Dahua ASI1212AD User manual

1
Fingerprint Access Control Integration Host
User’s Manual
V1.1.3

Table of Contents
1Overview......................................................................................................0
2Device Structure and Installation ................................................................. 1
3System Structure.........................................................................................3
3.1 System Structure.............................................................................................3
3.2 Device Port ..................................................................................................... 3
4Function Setting...........................................................................................6
4.1 Login...............................................................................................................6
4.2 User Management...........................................................................................6
4.2.1 Add User...............................................................................................7
4.2.2 Add Super Password ............................................................................8
4.2.3Delete User........................................................................................... 8
4.2.4 Delete Password User ..........................................................................9
4.2.5 Add More Master Card........................................................................ 10
4.3A&C .............................................................................................................. 10
4.3.1 Period ................................................................................................. 10
4.3.2 Master Card........................................................................................ 13
4.3.3 Unlock Mode....................................................................................... 13
4.3.4 Door Lock Time................................................................................... 13
4.3.5 Alarm .................................................................................................. 14
4.3.6 Door Status Setup............................................................................... 15
4.4 System Settings............................................................................................ 15
4.4.1 Local Setup......................................................................................... 15
4.4.2 Communication Setup......................................................................... 17
4.4.3 Mode................................................................................................... 17
4.4.4 Reboot System ................................................................................... 18
4.5 System Info................................................................................................... 18
4.5.1 Card History........................................................................................ 18
4.5.2 Alarm History ...................................................................................... 19

4.5.3 Local Info............................................................................................ 19

Important Safeguards and Warnings
Please read the following safeguards and warnings carefully before using the product in
orderto avoid damages lossesand bodyinjuries.After reading, pleasewell keep this user's
manual.
Note:
Please change user default password after being armed.
Do not install the device at position exposed to sunlight or in high temperature.
Temperature rise in device may cause fire.
Do not expose the device to lampblack, steam or dust. Otherwise it may cause
fire or electric shock.
The devicemust be installed on solid and flat surface in order to guaranteesafety
under load and earthquake. Otherwise, it may cause device to fall off or turnover.
Do not drop or splash liquids onto the device, and do not place container with full
liquid on the device to prevent liquid spilling from entering the device.
Do not block air vent of the device or ventilation around the device. Otherwise,
temperature in device will rise and may cause fire.
Use the device only within rated input and output range.
Do not disassemble the device without professional instruction.
Please transport, use and store the product under appropriate temperature and
humidity.
Warning:
Please use battery properly to avoid fire, explosion and other dangers.
Please replace used battery with battery of the same type.
Do not use power line other than the one specified. Please use it properly within
rated range. Otherwise, it may cause fire or electric shock.
Please use power supply matching SELV requirements, and IEC60950-1 Limited
Power Source. Power supply shall follow requirements on device label.
For I-type structure product, connect it to power supply plug with GND protection.
If you use power plug or appliance coupler as disconnecting device, please
maintain the disconnecting device available to be operated all the time.
Privacy Protection Notice
As the device user or data controller, you might collect personal data of others'
such as face, fingerprints, car plate number, Email address, phone number,
GPS and so on. You need to be in compliance with the local privacy protection
laws and regulations to protect the legitimate rights and interests of other people
by implementing measures include but not limited to: providing clear and visible

identification to inform data subject the existence of surveillance area and
providing related contact.
About the Manual
The Manual is for reference only. If there is inconsistency between the
Manual and the actual product, the actual product shall prevail.
We are not liable for any loss caused by the operations that do not comply
with the Manual.
The Manual would be updated according to the latest laws and regulations
of related regions. For detailed information, see the paper User's Manual,
CD-ROM, QR code or our official website. If there is inconsistency between
paper User's Manual and the electronic version, the electronic version shall
prevail.
All the designs and software are subject to change without prior written notice.
The product updates might cause some differences between the actual
product and the Manual. Please contact the customer service for the latest
program and supplementary documentation.
There still might be deviation in technical data, functions and operations
description, or errors in print. If there is any doubt or dispute, please refer to
our final explanation.
Upgrade the reader software or try other mainstream reader software if the
Guide (in PDF format) cannot be opened.
Alltrademarks,registeredtrademarksandthecompanynamesin the Manual
are the properties of their respective owners.
Please visit our website, contact the supplier or customer service if there is
any problem occurred when using the device.
If there is any uncertainty or controversy, please refer to our final explanation.

0
1 Overview
The Fingerprint Access Control Integration Host integrates card reading, config and
execution functions. Its has a neat appearance for medium to high-end clients such as
commercial building, corporation and intelligent community.
It has:
Touch keyboard + LCD display, TCP/IP protocol.
Support unlock via card, fingerprint, password, card+password, card+fingerprint, card
or password or fingerprint.
Max support 3,000 fingerprints, 30,000 valid cards and 500 super-passwords.
Max support 150,000 card records and 512 alarm records.
Door time out alarm, intrusion alarm, duress alarm, and door sensor alarm.
Ring input.
Add guest card, duress card, black/white list and patrol card, while support period of
validity or times.
Integrate card reader and single-door controller.
Support 128 groups of period and 128 groups of holiday period.
Warning:
If this product required external power, please use 12V 0.5A adaptor and the work
temperature shall be within -5℃～55℃.

1
2 Device Structure and Installation
Device appearance and dimension are shown as in Figure 2- 1 and Figure 2- 2.
Unit is mm.
Figure 2- 1
Figure 2- 2

2
FingerprintAccess Control Integration Host installation is shown as in Figure 2- 3.
Figure 2- 3
Installation step:
Step 1. Fix installation bracket in the hole on 86 box via screw A as to fix the bracket on
wall (if no 86 box or you cannot fix it well, then use screw B to fix the bracket on wall,
but you must embed expansion nut at the corresponding position in wall before doing
so).
Step 2. According to installation map, hang the device on bracket hook.

3
3 System Structure
3.1 System Structure
The device and card reader, alarm device, access control PC and etc. compose a system
as in Figure 3- 1.
Figure 3- 1
3.2 Device Port
Device port of the host is shown in Figure 3- 3.

4
Figure 3- 2
Figure 3- 3
No. Port Note
1
COM
Door lock COM end
NC
Door lock NC end
NO
Door lock NO end
SR
Door sensor detection
GND Connect to GND
PUSH Press unlock button
2 BELL- Door bell output
BELL+
OUT2- Alarmoutput2（5V level switch），connect

5
No. Port Note
OUT2+ to voltage not over 12V
OUT1- Alarmoutput1（5Vlevelswitch）,connect
to voltage not over 12V
OUT1+
3
485+
RS485+, 485 card reader
485-
RS485-, 485 card reader
LED
LED_OUT, Weigand card reader
D0
D0, Weigand card reader
D1
D1, Weigand card reader
CASE Card reader protection alarm
4 GND Connect to GND
12V 12V power output, power supply of card
reader
485+
RS485+
485- RS485-
GND Connect to GND
ALARM Alarm input

6
4 Function Setting
4.1 Login
Login interface step:
Step 1. Plug in power, device is going to boot up.
Step 2. Press 【√】button, screen displays admin password.
Step 3. Input admin password, and press 【√】button to enter homepage.
Default password is “88888888”.
You can select to enter user management, A&C setting, system setting and local
info as main menu.
Press 【↑】button to move up.
Press 【↓】button to move down.
Press 【√】button to enter or confirm.
Press 【 】 button to return or exit.
Press 【←】button to backspace.
Press 【 】 button to ring.
4.2 User Management
You can add or delete card, password.
You also can add user as you add card orfingerprint, and you can bind card and fingerprint.
Card type includes general, VIP, guest, patrol, black list and duress.
Please refer to Chart 4- 1.
Card Type
Note
General card General user card.
When you add card, system will ask if set card password,
period and term of validity.
VIP card
VIP user card. It warns service personal when cardholder
enters.
When you add card, system will ask if set card password,
period and term of validity.
Guest card When you add guest card, you need to set usage times. So
when it exceeds this limit, the card becomes invalid.
Patrol card
Patrol card can only swipe card at patrol spot but cannot
unlock.
When you add card, system will ask if set card password,
period and term of validity.

7
Card Type
Note
Black list
When you swipe card on black list and enters, it wanrns
service personal.
When you add card, system will ask if set card password,
period and term of validity.
Duress card Duress card becomes valid after you set duress alarm. You
can swipe this card to unlock, but an alarm will be send to
center.
Chart 4- 1
Note:
All of these cards will be sent to center, management platform will process according to
card type.
Password user represents user who input password in setup to enter.
Note:
Card user has not set password, and you shall set unlock mode to card, card or
password or fingerprint in order to enter.
Card user set card password,and you shall set unlock mode to card, card + password,
card or password or fingerprint in order to enter.
Card user set fingerprint, but before entering, user shall set unlock mode to card, card
+ password, card or password or fingerprint.
User, who set period, can only unlock door within designated period.
Password user, shall set unlock mode to password, card or password or fingerprint in
order to enter.
4.2.1 Add User
To add user:
Step 1. In homepage, press 【↑】or【↓】key to select user management, press 【√】
key.
Step 2. Press 【↑】or【↓】keytomoveup ordown, selectadduserand press【√】key.
New User
Card No.
Card Type Normal
Use Time 255 （Guest）

8
Step 3. Use key to input card no. or place card at swiping area to scan.
Step 4. Press【√】key to select card type.
Step 5. Press 【←】key to delete default data, input use time, and press 【√】.System
shows added password and period interface as follows.
Note:
Use time if for guest card only.
Step 6. Press 【←】key to delete default data, input user password, period and validity,
and press 【√】key. System asks if you want to record fingerprint.
Step 7. According to actual condition, select “yes” or “no”.
If you select YES, system will instruct you to place finger.
If you select NO, system will inform the info input is successful.
4.2.2 Add Super Password
To add super password:
Step 1. In usermanagement,press 【↑】keyor 【↓】keytomoveupanddown,andselect
add super password. Press 【√】key.
System shows add new super password interface.
Step 2. Input super password no. and press 【√】.
Step 3. Input super password and confirm. Press 【√】key as follows.
4.2.3 Delete User
You can delete a single user, or all users.
To delete a single user:
Step 1. Inusermanagementinterface,press 【↑】or 【↓】keytoselectdeleteuser,and
New User
Card No. 1
Password 123456
Period 255
Validity 2099-12-30
Add Super Pwd
Pwd input ******
Confirm ******

9
press 【√】key.
Step 2. Press【↑】or【↓】key, to move up or down, select single card and press【√】
key.
Step 3. Input no. of card to delete, place the card at swiping area, and press【√】key.
System asks if to delete it or not.
Step 4. Select OK and press 【√】key to delete single card.
To delete all users:
Step 1. In delete user interface,move up or down to select all users, and press 【√】key.
System asks if to delete all or not.
Step 2. Press 【√】key to confirm. System says deleted successfully.
4.2.4 Delete Password User
You can delete a single super password or delete all super passwords.
To delete a single password user:
Step 1. Indeleteuserinterface,press 【↑】or 【↓】keyto selectdeletesuperpassword,
and press 【√】key.
Step 2. Press 【↑】or【↓】keyto moveup ordown,selectdeletesinglesuperpassword
and press【√】key.
Step 3. Input no. of super password to delete, and press【√】key.
System asks if to delete it or not.
Step 4. Press OK and press【√】key to delete.
To delete all super passwords:
Step 1. In delete super password interface, press 【↑】or 【↓】key to select delete all
super passwords, and press 【√】key. System asks if to delete all or not.
Step 2. Press 【#】key to delete.
Step 3. Select OK and press 【√】key. System says deleted successfully
Delete User
User Card No.
Delete Super Pwd
Super Password

10
4.2.5 Add More Master Card
By adding more master card, user can quickly add card user. Before adding master card,
user shall add master card first, please refer to Ch 4.3.2.
To add more master card:
Step 1. In user management interface, by pressing 【↑】or 【↓】key to move up and
down,selectadd moremastercard,and press 【√】key.Systempromptusertoswipe
the card.
Step 2. Place master card on swiping area and scan. System promptsmaster card mode.
Step 3. Place card to add one by one at the swiping area to scan. System says added
successfully.
4.3 A&C
4.3.1 Period
You can set unlock period, including card swiping period, holiday period, mode period and
NO period.
4.3.1.1 Card Swiping Period
Card swiping period can be 0~127, a total of 128 periods. In each period, you need to set
schedule for each day of week. When a new card is added, and set card swiping period,
then user swipe card to unlock.Access control will judge if current time is withinset period.
For example, set period 1, and the Monday to Sunday setup are in Chart 4- 2.
Day
Period
Monday
0800-2200 (valid period: 08:00 to 22:00)
Tuesday
0800-2200 (valid period: 08:00 to 22:00)
Wednesday
0800-2200 (valid period: 08:00 to 22:00)
Thursday
0800-2200 (valid period: 08:00 to 22:00)
Friday 0800-2200 (valid period: 08:00 to 22:00)
Saturday 0800-2200 (valid period: 08:00 to 22:00)
Sunday 0800-2200 (valid period: 08:00 to 22:00)
Chart 4- 2
To set card swiping period:
Step 1. Inhomepage,press 【↑】or【↓】keytomoveupor down,selectA&C setup,and
press【√】key.
Step 2. Press【↑】or 【↓】keyto selecttime period,andpress【√】key. Enter timesetup

11
interface.
Step 3. Press 【↑】key or 【↓】key , select card swiping period, and press 【√】key.
Step 4. Input time period, and press 【√】key. Inputany number between 0~127. Screen
displays period.
Step 5. Modify period and press 【√】key.
Step 6. Set other periods. System asks if save it or not.
Step 7. Press【 】key, system asks if to save config or not.
Step 8. Select YES, and press 【√】key. System says saved successfully.
When new card set period 1, and user use it to unlock door. According to time period
set, system judge if it is within unlock period. Other periods cannot unlock door.
Note:
Default period is full periods.
4.3.1.2 Holiday period
Holiday period can be 0~127, a total of 128 periods. When time is any period in 0~127, all
cards or passwords cannot unlock door.
To set holiday period:
Step 1. In time period setup page, press【↑】or【↓】key to select holiday period, and
press【√】key.
Step 2. Input period, and press 【√】key. Input any number between 0~127, such as 1.
Step 3. Modify start time, end time and swiping period, and press 【√】key.
System prompts
Card Period Setup
Mon.
Tue. 00: 00 – 23: 59
Wed. 00: 00 – 23: 59
Thu. 00: 00 – 23: 59
Fri. 00: 00 – 23: 59
Sat.
Sun.
Holiday Period Setup
Holiday Start：2015-03-25
Holiday End：2015-03-25
Card Period：255

12
4.3.1.3 Mode Period
Mode period has four periods per day, from Monday to Sunday, 7 days a week.
To set mode period:
Step 1. In time period setup interface, press 【↑】or【↓】key, select mode period, and
press【√】. System displays periods of Monday to Sunday.
Step 2. For example select Monday, and press 【√】key.
Step 3. Config period, press 【√】to select unlock mode of the period
Step 4. Config Tuesday to Sunday periods.
Step 5. Press 【 】key. System asks if save or not.
Step 6. Select YES, and press 【√】key. System says saved successful.
After completion,A&C unlock method will be managed accordingto the four periods.
4.3.1.4 NO Period
After user set NO period,A&C will be open during this period.
To set NO period:
Step 1. Intimesetupinterface,press 【↑】or 【↓】key to moveup and down,select NO
period, and press 【√】key.
Step 2. Input period no., and press 【√】key as follows.
System prompts setup is successful. Period no. is the no. set in card swiping period setup.
Mode Period Setup
Mon.
Tue. 00: 00 – 23: 59 Ca/Fw/Fp
Wed. 00: 00 – 23: 59 Ca/Fw/Fp
Thu. 00: 00 – 23: 59 Ca/Fw/Fp
Fri. 00: 00 – 23: 59 Ca/Fw/Fp
Sat.
Sun.
NO Period Setup
Period No. 255

13
4.3.2 Master Card
You can modify or add master card.
Step 1. In A&C setup interface, press 【↑】key or 【↓】key to select master card setup,
and press 【↓】key.
Step 2. Press 【←】key to delete old card no., and input modified card no., or directly
place the card at swiping area for scanning, and press 【√】key, as follows.
System prompts setup is successful.
4.3.3 Unlock Mode
Unlock mode includes card, password, fingerprint, card+password, card+fingerprint, card
or password or fingerprint.
To set:
Step 1. InA&Cinterface,press【↑】or 【↓】keytomoveupor down, selectunlockmode,
and press【√】. Enter unlock mode setup page.
Step 2. Press【↑】or 【↓】key to select mode to set, and press 【√】key. When it is
selected, there will be a ○
√next to the mode.
4.3.4 Door Lock Time
Door lock time setup includes hold time and over time setup.
Step 1. In A&C setup, press【↑】keyor 【↓】key, select door lock time setup and press
【√】key.
Master Card Setup
Card No. FFFFFFFF
Unlock Mode Setup
Card
Password
Fingerprint
Card/Fwd/FP
Card+Pwd ○
√
Card+FP

14
Step 2. Press【←】keytodeleteoriginaldata,inputholdtimeandovertime,press 【√】
key.
System prompt setup is successful.
Door lock hold time is the time doorremains open after userswipe card. If the door remains
open exceeding “over time”, it will send alarm.
4.3.5 Alarm
User can enable or disable alarm, system alarm includes intrusion, anti-pass back, duress
card, door sensor and door timed out. Please refer to Chart 4- 3.
Alarm Type
Note
Intrusion Enter without valid card swiping or password, it will
generate an alarm.
Anti-pass back
Must swipe card when enter/exit, otherwise it will
generate an alarm.
Duress Card Enter with duress card, it will generate an alarm.
Door Sensor
When A&C device is damaged, it will generate an
alarm.
Door Timed Out When A&C open time is over Door Over time, it will
generate an alarm.
Door timed out alarm requires setup of door over
time, please refer to Ch 4.3.4.
Chart 4- 3
To set alarm:
Step 1. InA&Cinterface,press 【↑】keyor 【↓】key,selectalarmsetup,andpress 【√】
key. Enter alarm setup interface.
Step 2. Press【↑】keyor【↓】key,selectalarmtoturnON, and press【√】keyas follows.
Door Lock Time Setup
Hold Time：2000 MS
Over Time：60 S