlink.”
2. Manage the access point from a
computer. Enter dis2650ap.local in
the address field of your browser.
3. Log in to the administration user
interface. The default information is:
Username: admin
Password: admin
Additional Information
If you are encountering problems setting up
your network, please refer to the user manual.
Additional help is available online. To find
out more about D-Link products or marketing
information, please visit the D-Link support
website at http://dlink.com/support/.
Warranty Information
The D-Link Limited Lifetime Warranty
information is available at the following
website: http://warranty.dlink.com/.
ENGLISH
DIS-2650AP Quick Installation Guide 5

Appendix - Statements
ErP Power Usage
This device is an Energy Related Product (ErP) that automatically switches to a power-saving
Network Standby mode within 1 minute of no packets being transmitted. It can also be turned off
through a power switch to save energy when it is not needed.
Network Standby: 3.12 watts
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Non-modifications Statement:
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For
product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible.
Note
The country code selection is for non-USA models only and is not available to all USA models. Per FCC
regulations, all WiFi product marketed in the USA must be fixed to USA operational channels only.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

RF Frequency Requirements
This device is for indoor use only when using all channels in the 5.15 to 5.25 GHz frequency range.
High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz
bands. These radar stations can cause interference with and/or damage this device. This device
will not operate on channels which overlap the 5600-5650 MHz band.
It is restricted to indoor environments only.
IMPORTANT NOTICE:
Innovation, Science and Economic Development Canada (ISED) Statement:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Innovation, Science and Economic Development Canada (ISED) Statement:
This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential
for harmful interference to co-channel mobile satellite systems;
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
Operations in the 5.25-5.35 GHz band are restricted to indoor usage only.
Les opérations dans la bande de 5.25-5.35 GHz sont limités à un usage intérieur seulement.
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.
Déclaration d’exposition aux radiations
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm
de distance entre la source de rayonnement et votre corps.

Japan Voluntary Control Council for Interference Statement
この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、こ
の装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい。
Japan Voluntary Control Council for Interference Statement
This is a Class B product based on the standard of the VCCI Council. If this is used near a
radio or television receiver in a domestic environment, it may cause radio interference.
Install and use the equipment according to the instruction manual.
電波法により 5GHz 帯は屋内使用に限ります。
Product and Warranty Information
To find out more about D-Link Nuclias product or marketing information, please visit the
website http://www.dlink.com or https://www.nuclias.com.
The D-Link Limited Lifetime Warranty information is
available at http://www.dlink.com/warranty
VCCI-B
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停
用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
==========================================================================
For UNII 產品(5GHz WLAN/WIFI)
==========================================================================
1. 使用此產品時應避免影響附近雷達系統之操作。